NEC P555-PT Support and Manuals
Popular NEC P555-PT Manual Pages
User Manual English - Page 5
...Equipment Classification:
Class B Peripheral
Model:
P435, P495, P555, MA431, MA491, MA551
• The intended primary use a shielded signal cable. in this manual. Failure to comply with the ... provide reasonable protection against harmful interference in a residential installation.
Responsible Party:
NEC Display Solutions of other countries. This booklet is commonly...
User Manual English - Page 18
...service.
• Regularly check the mounting location for signs of the logo ornament into the protrusion holes on a wall or ceiling and hiring a technician is detected, please refer to install the logo ornament. If a problem... in the portrait position, the logo ornament position can support the weight of qualified installation professionals. Before attaching the monitor to the wall, make...
User Manual English - Page 32
...Hz/60 Hz) or HDCP 2.2 or HDR, please set [MODE2] at [AUDIO INPUT] in the OSD or ...unable to [AUTO] or [OFF] as display drivers may not be fully
compatible and may not ...input signal is not shown. Supports HDCP (High-bandwidth Digital Contents Protection) coding, a type of digital rights ...cable, hold down the top button to different HDMI specifications. • HDCP is not shown.
See page ...
User Manual English - Page 33
... OSD menu. 3. Depending on the remote control .
2. Please refer to "Specifications" for [CEC]. 5. When supported, the monitor's remote control can be configured using the remote control.
Enabling CEC
1.
Connect a CEC device to control the HDMI media device. NOTE: The instructions in this section guide you through configuring [CEC] in , turned on a Blu-ray player...
User Manual English - Page 34
... the SET/POINT ... is set to standby using...], then press SET/ POINT ZOOM button...then press SET/POINT ZOOM.... function supports Feature Abort...supported HDMI cable.
Press the Menu button to enable CEC.
buttons to highlight [MODE1] or [MODE2], then press SET...press the SET/POINT ...SET/POINT ZOOM button...SETTINGS
DisplayPort HDMI MULTI PICTURE SIGNAL FORMAT CEC BACKGROUND COLOR VIDEO OUT SETTINGS... set ...
User Manual English - Page 35
... list in [USB] to [DISABLE].
CAUTION: Pleaser refer to use a USB cable that supports 2A. This document contains instructions for future software upgrades. Installation must be off before making connections or disconnections. Do not attempt to USB-A (Hub/0.5A) port.
Service (2A):
Service port/Power supply port. This port is for how to "CAUTION 2".
NOTE: •...
User Manual English - Page 43
... alert mail to be notified when an error occurs in "OSD Controls List" on /off schedules, set the date and time, select the languages of the default picture modes, manually adjust the color settings, adjust the aspect ratio, and adjust other settings related to an Option Board if installed. AUDIO: Adjust volume, balance, equalizer, and select...
User Manual English - Page 49
...Service (2A) port on the OSD. Or
• A near-range colorimeter with a measurement readout display in units of monitors quickly. Be sure to provide adequate access when installing...factory color measurements and those taken with the NEC MDSVSENSOR 3
color sensor. Updating the monitor's internal reference automatically updates all color settings.
• The original factory measurements can...
User Manual English - Page 50
... the instructions on... using NEC Display Wall Calibrator, uniformity adjustment data is set [1.4].
...supported color sensor device. STAND-ALONE CALIBRATION: FUNCTION SELECTION
SELF CALIBRATION RESET CALIBRATION VALIDATION WHITE COPY
LAST CALIBRATION 2020/03/03 17:15
MDSVSENSOR3: CONNECTED
Press Set key to select function
Service (2A) port USB color sensor
Self calibration
This function updates...
User Manual English - Page 58
... vertically on top: 1. One image will be divided by 4 then put number from 1 to install a video wall, communication and video cable connections are set automatically when you run the auto setup: OSD menu [H MONITORS], [V MONITORS], [POSITION], [DisplayPort VERSION], [HDMI MODE], [VIDEO OUT SETTINGS] and Input signal.
NOTE: • [MONITOR ID] in [AUTO ID/IP...
User Manual English - Page 61
...set to [ENABLE], DisplayPort1 cannot be shown due to the decision/intention of HDCP, there may stop .
• This monitor's signal output function supports...CHAIN MODE] is set to [ENABLE], HDMI... the same monitor model. • Set the same ([MODE1...set to [ENABLE], even when the OSD menu "INPUT" is set...DAISY CHAIN MODE] is set to [ENABLE], DisplayPort1...TO HDMI CONVERT] is set to [DisplayPort1] or ...
User Manual English - Page 68
.... AUTO: Automatically assign an IP address. Set your network administrator if you have any trouble.
Set for IP ADDRESS setting of the DNS server that is selected for setting the IP ADDRESS. English−64 NOTE: Consult your subnet mask data for the monitor connected to delete the setting.
MANUAL: Manually enter the IP address of DNS server...
User Manual English - Page 71
... Network Service Settings
Click on "NETWORK SERVICE" on the network when using an application such as the USER NAME when entering the password.
*What is the monitor's model name. Set a password for ...Giving the monitor a unique name allows it to the monitor.
Set a password for class2. The device supports all commands of different manufacturers. This name is only for the...
User Manual English - Page 87
...Resources
Additional specification documents ... Manual"...Setup Guide" PDF document This document describes the features, installation, connectivity, and configuration of checksums. This document is available for download from the NEC Display Solutions website in your region for download from : https://www.nec-display.com/dl/en/manual/raspberrypi/
English−83 NEC... NEC dealer or visit the NEC ...
User Manual English - Page 101
... . Shows a warning, when shutting down manually. This message cannot be turned on automatically when the monitor power is switched into the same status when the installed device is turned on . Shows the signals supported by the device installed in the option slot.
Select [YES] then press SET on the installed Option Board. If [NO] is highlighted...
NEC P555-PT Reviews
Do you have an experience with the NEC P555-PT that you would like to share?
Earn 750 points for your review!
We have not received any reviews for NEC yet.
Earn 750 points for your review!