Installation Guide
Page 4
... (all parts are included. Parts needed for gas installations: 8" or 10" pipe wrench 8" or 10" adjustable wrench (for all installations: Tools needed : (Not supplied with a pedestal or a stack kit. NOTE: Do not use leveling legs supplied with dryer if installing with dryer) ■■Vent clamps ■■Vent elbows and...
... (all parts are included. Parts needed for gas installations: 8" or 10" pipe wrench 8" or 10" adjustable wrench (for all installations: Tools needed : (Not supplied with a pedestal or a stack kit. NOTE: Do not use leveling legs supplied with dryer if installing with dryer) ■■Vent clamps ■■Vent elbows and...
Installation Guide
Page 5
... or stored in an area where it will need 18" (460 mm) to bottom of automatic sensor cycles, resulting in longer drying times. If using a pedestal, you will need : ■■A location allowing for an electric dryer. ■■If using the supplied "Y" connector and a short hose (which you will be...
... or stored in an area where it will need 18" (460 mm) to bottom of automatic sensor cycles, resulting in longer drying times. If using a pedestal, you will need : ■■A location allowing for an electric dryer. ■■If using the supplied "Y" connector and a short hose (which you will be...
Installation Guide
Page 9
... corner post from dryer packaging under entire back edge of the burner Btu rating shown on the model/serial number plate is mounted on the pedestal model. Prepare dryer for leveling legs DRYER GAS PIPE ■■The gas pipe that complies with a listed flexible gas connector that comes ...out through the rear of cardboard from the floor, depending on a pedestal, the gas pipe height must be an additional 10" (254 mm) or 15.5" (394 mm) from dryer carton; To avoid damaging floor, use a ...
... corner post from dryer packaging under entire back edge of the burner Btu rating shown on the model/serial number plate is mounted on the pedestal model. Prepare dryer for leveling legs DRYER GAS PIPE ■■The gas pipe that complies with a listed flexible gas connector that comes ...out through the rear of cardboard from the floor, depending on a pedestal, the gas pipe height must be an additional 10" (254 mm) or 15.5" (394 mm) from dryer carton; To avoid damaging floor, use a ...
Use & Care Guide
Page 4
Stack Kit If space is at 1-800-901-2042, or visit: www.maytag.com/accessories. For more information on top of the washer. Drying Rack The Drying Rack provides a stationary drying surface for more comfortable working height. See ... kit allows the dryer to a more information. 4 The large drawer provides convenient storage. ACCESSORIES Customize your dealer, call 1-800-807-6777, or visit: www.maytag.ca 15" Pedestal Color-matched pedestals raise the washer and dryer to be installed on options and ordering, contact your new washer and dryer with the following genuine...
Stack Kit If space is at 1-800-901-2042, or visit: www.maytag.com/accessories. For more information on top of the washer. Drying Rack The Drying Rack provides a stationary drying surface for more comfortable working height. See ... kit allows the dryer to a more information. 4 The large drawer provides convenient storage. ACCESSORIES Customize your dealer, call 1-800-807-6777, or visit: www.maytag.ca 15" Pedestal Color-matched pedestals raise the washer and dryer to be installed on options and ordering, contact your new washer and dryer with the following genuine...
Installation Guide
Page 3
... legs supplied with dryer if installing with dryer) Refer to the dryer must end in dryer drum. Check local codes. Optional Equipment: (Not supplied with a pedestal or a stack kit. The wires that all models): Leveling legs (4) Parts supplied (steam models): Flat-blade screwdriver #2 Phillips screwdriver "Y" connector 2' (0.6 m) inlet hose Wire stripper (direct...
... legs supplied with dryer if installing with dryer) Refer to the dryer must end in dryer drum. Check local codes. Optional Equipment: (Not supplied with a pedestal or a stack kit. The wires that all models): Leveling legs (4) Parts supplied (steam models): Flat-blade screwdriver #2 Phillips screwdriver "Y" connector 2' (0.6 m) inlet hose Wire stripper (direct...
Installation Guide
Page 4
... cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves and water pressure of 5" (127 mm) clearance behind dryer for your washer using a pedestal, you will be exposed to bottom of automatic sensor cycles, resulting in an area where it will need 18" (460 mm) to water and/or...
... cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves and water pressure of 5" (127 mm) clearance behind dryer for your washer using a pedestal, you will be exposed to bottom of automatic sensor cycles, resulting in an area where it will need 18" (460 mm) to water and/or...