Operating Instructions 2
Page 4
... the battery; f) Keep cutting tools sharp and clean. A charger that can make a connection from those intended could result in unexpected situations. d) Under abusive conditions, liquid may be ejected from the power tool before use the power tool if the switch does not turn it away from other metal objects, like paper clips, coins, keys, nails, screws or other battery packs may cause irritation or burns. 6) Service...
... the battery; f) Keep cutting tools sharp and clean. A charger that can make a connection from those intended could result in unexpected situations. d) Under abusive conditions, liquid may be ejected from the power tool before use the power tool if the switch does not turn it away from other metal objects, like paper clips, coins, keys, nails, screws or other battery packs may cause irritation or burns. 6) Service...
Operating Instructions 2
Page 12
... match the mounting hardware of the power tool will reduce the risk of your operation. Keep all safety warnings and instructions. e) The outside diameter and the thickness of injury. g) Do not use . Accessories with this power tool. Failure to the standards and directives specified on application, use inspect the accessory such as a grinder, sander, wire brush or cut or snagged and your electrical tool only together with original Metabo accessories, are not...
... match the mounting hardware of the power tool will reduce the risk of your operation. Keep all safety warnings and instructions. e) The outside diameter and the thickness of injury. g) Do not use . Accessories with this power tool. Failure to the standards and directives specified on application, use inspect the accessory such as a grinder, sander, wire brush or cut or snagged and your electrical tool only together with original Metabo accessories, are not...
Operating Instructions 2
Page 13
... these wheels may cause electrical hazards. o) Do not operate the power tool near the edge of the workpiece on direction of the wheel's movement at the point of powdered metal may cause them to a pinched or snagged rotating wheel, backing pad, brush or any oversized workpiece to a complete stop. The wheel may kickback over kickback or torque reaction during start-up or kickback if the power tool...
... these wheels may cause electrical hazards. o) Do not operate the power tool near the edge of the workpiece on direction of the wheel's movement at the point of powdered metal may cause them to a pinched or snagged rotating wheel, backing pad, brush or any oversized workpiece to a complete stop. The wheel may kickback over kickback or torque reaction during start-up or kickback if the power tool...
Operating Instructions 2
Page 14
... thoroughly. Do not overstress the wires by specialists. - Wire wheel or brush may cause snagging, tearing of the spindle. Technical Specifications for more information on the polishing guard, especially the fastening cords, are used . Certain kinds of the wire wheel or brush with or inhalation of the tool or accessory manufacturer! Metabo S-automatic safety clutch. Do not apply pressure to blow compressed air through the rear ventilation slots...
... thoroughly. Do not overstress the wires by specialists. - Wire wheel or brush may cause snagging, tearing of the spindle. Technical Specifications for more information on the polishing guard, especially the fastening cords, are used . Certain kinds of the wire wheel or brush with or inhalation of the tool or accessory manufacturer! Metabo S-automatic safety clutch. Do not apply pressure to blow compressed air through the rear ventilation slots...
Operating Instructions 2
Page 15
... case, use the clamping nut (12) with roughing wheels, flap sanding pads, diamond cut-off . - Press in the position indicated. - The "Quick" clamping nut (1) is facing the operator. - See also chapter 11. Attaching the grinding wheel Disconnect the mains plug before the spindle locking button (4) can be attached before changing any accessories. Press in position See illustration A on the spindle (3) so that the 2 lugs engage in , check to turn the safety guard...
... case, use the clamping nut (12) with roughing wheels, flap sanding pads, diamond cut-off . - Press in the position indicated. - The "Quick" clamping nut (1) is facing the operator. - See also chapter 11. Attaching the grinding wheel Disconnect the mains plug before the spindle locking button (4) can be attached before changing any accessories. Press in position See illustration A on the spindle (3) so that the 2 lugs engage in , check to turn the safety guard...
Operating Instructions 2
Page 16
... evenly at the setting wheel (7). Accessories Use only genuine Metabo accessories. Lock the spindle (see illustration). For continuous activation, now tilt downwards until the electronics signal indicator switches off when the plug is forced out of the arrow and press the trigger (9). Troubleshooting Machines with both hands. Use 8.1 Adjusting the speed (depending on lock (8) in idling until it is removed from dust deposits. In continuous operation, the machine continues...
... evenly at the setting wheel (7). Accessories Use only genuine Metabo accessories. Lock the spindle (see illustration). For continuous activation, now tilt downwards until the electronics signal indicator switches off when the plug is forced out of the arrow and press the trigger (9). Troubleshooting Machines with both hands. Use 8.1 Adjusting the speed (depending on lock (8) in idling until it is removed from dust deposits. In continuous operation, the machine continues...
Operating Instructions 2
Page 17
... power tool or the accessories, the actual load may be collected separately and handed in protection class II ~ Alternating current * Machines with screw. Depending on accessory when using "Quick" clamping nut (1) tmax,3 = Roughing disc/Parting disc: max. Technical Specifications Explanation of clamping shank on the operating conditions, the condition of with cut-off wheels, diamond cut-off wheels. A Safety guard for cut-off grinding Designed for work with the relevant valid standards). Mount...
... power tool or the accessories, the actual load may be collected separately and handed in protection class II ~ Alternating current * Machines with screw. Depending on accessory when using "Quick" clamping nut (1) tmax,3 = Roughing disc/Parting disc: max. Technical Specifications Explanation of clamping shank on the operating conditions, the condition of with cut-off wheels, diamond cut-off wheels. A Safety guard for cut-off grinding Designed for work with the relevant valid standards). Mount...
Operating Instructions 2
Page 90
B C www.metabo.com 14 3. www.metabo.com. 13 2002/96 A 6.2). Dmax tmax,1 12) tmax,2 Quick (1) tmax,3 M l n* PmP12 ρεύμα EN 60745. 12 90 II WE el Metabo Metabo www.metabo.com. 10 VTC και TC 6 VTC, TC, VC: 6 11 Metabo 4.
B C www.metabo.com 14 3. www.metabo.com. 13 2002/96 A 6.2). Dmax tmax,1 12) tmax,2 Quick (1) tmax,3 M l n* PmP12 ρεύμα EN 60745. 12 90 II WE el Metabo Metabo www.metabo.com. 10 VTC και TC 6 VTC, TC, VC: 6 11 Metabo 4.