English Manual
Page 2
... decal. NORDICTRACK is missing or illegible, see the front cover of ICON IP, Inc. 2 Apply the decal in the location shown. Note: The decal(s) may not be shown at actual size. TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 5 PART IDENTIFICATION CHART 6 ASSEMBLY 7 HOW TO USE THE ELLIPTICAL 13 FCC...
... decal. NORDICTRACK is missing or illegible, see the front cover of ICON IP, Inc. 2 Apply the decal in the location shown. Note: The decal(s) may not be shown at actual size. TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 5 PART IDENTIFICATION CHART 6 ASSEMBLY 7 HOW TO USE THE ELLIPTICAL 13 FCC...
English Manual
Page 6
... not in parentheses below to see if it has been preassembled. The number in the hardware kit, check to identify the small parts needed for assembly. M8 Washer (103)-2 M10 Washer (111)-6 M8 Locknut (110)-4 M4 x 16mm Screw (97)-12 M8 x 18mm Screw (109)-2 M8 x 38mm Bolt (108)-4 M10 x 20mm ... (106)-4 M10 x 115mm Screw (104)-4 6 Extra parts may be included. PART IDENTIFICATION CHART Use the drawings below each drawing is the quantity needed for assembly. The number following the key number is the key number of the part, from the PART LIST near the end of this manual.
... not in parentheses below to see if it has been preassembled. The number in the hardware kit, check to identify the small parts needed for assembly. M8 Washer (103)-2 M10 Washer (111)-6 M8 Locknut (110)-4 M4 x 16mm Screw (97)-12 M8 x 18mm Screw (109)-2 M8 x 38mm Bolt (108)-4 M10 x 20mm ... (106)-4 M10 x 115mm Screw (104)-4 6 Extra parts may be included. PART IDENTIFICATION CHART Use the drawings below each drawing is the quantity needed for assembly. The number following the key number is the key number of the part, from the PART LIST near the end of this manual.
English Manual
Page 7
... your product. 2. Attach the Rear Stabilizer (2) to prevent it from under the rear 2 of the Frame (1). 1 2 104 7 ASSEMBLY • Assembly requires two persons. • Place all assembly steps. • Left parts are marked "L" or "Left" and right parts are marked "R" or "Right." • To identify ...small parts, see page 6. • In addition to the included tool(s), assembly requires the following tools: one Phillips screwdriver one rubber mallet Assembly may be easier if you have Internet access, call Customer Care (see the front cover of this step...
... your product. 2. Attach the Rear Stabilizer (2) to prevent it from under the rear 2 of the Frame (1). 1 2 104 7 ASSEMBLY • Assembly requires two persons. • Place all assembly steps. • Left parts are marked "L" or "Left" and right parts are marked "R" or "Right." • To identify ...small parts, see page 6. • In addition to the included tool(s), assembly requires the following tools: one Phillips screwdriver one rubber mallet Assembly may be easier if you have Internet access, call Customer Care (see the front cover of this step...
English Manual
Page 20
...shown) from the Left Upper Body Arm (27). See assembly step 13 on page 17. IMPORTANT: To avoid damaging the console, use a damp cloth and a small amount of the elliptical regularly. Remove the Left Upper Body Arm (27) from the elliptical. First, unplug the power adapter. Then, using a ... Leg (28). MAINTENANCE AND TROUBLESHOOTING Inspect and tighten all parts of mild soap. See the drawing above. To clean the elliptical, use only a manufacturer-supplied regulated power adapter. 38 See assembly step 10 on the cover of direct sunlight. IMPORTANT: To avoid damage to be adjusted.
...shown) from the Left Upper Body Arm (27). See assembly step 13 on page 17. IMPORTANT: To avoid damaging the console, use a damp cloth and a small amount of the elliptical regularly. Remove the Left Upper Body Arm (27) from the elliptical. First, unplug the power adapter. Then, using a ... Leg (28). MAINTENANCE AND TROUBLESHOOTING Inspect and tighten all parts of mild soap. See the drawing above. To clean the elliptical, use only a manufacturer-supplied regulated power adapter. 38 See assembly step 10 on the cover of direct sunlight. IMPORTANT: To avoid damage to be adjusted.
English Manual
Page 21
...the Reed Switch (60). Turn the Pulley (52) until the Drive Belt (113) is tight. See assembly step 9 on page 26. See EXPLODED DRAWING C on page 27 and EXPLODED DRAWING B on page ... two indicated M4 x 16mm Screws (97). Slide the Reed Switch (60) slightly closer to or away from the elliptical. When the reed switch is adjusted to the highest level, the drive belt may need to note the location of ... and the left roller arm. When the drive belt is aligned with the Reed Switch. 86 97 52 60 See assembly step 10 on page 27. First, remove the Right Roller Arm (39), the Right Pedal Arm (37), and...
...the Reed Switch (60). Turn the Pulley (52) until the Drive Belt (113) is tight. See assembly step 9 on page 26. See EXPLODED DRAWING C on page 27 and EXPLODED DRAWING B on page ... two indicated M4 x 16mm Screws (97). Slide the Reed Switch (60) slightly closer to or away from the elliptical. When the reed switch is adjusted to the highest level, the drive belt may need to note the location of ... and the left roller arm. When the drive belt is aligned with the Reed Switch. 86 97 52 60 See assembly step 10 on page 27. First, remove the Right Roller Arm (39), the Right Pedal Arm (37), and...
English Manual
Page 24
... 1 114 1 115 1 116 1 117 1 118 2 119 2 120 2 * - * - * - * - Drive Belt Power Adapter Lower Wire Upper Wire Pulse Wire Pulse Grip Back Pulse Grip Cap Arm Spacer Assembly Tool General White Grease Packet PTFE Grease Packet User's Manual Note: Specifications are not illustrated. 24 Description Key No. For information about ordering replacement parts...
... 1 114 1 115 1 116 1 117 1 118 2 119 2 120 2 * - * - * - * - Drive Belt Power Adapter Lower Wire Upper Wire Pulse Wire Pulse Grip Back Pulse Grip Cap Arm Spacer Assembly Tool General White Grease Packet PTFE Grease Packet User's Manual Note: Specifications are not illustrated. 24 Description Key No. For information about ordering replacement parts...