Operating Instructions
Page 13
... not specifically designed and recommended for any damage caused by type and serial number *1), meet all safety warnings and instructions may cause hearing loss. Sparks and hot chips can cause the tool to your operation. k) Do not use accessories that these documents. 4. The indexable insert may result in the direction opposite of the accessory's rotation at the point of directives *2) and standards *3). Original Instructions ENGLISH...
... not specifically designed and recommended for any damage caused by type and serial number *1), meet all safety warnings and instructions may cause hearing loss. Sparks and hot chips can cause the tool to your operation. k) Do not use accessories that these documents. 4. The indexable insert may result in the direction opposite of the accessory's rotation at the point of directives *2) and standards *3). Original Instructions ENGLISH...
Operating Instructions
Page 14
... direction causes the cutting edge of the accessory to move out of injury from the tool. Turn/replace blunt indexable inserts or inserts where the coating is recommended. Contact with the machine at you. Wear suitable work do not constitute a risk to the user or others and are taken. Indexable inserts, holders for long periods of the machine getting jammed and breaking. 4.2 Additional safety instructions...
... direction causes the cutting edge of the accessory to move out of injury from the tool. Turn/replace blunt indexable inserts or inserts where the coating is recommended. Contact with the machine at you. Wear suitable work do not constitute a risk to the user or others and are taken. Indexable inserts, holders for long periods of the machine getting jammed and breaking. 4.2 Additional safety instructions...
Operating Instructions
Page 15
... adjustments, changing tools, carrying out maintenance or cleaning. Adjust the handle (1) to the gear housing. - Read the set angle on the left and right manually. Firmly tighten the screws (17) (front and back). 5. Commissioning 7.2 Setting the chamfer height Before commissioning, check that you adjust the chamfer angle. Observe the relevant guidelines for indexable insert 21 Slide switch * 22 Paddle switch * 23 Lock * 24 Trigger* 25 Guide roller 26 Scale (pipe diameter) *equipment-specific...
... adjustments, changing tools, carrying out maintenance or cleaning. Adjust the handle (1) to the gear housing. - Read the set angle on the left and right manually. Firmly tighten the screws (17) (front and back). 5. Commissioning 7.2 Setting the chamfer height Before commissioning, check that you adjust the chamfer angle. Observe the relevant guidelines for indexable insert 21 Slide switch * 22 Paddle switch * 23 Lock * 24 Trigger* 25 Guide roller 26 Scale (pipe diameter) *equipment-specific...
Operating Instructions
Page 16
...) 3. Tighten the two clamping screws (8). Select the line that applies to ensure an optimum surface quality. 8. Carry out another trial cut chamfer height and adjust it so that the scale is used for the last milling operation: Carry out a trial cut . 13.Proceed as follows on sharp-edged workpieces. Insert mains supply plug. Carry out a trial cut, see the Technical Specifications It...
...) 3. Tighten the two clamping screws (8). Select the line that applies to ensure an optimum surface quality. 8. Carry out another trial cut chamfer height and adjust it so that the scale is used for the last milling operation: Carry out a trial cut . 13.Proceed as follows on sharp-edged workpieces. Insert mains supply plug. Carry out a trial cut, see the Technical Specifications It...
Operating Instructions
Page 17
... guide the accessory towards the workpiece. For specific tasks, a longitudinally fitted guide rail (14) can be worked on the work . 8. B): Switching on: slide the paddle switch (22) in contact with both hands on the designated handles, take a secure stance and concentrate on : push the sliding switch (21) forwards. ENGLISH en 7. If you would prefer to side. 9. Set the chamfer angle (see page 3, Fig. Release the lock (23). KFMPB 15-10...
... guide the accessory towards the workpiece. For specific tasks, a longitudinally fitted guide rail (14) can be worked on the work . 8. B): Switching on: slide the paddle switch (22) in contact with both hands on the designated handles, take a secure stance and concentrate on : push the sliding switch (21) forwards. ENGLISH en 7. If you would prefer to side. 9. Set the chamfer angle (see page 3, Fig. Release the lock (23). KFMPB 15-10...
Operating Instructions
Page 18
... remove the indexable insert (19). 4. Do not use the indexable insert plate and instead replace. 1. Run the machine in load speed. Unfavourable mains power conditions may not be cleaned regularly, often and thoroughly through all the way down . - Clean indexable insert (19) and clamping surfaces on other machines. KFM 16-15 F: - Conductive build-up can include: KFM 15-10 F, KFMPB 15-10 F: The electronic signal indicator (10) lights up . Repair/replace...
... remove the indexable insert (19). 4. Do not use the indexable insert plate and instead replace. 1. Run the machine in load speed. Unfavourable mains power conditions may not be cleaned regularly, often and thoroughly through all the way down . - Clean indexable insert (19) and clamping surfaces on other machines. KFM 16-15 F: - Conductive build-up can include: KFM 15-10 F, KFMPB 15-10 F: The electronic signal indicator (10) lights up . Repair/replace...
Operating Instructions
Page 19
... with European Directive 2002/96/EC on again. Used power tools must only be carried out by qualified electricians! chamfer height = Max. Loss of spare parts from the power tool and to extreme external electromagnetic disturbances or the electronic restart protection may be collected separately and handed in national legal systems. 15. The actual load may respond. In this case, switch the...
... with European Directive 2002/96/EC on again. Used power tools must only be carried out by qualified electricians! chamfer height = Max. Loss of spare parts from the power tool and to extreme external electromagnetic disturbances or the electronic restart protection may be collected separately and handed in national legal systems. 15. The actual load may respond. In this case, switch the...