Maytag MGDB725BW Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag MGDB725BW manuals!
Problems with Maytag MGDB725BW?
Ask a Question
Free Maytag MGDB725BW manuals!
Problems with Maytag MGDB725BW?
Ask a Question
Most Recent Maytag MGDB725BW Questions
Check Lint Light Comes On
My Maytag MGDB725BW0 is not working properly. When ready to start the dryer the led reads 40 minutes...
My Maytag MGDB725BW0 is not working properly. When ready to start the dryer the led reads 40 minutes...
(Posted by eid00 4 years ago)
Is There A Replaceable Timer For This
My Maytag MGDB725BW dryer is heating ok but the timer display jumps from 40 to 42 minuteswhen I hit ...
My Maytag MGDB725BW dryer is heating ok but the timer display jumps from 40 to 42 minuteswhen I hit ...
(Posted by eid00 4 years ago)
Maytag MGDB725BW Videos
Maytag MGDB725BW Front Load Dryer
Duration: :58
Total Views: 90
Duration: :58
Total Views: 90
Popular Maytag MGDB725BW Manual Pages
Dimension Guide - Page 1
...Gas Dryer
PRODUCT MODEL NUMBERS MGDB700B, MGDB725B, MGDB880B, MGDB980B
DRYER DIMENSIONS
Models with riser
Bottom view:
Side view Models without riser
Back view
NOTE: Most installations require a minimum 5" (102 mm) clearance behind the dryer for wall, door, and floor moldings.
■■ Additional spacing should also be considered on all sides of the dryer... installation and servicing....
Dimension Guide - Page 2
... specified in Vent System Chart.
Specifications subject to the gas supplier and local codes, 3/8" approved tubing may be installed within 6 ft (1.8 m) of elbows and
turns. ■■ When using new inlet hoses. gas. When acceptable to change materials and specifications without notice. WATER (STEAM MODELS ONLY) REQUIREMENTS
The dryer must be used for planning purposes...
Installation Guide - Page 4
... hex-head socket wrench
Level
Vent clamps
Pipe-joint compound resistant to the "Assistance or Service" section in your dryer.
Tools needed for all installations:
Tools needed : (Not supplied with riser
Leveling legs (4) for models with dryer) Check local codes. Parts needed for gas installations:
8" (203 mm) or 10" (254 mm) pipe wrench
8" (203 mm) or 10" (254 mm...
Installation Guide - Page 5
... your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of 1" (25 mm) under entire dryer.
See "Venting Requirements."
5 Models without riser
Side view Bottom view:
Back view
NOTE: Most installations require a minimum of an automatic sensor cycle. NOTE: No other fuel-burning appliance can...
Installation Guide - Page 8
... Installation Code. E C
A
D
B
A. 3/8" flexible gas connector B. 3/8" pipe to avoid kinking. ■■ Use only pipe-joint compound. NOTE: Pipe-joint compounds that resist the action of your dryer
has a 3/8" male pipe thread. DRYER GAS PIPE ■■ The gas pipe that complies with a different gas without consulting your dryer has been converted to reach for gas appliances...
Installation Guide - Page 10
... and supported in final dryer location. ■■ Remove excess to seal all governing codes and ordinances. Replace plastic ...Guide."
10 Do not use plastic or metal foil vent. Vent products can be purchased from entire length of fire, this dryer MUST BE
EXHAUSTED OUTDOORS. Dryer exhaust must not be used for best drying performance and to achieve best drying performance. Review...
Installation Guide - Page 15
... on top of its first cycle. All Models:
q Select a Timed Dry heated cycle, and start of dryer or work space
to the need for certain part replacement or repair.
Install 4 plastic plugs (A) into a grounded outlet. q Be sure the water faucets are now installed.
Excessive scale buildup may clog different parts of the two hinges
in your door...
Warranty Information - Page 1
... "Maytag") will need repair service, first see the "Troubleshooting" section of the Use & Care Guide. Replacement parts or repair labor on the product. EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
Replacement parts or repair labor if this major appliance is not installed in...
Use & Care Guide - Page 4
... dry garments. Service calls caused by improper venting are sensed in a vent system;
Use Sensor cycles for better fabric care and energy savings
Use the Sensor Cycles to follow the "Installation Instructions" supplied with your steam dryer
n Results may vary depending on clothes. With Timed Cycles, the dryer runs the amount of time set and sometimes...
Use & Care Guide - Page 11
... on inside of the drying rack. Locate the light bulb cover on top of the dryer drum. Place wet items on the
back wall of the cover. Select a Timed Dry/Air Only, or Low Temperature cycle. Start the dryer. Replace the bulb with the screw.
4. Replace all parts and panels before servicing. Open the dryer door. Allow space around...
Use & Care Guide - Page 13
... pipe. 4. Use tape to secure dryer door. Make sure leveling legs are at home.
Clean lint screen. Replace all parts and panels before servicing. Reinstalling the Dryer Follow the "Installation Instructions" to reduce the risk of time, you will not freeze. To Use the Dryer Again 1.
WARNING
SPECIAL INSTRUCTIONS FOR STEAM MODELS
Water Inlet Hose Replace inlet hose and hose screen...
Use & Care Guide - Page 14
...Installation Instructions". See "Level the Dryer" in dryer. dried. The load is clogged with heavy metal or flexible metal vent. TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.maytag... household fuses or circuit breakers. If the problem continues, call an electrician.
Check with lint.
For gas dryers, make this noise even with a qualified ...
Use & Care Guide - Page 15
... connected to both the faucet and dryer's water inlet valve.
Closet doors must have ventilation openings at the top and bottom of the cycle. See "Installation Instructions". Clothes are ending early. Clean lint screen before each load.
These will change the amount of garments to possibly avoid a service call. Select Auto or Custom Refresh...
Use & Care Guide - Page 16
... to the estimated time remaining. Allow the dryer to "Installation Instructions" for details. Electric dryers use two household fuses or breakers.
"L2" Diagnostic Code (low or no line voltage condition)
There may be a problem with a high temperature setting. Confirm the power cord is present. The dryer will continue to possibly avoid a service call.
If you experience
Possible Causes...
Use & Care Guide - Page 17
... parts or repair labor if this major appliance is used in the country in which it is installed in -warranty service. Some states and provinces do not allow limitations on major appliances with original model/serial numbers that vary from accident, alteration, misuse, abuse, fire, flood, acts of your authorized Maytag dealer to resolve
the problem after checking "Troubleshooting...
Maytag MGDB725BW Reviews
We have not received any reviews for Maytag yet.