Milwaukee Tool 2808-20 Support and Manuals
Get Help and Manuals for this Milwaukee Tool item
View All Support Options Below
Free Milwaukee Tool 2808-20 manuals!
Problems with Milwaukee Tool 2808-20?
Ask a Question
Free Milwaukee Tool 2808-20 manuals!
Problems with Milwaukee Tool 2808-20?
Ask a Question
Popular Milwaukee Tool 2808-20 Manual Pages
Operators Manual - Page 2
... specifically designated
is not in use, keep it away
the switch or energizing power tools that is are less likely to another battery pack.
•Prevent unintentional starting the power tool accidentally. •Store idle power tools out of the reach of the tool in unexpected situations. GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read tions,
all instructions...
Operators Manual - Page 3
... an electric shock. avoid contact. Safety Instructions when using only identical replacement parts. Bits can cause personal injury. •Hold power tool by the manufacturer or authorized service providers. SPECIFIC SAFETY RULES FOR RIGHT ANGLE DRILLS
Safety Instructions for all charging instructions and do not charge the battery pack or tool outside the specified range may damage the...
Operators Manual - Page 4
...tool. No 2807-20)
1. Tighten the chuck jaws by holding or bracing securely. Place the chuck key in each of the bit. No 2808-20...bit for this
specifically tool.
Remove the ...instructions, read the operator's
manual supplied with the specified for forward
rotation. Removing/Inserting the Battery To remove the battery, push in position.
Bit Selection • Use sharp bits. Installing...
Operators Manual - Page 5
... immerse
your tool, battery pack and charger in good repair by flicking the trigger switch, permitting
the bit to a MILWAUKEE service facility for...of properly bracing the tool for ALL repairs. After six months to flow inside them. Before drilling, be set to bind. When ..., changing accessories, storing the tool and any other insulated parts. If the tool does not start and to prevent...
Operators Manual - Page 6
... end-user
guide or instruction manual. This warranty applies to the ASC, along with the return product. SERVICE - CANADA Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST or visit www.milwaukeetool.ca
LIMITED WARRANTY USA & CANADA
Every MILWAUKEE power tool* (see exceptions below) is two (2) years from defects in the Parts & Service section of...
Operators Manual - Page 20
MILWAUKEE TOOL
13135 West Lisbon Road Brookfield, WI 53005 USA
58140421d1 12/19
961013430-01(B) Printed in China
Service Parts List - Page 1
...
WIRING INSTRUCTION
SEE PAGE 3
00 0
EXAMPLE: Component Parts (Small #) Are Incl. Taptite T-25 Screw 2
Rotor
1
66 45 (2x)
FIG. Tapt. WHEN ORDERING PARTS
M18 FUEL™ 7/16" Hex Hole-Hawg®
CATALOG NO. 2808-20
STARTING SERIAL NO. Right M4 x 34mm Pan Hd. Large
NO. ST T-20 Screw Handle Cover - Left Housing Halve Motor Cage Support - 13...
Service Parts List - Page 2
... output shaft with grease. Lightly coat all parts highlighted here with grease, being sure to ... armature pinion and intermediate gear assembly.
SCREW TORQUE SPECIFICATIONS
SEAT TORQUE
FIG. WHERE USED
(KG/CM) (IN/...0050 7/16" Hex Chuck (2808-20 only) 1100-1200 955-...prior to installing Type 'Y'. Use approximately .05oz. (1.5 grams).
When servicing, remove 90-95% of gearcase.
...
Service Parts List - Page 3
...the motor cage assembly to press down into handle.
3.
PRIOR TO INSTALLING THE HANDLE COVER ONTO THE HANDLE SUPPORT, BE SURE THAT THERE ARE NO INTERFERENCES.
Place the LED into...TAKE NOTICE OF WIRE ROUTING AND POSITION IN WIRE GUIDES AND TRAPS WHILE DISMANTLING TOOL.
Continue routing large red wire as shown. Be sure to handle support with black tube below the ribs. 1. Place ...
Milwaukee Tool 2808-20 Reviews
We have not received any reviews for Milwaukee Tool yet.