Miele HM 16-80 Support and Manuals
Get Help and Manuals for this Miele item
View All Support Options Below
Free Miele HM 16-80 manuals!
Problems with Miele HM 16-80?
Ask a Question
Free Miele HM 16-80 manuals!
Problems with Miele HM 16-80?
Ask a Question
Popular Miele HM 16-80 Manual Pages
Operating manual - Page 1
en - US
M.-Nr. 07 660 670 Operating Instructions Rotary Iron HM 16-80
To prevent accidents and machine damage read these instructions before installation or use.
Operating manual - Page 2
... SAFETY INSTRUCTIONS 4 Guide to the Rotary Iron 7 Moving and folding the appliance 9 Transport strut 9 Before using for the first time 11 Preparing the work area 13 Preparing the laundry 13 Testing the finger guard 14 Steam setting 15 Filling the water reservoir 15 Emptying the water reservoir 16 Ironing 17 Turning on and off 17 Selecting the ironing temperature...
Operating manual - Page 4
... only intended for the first time.
Do not install or use
~ This rotary iron is dangerous.
Turn off the rotary iron, unplug from the wall outlet and call Technical Service.
~ If the power cord is important that this basic safety requirement be followed, including the following:
Read the operating instructions carefully before using this appliance, continuity must...
Operating manual - Page 5
...iron to touch an electrical component or moving part.
~ This equipment has not been
designed for maritime use or for an installation in these applications. danger of overheating).
~ Repairs should be replaced using the rotary iron... Miele Dealer or Miele Technical Service with specific requirements. This is turned off at the wall switch and unplugged, or
- IMPORTANT SAFETY INSTRUCTIONS
...
Operating manual - Page 7
l
k j i h
g
Guide to the Rotary Iron
m
ab
c
d e
f
a Emergency release b Temperature selector c Control panel d Release catch e Power cord f Foot pedal switch g Ironing table
h Laundry rod i Feed board j Roller k Heater plate l Finger guard m Water reservoir with cap
7
Operating manual - Page 17
... selector.
Material Dot symbol
Minimum
ß
Iron
Woolens, Silk
ßß
Cotton, Linen
ßßß
I -0 button to set the ironing temperature. Selecting the ironing temperature (operation without steam)
The temperature selector is marked by dots on ^ Press the button in. To turn the rotary iron on and off ^ Press and release the button.
The indicator light...
Operating manual - Page 19
... iron: ^ Press the foot pedal all the way down to high 15 ft/min. [4.5 m/min]). A lower roller speed makes it easier to the floor.
,Do not put fingers between the
heater plate and the roller. Ironing
The ironing process is controlled by the foot pedal, which may require more than one pass through the rotary iron...
Operating manual - Page 20
... holder, then pull it is swung out, this could cause the rotary iron to tip over the swing out bar to avoid creasing.
,Take care not to press down the foot pedal.
^ Lift the feed board out of the... article to be ironed can be hel by hand. Removing the feed board
The feed board...
Operating manual - Page 21
....
-
To store the rotary iron: ^ Allow the heater plate to protect the heater plate.
- Cover zippers, metal buttons and metal hooks with a cloth, to cool. ^ Empty the water reservoir. ^ Fold the iron.
- Frozen water in a room where there is a risk of frost occurring. If needed, dampen again with raised parts, such as buttons, should...
Operating manual - Page 23
... of the fabric to the feed board. Then pass both sides. Pass handkerchiefs diagonally through the rotary iron and, if necessary, fold them and then iron again.
^ Please use the whole length of the non ironed sections through the rotary iron.
^ If needed, make one direction and then in one more pass once the tablecloth is...
Operating manual - Page 24
.... If the duvet cover has buttons at the open end has buttons, only pass it through the rotary iron if the buttons are heat-resistant.
^ Start the first run by carefully feeding this end through the rotary iron if the buttons are heat resistant.
Note: Only pass this end in first on the feeder...
Operating manual - Page 30
...rotary iron on , the heater plate heats up immediately. When the iron is at the top.
^ Turn the roller by hand in the direction you iron (see arrow) until the retaining slot is turned on .
The temperature selector must be turned to the g setting....
30
^ Press the foot pedal and "iron" the new cloth all the way around.
Cleaning and care
^ Hold the corners of the new ironing cover into the...
Operating manual - Page 31
... rise.
31
Once the roller has completed 3 or 4 revolutions and the end of the roller, tie together and tuck under the heater plate:
^ Turn the rotary iron off while keeping the foot pedal pressed down. Cleaning and care
^ Tighten the cords at the left and right-hand sides of the...
Operating manual - Page 32
... with a new machine. Possible fault
Solution
The emergency release was activated.
Frequently asked questions
,Repairs should be washed at 140°F (60°C) or replace with a new one. Lime or starch deposits on the heater plate. The rotary iron cover is soiled (lime deposits).
Creases/Folds occur
Possible fault
Solution
The heater plate is...
Operating manual - Page 35
single phase 220-240 V 60 Hz power supply (see data plate). Extension cords do not guarantee the required safety of overheating).
Do not connect the rotary iron to an a.c. danger of the appliance (e.g. The fuse rating is 20 amps.
,Do not modify the machine
power cord or plug, the machine is supplied ...
Miele HM 16-80 Reviews
We have not received any reviews for Miele yet.