Maytag UVL6036J Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag UVL6036J manuals!
Problems with Maytag UVL6036J?
Ask a Question
Free Maytag UVL6036J manuals!
Problems with Maytag UVL6036J?
Ask a Question
Popular Maytag UVL6036J Manual Pages
Installation Instructions - Page 5
....
Check that are included. ■ 3 metal grease filters ■ Hood liner with halogen lamps installed. ■ 1 - 10" (25.4 cm) square to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for 48" models
Hood support must be sealed.
Suggested maximum distance "X": 36" (91.4 cm).
†®TORX and...
Installation Instructions - Page 8
...Hood Liner Support Preparation
1. Wall B. Drill a 11/4" (3.2 cm) hole at this location.
4. Install the ...parts in the blower motor installation packet that surface. See the "Install Range Hood Internal Blower Motor" section and the instructions supplied with damper to move and install range hood. Using a 1/8" (3 mm) drill bit, drill the four holes.
8
INSTALLATION INSTRUCTIONS...
Installation Instructions - Page 9
...of mounting holes for the dual motor system. Motor support bracket D. Install the 6 mm nuts to the outside top or outside set of the square vent opening . ■ Five...(alternate location on some models) of the spring clip through the slot in the Use and Care Guide.
2. Motor spring clip (dual motor assembly location) 4.
Install the motor support bracket using four mounting ...
Installation Instructions - Page 11
... motor system. Plywood may be strong enough to support the weight of the in -line blower motor housing... the mounting location.
2. D
A. Motor electrical plug
Install In-line Blower System
NOTE: The blower motor housing ... 10 screws from either an internal type or an in -line blower housing and set them aside.
3. Mounting holes
1. Power supply connector from the range hood to ...
Installation Instructions - Page 12
... at this location.
4.
Replace all joints with clamps. Leave... gray wires (G) together.
12 Remove the terminal box covers and set the covers and screws aside. Electrical knockout
5. Electrical Connection Inside ...parts and panels before servicing.
White wires E. Use UL listed wire connectors and connect the blue wires (F) together.
7. Make Electrical Connections for the installation...
Installation Instructions - Page 15
... the Fan
1. Light control B. Move the light switch to the "1" position to night light setting.
2. Move the fan switch to the off position to turn range hood light to turn the... protector to restart the range hood.
15 When the heat decreases, the fan will begin operating at the speed set on Fan
A
B
C
A.
Move the light switch to the "Off" position to "1" position for low ...
Installation Instructions - Page 16
... place.
4. Metal Grease Filter:
1. Repeat steps 2-3 for the other lamp if needed in spring-release handle.
5.
Replace grease filters before calling service.
1. Turn off the range hood and allow the halogen lamp to the following instructions. Wash metal filters as needed .
5. Turn it clockwise to the exterior surface, do not touch lamp with...
Installation Instructions - Page 18
....
■ Features and specifications on our full line of appliances.
■ Referrals to order replacement parts, we recommend that you need replacement parts If you use in your nearest designated service center.
Accessories
Stainless Steel Grease Filter - kit contains one filter Order Part Number W10351855 Order quantity 3 for 36" (91.4 cm) model Order quantity 4 for 48...
Owners Manual - Page 5
... location should be capable of supporting 75 lb (34 kg)
"X" bottom of canopy to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes. Grounded electrical outlet is...
Owners Manual - Page 6
... Air
Local building codes may require the use 4" (10.2 cm) laundry-type wall caps. ■ Use metal vent only. A. 10" (25.4 cm) round vent B. Roof cap
A. 10" (25.4 cm) round vent B. Venting Methods
Typical Internal Blower Motor System Venting Installations
A 10" (25.4 cm) round vent system is needed for specific requirements in the...
Owners Manual - Page 8
...INSTALLATION INSTRUCTIONS... Failure to make all installation parts have been removed from ...installation packet that surface. See the "Range Hood Care" section.
Hood Liner Support...installed 24" (61.0 cm) minimum for electric cooking surfaces, 30" (76.2 cm) minimum for the upper hood liner housing as shown. Drill a 11/4" (3.2 cm) hole at this location.
4. Remove terminal box cover and set...
Owners Manual - Page 9
...supporting 75 lb
(34 kg).
1. Install the motor support bracket using four 5 x 45 mm screws to the hood support and tighten securely. Screw spring clip to the inside top or back (alternate location on some models), toward the left side of the hood liner. Motor support... Motor System" in the Use and Care Guide.
2.
Screw bracket to the inside set of the square vent opening . ■...
Owners Manual - Page 11
...WARNING
Excessive Weight Hazard
Use two or more people, move and install in this section.
4. If you to the in -line blower motor housing and set them aside.
3. Mounting holes
1. Remove the front cover of... This structure must span the studs. Failure to support the weight of the roof, ceiling, wall, floor, or new or existing frame construction. Bottom housing mounting holes ...
Owners Manual - Page 12
... box covers and set the covers and ...Green (or yellow/green) and green/yellow wires
I
A. Replace all parts and panels before servicing. Determine the location where the 1/2" (13 mm) wiring conduit... wire length in -line blower housing and hood liner electrical terminal boxes.
9. Gray wires
H. Install the conduit connectors and conduit to the in each terminal box to the terminal boxes in the...
Owners Manual - Page 18
...
If you use in your nearest designated service center. Our consultants provide assistance with :
■ Scheduling of appliances.
■ Referrals to order replacement parts, we recommend that you have any questions or concerns at 1-800-422-1230.
■ Use and maintenance procedures. ■ Accessory and repair parts sales.
Order Model Number UXB1200DYS 600 CFM In-Line...
Maytag UVL6036J Reviews
We have not received any reviews for Maytag yet.