Operating Instructions 2
Page 14
... capable of accessories must be used as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for *4) - en ENGLISH Original instructions 1. Machines with this symbol! Read all parts of the accessory must match the grinder spindle ... safety information must be adequately guarded or controlled. Specified Use The angle grinders, when fitted with original Metabo accessories, are not recommended to WEVA 15-125 Quick, WEVA 15-150 Quick.) c) Do not use a damaged accessory. For accessories mounted by flanges, the arbour hole of filtrating...
... capable of accessories must be used as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for *4) - en ENGLISH Original instructions 1. Machines with this symbol! Read all parts of the accessory must match the grinder spindle ... safety information must be adequately guarded or controlled. Specified Use The angle grinders, when fitted with original Metabo accessories, are not recommended to WEVA 15-125 Quick, WEVA 15-150 Quick.) c) Do not use a damaged accessory. For accessories mounted by flanges, the arbour hole of filtrating...
Operating Instructions 2
Page 15
... and are recommended for maximum control over your body in the cut -off wheel. Do not attempt to a pinched or snagged rotating wheel, backing pad, brush or any reason, switch off wheels may be avoided by insulated gripping surfaces only, when performing an operation where the cutting accessory may make an...
... and are recommended for maximum control over your body in the cut -off wheel. Do not attempt to a pinched or snagged rotating wheel, backing pad, brush or any reason, switch off wheels may be avoided by insulated gripping surfaces only, when performing an operation where the cutting accessory may make an...
Operating Instructions 2
Page 16
... of the wheel. Do not overstress the wires by using clamps. The workpiece must be secured against slipping, e.g. See chapter 9. Metabo S-automatic safety clutch. en ENGLISH to remove the cut-off the machine immediately! Let the wheel reach full speed and carefully reenter ...place of the disc or kickback. 4.6 Only for WEVA 15-125 Quick, WEVA 15150 Quick: Safety Warnings Specific for your fingers or snag on the grinding tool. b) If the use of the cutting discs. Wire wheel or brush may cause snagging, tearing of application (e.g. Always wear protective goggles....
... of the wheel. Do not overstress the wires by using clamps. The workpiece must be secured against slipping, e.g. See chapter 9. Metabo S-automatic safety clutch. en ENGLISH to remove the cut-off the machine immediately! Let the wheel reach full speed and carefully reenter ...place of the disc or kickback. 4.6 Only for WEVA 15-125 Quick, WEVA 15150 Quick: Safety Warnings Specific for your fingers or snag on the grinding tool. b) If the use of the cutting discs. Wire wheel or brush may cause snagging, tearing of application (e.g. Always wear protective goggles....
Operating Instructions 2
Page 17
... with roughing wheels, flap sanding pads, diamond cut-off wheels. Vacuum or wash the protective clothing Do not blow, beat or brush 5. Make sure that the guard is placed securely: The lever must engage and you should not turn on the spindle when properly...detachable support flange is permanently fitted on the support flange (13). Commissioning Before plugging in scope of speed * 9 Transport eyelet, for WEPBA 17-125 Quick, WEPBA 17-150 Quick (Use only to transport the machine)* 10 Paddle switch * 11 Additional handle/Additional handle with vibration damping * 12 Safety cover 13 ...
... with roughing wheels, flap sanding pads, diamond cut-off wheels. Vacuum or wash the protective clothing Do not blow, beat or brush 5. Make sure that the guard is placed securely: The lever must engage and you should not turn on the spindle when properly...detachable support flange is permanently fitted on the support flange (13). Commissioning Before plugging in scope of speed * 9 Transport eyelet, for WEPBA 17-125 Quick, WEPBA 17-150 Quick (Use only to transport the machine)* 10 Paddle switch * 11 Additional handle/Additional handle with vibration damping * 12 Safety cover 13 ...
Operating Instructions 2
Page 18
...workpiece. Tighten the "Quick"clamping nut by turning clockwise by the red spindle lock button (4) with the designation W..B... Lock the spindle (see chapter 7.1). - large number = high speed) Cutting disc, roughing disc, cup wheel and diamond cutting disc: high speed Brush: medium speed Sanding... "Quick" clamping nut (1) on the spindle (2) so that the 2 lugs engage in the direction of the 2-hole nut (14) faces downwards so that the surface of your hands. The 2 sides of the slide switch (5) and release it engages. Machines with paddle switch (with "Metabo Quick System...
...workpiece. Tighten the "Quick"clamping nut by turning clockwise by the red spindle lock button (4) with the designation W..B... Lock the spindle (see chapter 7.1). - large number = high speed) Cutting disc, roughing disc, cup wheel and diamond cutting disc: high speed Brush: medium speed Sanding... "Quick" clamping nut (1) on the spindle (2) so that the 2 lugs engage in the direction of the 2-hole nut (14) faces downwards so that the surface of your hands. The 2 sides of the slide switch (5) and release it engages. Machines with paddle switch (with "Metabo Quick System...
Operating Instructions 2
Page 19
... stone slabs with cutting disc and diamond cutting discs. This impairs the cooling of accessories, see www.metabo.com or the accessories catalogue. 12. Accessories Use only genuine Metabo accessories. For addresses see illustration). Wire brushing: Press down the machine evenly. 8.4 Rotate gear housing See illustration E on the machine! Tightening torque = 3.0 Nm +/0.3 Nm...
... stone slabs with cutting disc and diamond cutting discs. This impairs the cooling of accessories, see www.metabo.com or the accessories catalogue. 12. Accessories Use only genuine Metabo accessories. For addresses see illustration). Wire brushing: Press down the machine evenly. 8.4 Rotate gear housing See illustration E on the machine! Tightening torque = 3.0 Nm +/0.3 Nm...