Oreck U3771 Support and Manuals
Popular Oreck U3771 Manual Pages
Owners Guide - Page 1
76055-01 REV A
Powerful, Lightweight Upright Vacuum
XL® Silver Series - Read all instructions carefully, and keep for future reference. U3771
User's Guide
Important!
Owners Guide - Page 2
...in this manual. ENGLISH
Safety. When using ...service at one blade is present. • Do not pick up flammable or combustible liquids, such as chlorine bleach, drain cleaner, gasoline, etc. Keep the unit moving parts...not allow to install the proper outlet....INSTRUCTIONS
Household Use Only
A polarized plug has one rounded prong and one stationary position for purchasing our Oreck XL® U3771...
Owners Guide - Page 3
... Odor Fighting Dust Bag 6 Replacing Worn Belt 6 Adjusting or Replacing Brushroll 6 Replacing Edge Brush 7 Using an Oreck Fresh Air® Tabs 7 Replacing Light Bulbs 7 Stuffing or Blockage 8
Troubleshooting 8 Parts 9
Accessories & Replacement Parts 9 Warranty 9 Español Guía Del Usuario 10 Guide D'utilisation Français 19
Operation.
Parts List
1 Handle 2 On/Off...
Owners Guide - Page 4
...'s SO lightweight and easy to the user. OFF ( O ) switch on connector...unusual noise, STOP OPERATION and service. 4. Insert short screw ...when ready to "U" shaped part on wet or damp ... use on plug.
4
5
Operating Instructions
This new ORECK Upright is recommended that these be
removed...2
3
Operating the U3771
Make sure the Disposable Odor Fighting dust bag is full, REPLACE IT. 3. Do not...
Owners Guide - Page 5
... belt becomes stretched or cut, it is installed properly.
When buying replacement belts, use ONLY ORECK genuine belts.
Do not operate the unit while in operation. Also clean the connector deflector assembly area, base of cleaning. To obtain the most satisfying years of service read the instructions and keep them handy for any period of...
Owners Guide - Page 6
... out of power head. 13 Fold door away from electrical outlet before servicing. BAG INSTALLATION: 9 Slide the cardboard collar completely onto bag dock door. 10 Firmly push bag dock door with both bearing assembly settings are the same and face up when replacing the brushroll. 15 Reassemble the belt. 16 Reassemble the baseplate.
6 ENFONCEZ...
Owners Guide - Page 7
... from holder and replace with new ones. Unmatched settings can cause damage to the intake tube.
Turn the power head over. Then, remove the brushroll from the housing. 21 Remove the fascia by removing 5 screws. 20 Remove the belt from electrical outlet before servicing.
Using an Oreck Fresh Air® Tab
Your ORECK U3771 vacuum cleaner...
Owners Guide - Page 8
...Service Center for repair. • Check bearing seal. Stuffing or Blockage
IMPORTANT: On plush and new carpets, stuffing may occur inside fan housing. If your own troubleshooter by removing 5 screws (see "Adjusting or Replacing...guide.
When that appear to be major can often be done by first lining up . Replace tube by an
Oreck authorized service center.
24
25
26
27
28
29
Problem
...
Owners Guide - Page 9
...may also have your model number from any direct, indirect, consequential or...replacement of voltages other than Oreck or a participating Factory Authorized Service Center. This warranty gives you specific legal rights, and you the following limited warranty for this product only if it was originally purchased for any part subjected to state. Total Cleaning System
ORECK MANUFACTURING COMPANY: (Oreck...
Oreck U3771 Reviews
Do you have an experience with the Oreck U3771 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Oreck yet.
Earn 750 points for your review!