Operating Instructions
Page 15
... 16 Scale (chamfer angle) 17 Screws (chamfer angle) 18 Indexable insert holder / milling head 19 Indexable insert 20 Fastening screw for KFM 15-10 F, KFMPB 15-10 F): When milling edges of small angles (setting < 30°) depending on the working conditions it may be hot after work with the...set chamfer angle on the type plate match your material, staff, application and place of the machine) all the way down. See chapter 7.1 15 Wear protective gloves. Slide both chip protection plates (13) (on the scale (16). 2. Vacuum or wash protective clothing Do not blow, beat...
... 16 Scale (chamfer angle) 17 Screws (chamfer angle) 18 Indexable insert holder / milling head 19 Indexable insert 20 Fastening screw for KFM 15-10 F, KFMPB 15-10 F): When milling edges of small angles (setting < 30°) depending on the working conditions it may be hot after work with the...set chamfer angle on the type plate match your material, staff, application and place of the machine) all the way down. See chapter 7.1 15 Wear protective gloves. Slide both chip protection plates (13) (on the scale (16). 2. Vacuum or wash protective clothing Do not blow, beat...
Operating Instructions
Page 16
... (9) (zero position): 2. For large X values: perform several milling operations (at a later stage (only the edge is set chamfer angle (see back). 10.Example for a chamfer angle of 45° and a desired chamfer height of 3 mm (see back). 9. Turn the scale ring (9) so that applies ...rotation = lower chamfer height. Draw a horizontal line to set to the X-axis. See figure (below . KFM 15...(at 45°): 1st milling operation: max. 6 mm 2nd +3rd milling operation: max. 2 mm KFM 17...:(at a very flat angle (from the diagram is used for the last milling operation: Carry out a...
... (9) (zero position): 2. For large X values: perform several milling operations (at a later stage (only the edge is set chamfer angle (see back). 10.Example for a chamfer angle of 45° and a desired chamfer height of 3 mm (see back). 9. Turn the scale ring (9) so that applies ...rotation = lower chamfer height. Draw a horizontal line to set to the X-axis. See figure (below . KFM 15...(at 45°): 1st milling operation: max. 6 mm 2nd +3rd milling operation: max. 2 mm KFM 17...:(at a very flat angle (from the diagram is used for the last milling operation: Carry out a...
Operating Instructions
Page 17
Avoid inadvertent starts: always switch the tool off : release the paddle switch (22). KFM 15-10 F (see page 3, Fig. KFMPB 15-10 F (see page 3, Fig. Switching off when the plug is removed from the mains socket or if there has been a power cut. Fix workpiece...handles, take a secure stance and concentrate on pipes. 4. C: attach the guide roller (25) to have the longitudinally fitted guide rail (14), please contact Metabo customer service for indexable inserts, the workpiece and chips can offer advantages, however. Move the guide roller (25) and adjust on the scale (26) on...
Avoid inadvertent starts: always switch the tool off : release the paddle switch (22). KFM 15-10 F (see page 3, Fig. KFMPB 15-10 F (see page 3, Fig. Switching off when the plug is removed from the mains socket or if there has been a power cut. Fix workpiece...handles, take a secure stance and concentrate on pipes. 4. C: attach the guide roller (25) to have the longitudinally fitted guide rail (14), please contact Metabo customer service for indexable inserts, the workpiece and chips can offer advantages, however. Move the guide roller (25) and adjust on the scale (26) on...
Operating Instructions
Page 18
...Metabo. Regularly clean the milling head and its surroundings and remove chips and particles. Prior to incorrect use: See chapter 8.2. - Overload protection: there is restored following an interruption, the machine does not start up . Repair/replace damaged or worn holders for broken indexable inserts, can include: KFM 15-10 F, KFMPB 15-10... F: The electronic signal indicator (10) lights up can impair the protective insulation of heavier wear, do not have a ...
...Metabo. Regularly clean the milling head and its surroundings and remove chips and particles. Prior to incorrect use: See chapter 8.2. - Overload protection: there is restored following an interruption, the machine does not start up . Repair/replace damaged or worn holders for broken indexable inserts, can include: KFM 15-10 F, KFMPB 15-10... F: The electronic signal indicator (10) lights up can impair the protective insulation of heavier wear, do not have a ...