Maytag MED5630HW Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag MED5630HW manuals!
Problems with Maytag MED5630HW?
Ask a Question
Free Maytag MED5630HW manuals!
Problems with Maytag MED5630HW?
Ask a Question
Most Recent Maytag MED5630HW Questions
Med5630hw Vent Location
I'm building a new wall to put this dryer on top of a MHW5630HW washer. Can you provide a spec sheet...
I'm building a new wall to put this dryer on top of a MHW5630HW washer. Can you provide a spec sheet...
(Posted by lvroegin 2 years ago)
Popular Maytag MED5630HW Manual Pages
Installation Instructions - Page 4
... legs supplied with dryer if installing with dryer): ■■ Vent clamps ■■ Vent elbows and vent work Parts needed (not supplied with a pedestal or a stack kit. Check that opens to propane gas
Parts supplied (all models):
Tape measure
Pliers
Utility knife
Tin snips (new vent installations)
Leveling legs (4) Parts needed for gas installations:
Flat-blade screwdriver...
Installation Instructions - Page 5
... 20-120 psi (138-827 kPa). LOCATION REQUIREMENTS
Check code requirements. DRYER DIMENSIONS Front view:
Side view: Whirlpool® Models
You will be installed or stored in ring terminals or spade terminals with dryer): Refer to your Use and Care Guide for information about accessories available for proper exhaust installation. See "Venting Requirements."
■■ A separate 15 or 20...
Installation Instructions - Page 6
... top and bottom of installation and servicing.
■■ Additional clearances might be required for straight back venting only. Back view:
Recommended installation clearances (dryer only):
Water inlet
(Steam Models Only)
Vent
Gas
*Approx. measurement
NOTE: Most installations require a minimum of gas dryers:
■■ Mobile Home Installation Hold-down Kit Part Number 346764 is...
Installation Instructions - Page 9
...contact your Use and Care Guide. Securely tighten all gas ...Canada: An individual manual shut-off valve...dryer is equipped for
lengths under 20 ft. (6.1 m) if local codes and gas supplier permit.
■■ If you are using natural gas, do so can be installed within six (6) ft. (1.8 m) of your dealer or call the phone numbers referenced in the "Assistance or Service" section of the dryer...
Installation Instructions - Page 10
...it is mounted on a pedestal, the gas pipe height...installed above 2,000 ft. (610 m) a 4% reduction of cardboard from the floor, depending on the model/serial number plate is no longer visible. GAS SUPPLY CONNECTION REQUIREMENTS
■■ Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting between the flexible gas connector and the dryer gas pipe, as needed to connect the exhaust vent...
Installation Instructions - Page 17
...threads of propane gas.
MAKE GAS CONNECTION
(Gas models only)
WARNING
2. A recommended connection is shown.... company personnel, and authorized service personnel. A. Correct any leak found.
17 A. 3/8" flexible gas connector B. 3/8" dryer gas pipe
C. 3/8" to...Install a shut-off valve
1. Securely tighten all gas connections.
Do not use pipe-joint compound resistant to dryer...
Installation Instructions - Page 18
...;■ Recommended for exhausting. Replace plastic or metal foil vents with a magnetic latch. Review "Vent System Charts" and, if necessary, modify existing vent system to follow these instructions can result in death or fire. Clamps:
■■ Use clamps to seal all governing codes and ordinances. Do not use a metal foil vent. Do not use duct tape.
18...
Installation Instructions - Page 19
... the right side, left side (all models except long vent), or through the bottom.
Elbow C. Contact your local dealer to follow these instructions can be securely fastened to avoid kinking. ■■ Use as few 90° turns as possible. A. Standard rear offset exhaust installation B. Exhaust hood E. Determine vent length and elbows needed for mobile...
Installation Instructions - Page 20
...use caulking compound to seal all joints. Install Vent System
1. A gas model would be DJAV - Long Vent System Chart
Number of 90° elbows
Type of vent
Angled hoods
0
Rigid metal
160 ft... determine if your model has a long vent system, refer to dryer location using straightest path possible. Example: An electric model would be DJAV -
Run vent to the type code located on the ...
Installation Instructions - Page 21
... an additional 2/3 turn . Record hose installation or replacement dates on connector. NOTE: Do not ...to "Connect Vent." Periodically inspect and replace hoses if bulges, kinks, cuts, ...dryer must be connected to cold water faucet. Screw on coupling by hand until it is seated on the hoses for future reference.
CONNECT INLET HOSE (STEAM MODEL ONLY)
For non-steam models...
Installation Instructions - Page 22
... hand until it is secured to existing vent, make sure vent is in dryer. Turn on .
7. Move dryer to dryer fill valve
and tighten coupling
CONNECT VENT
1.
5. Check for leaks around "Y" connector, faucet, and hoses. 22 Attach other end of dryer back panel. NOTE: Do not overtighten. Check for leaks
Move dryer to final location, taking care not...
Installation Instructions - Page 23
.... ‰‰ Check to be level for certain part replacement or repair.
If dryer will reduce product performance. This odor is common when heating element is first heated. Not Level
LEVEL
2.
See "Level Dryer." ‰‰Remove film on console and any tape remaining on dryer. ‰‰Wipe dryer drum interior thoroughly with a damp cloth to...
Installation Instructions - Page 24
...instructions are registered trademarks of Acument Intellectual Properties, LLC.
24 Replace all parts and panels before servicing. Failure to the opposite side of dryer door frame with round and square-shaped doors. Remove door from dryer....
Tuck wiring into opening.
†®TORX, T20, and T25 are for models with the two screws removed earlier, as shown. Tools needed:
ALL DOORS:
2....
Specification Sheet - Page 1
...
Extra Power Button The Extra Power button boosts drying power on select Maytag® washers to get clothes ready in no time.
For complete details, see Installation Instructions packed with Door Open 90° Maximum Vent Length Venting Direction Ventless
Reference Material
Install Guide Use & Care Guide Warranty
Powder Coat
Electric
Side Swing
Yes
10
Bulky Items Delicates...
Instruction Sheet - Page 1
... is seated on . 11. Using pliers, tighten the couplings an additional two-thirds turn .
2. Remove old rubber washer from inlet hose and replace with dryer)
5' (1.5 m) Inlet Hose
Your installation may require additional parts. NOTE: Do not overtighten. C heck that the water faucets are in place.
3. Attach 2' (0.6 m) inlet hose to the coupling can result. 10...
Maytag MED5630HW Reviews
We have not received any reviews for Maytag yet.