Maytag MED5030MW Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag MED5030MW manuals!
Problems with Maytag MED5030MW?
Ask a Question
Free Maytag MED5030MW manuals!
Problems with Maytag MED5030MW?
Ask a Question
Popular Maytag MED5030MW Manual Pages
Door Reversal Instructions - Page 1
... REVERSAL INSTRUCTIONS
Tools Needed
Flat-blade screwdriver
Plastic putty knife
Minimum 8" long TORX® T25® #2 Phillips screwdriver star driver
You can change your door swing from dryer cabinet. Pull door forward off top screws
Lift door until top screws in dryer cabinet are applicable for models with putty knife or screwdriver. Set door...
Door Reversal Instructions - Page 2
... panel to dryer door so that the larger hole is on right side of dryer cabinet. Rotate outer door
Rotate outer door 180º and set it back down .
11. Remove door strike and door strike plug
Remove door strike and door strike plug from the inside of the hinge...
Door Reversal Instructions - Page 3
... on left or right within slot to adjust alignment. 12. Slide door up so screws are in bottom of a service call.
3
Tighten screws. Insert screws in hinges.
13. Troubleshooting
See your Owner's Manual or visit our website and reference Frequently Asked Questions to reinstall door. Tighten screws halfway. Position door so large end...
Dimension Guide - Page 2
... leveling legs fully extended)
G
Depth with Door Open
in your appliance's Owner's Manual, before installing and operating this appliance. Fuel Type Minimum Circuit Amperage Rating Maximum AMP Draw Operating...risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS and INSTALLATION INSTRUCTIONS, located in 421∕2 29 367∕8 287∕16 381∕2 ...
Owners Manual - Page 2
... the instructions are not followed. Flexible venting materials are very important. We have provided many important safety messages in this manual and on your appliance. All safety messages will obstruct clothes dryer airflow and increase the risk of fire. − To reduce the risk of Fire"
− Clothes dryer installation must be of a specific...
Owners Manual - Page 4
... to be guided through the steps to set up a user account and to connect your appliance.
This device may apply. Industry Canada (IC) Compliance Notice This Device complies with Part 15 of the FCC Rules. Under Industry Canada regulations, this radio transmitter may cause undesired operation.
If this transmitter must be installed such that...
Owners Manual - Page 5
... of the dryer depending on model. Cleaning should be located either in front of the lint screen. A screen blocked by a qualified appliance service or ventilation system cleaner. Doing...blue jeans or brightly colored cotton items, may be done by lint can result in the Installation Instructions. � Clean space where lint screen is completely dry.
OR 2. Thoroughly dry lint...
Owners Manual - Page 6
... power supply cord-connected dryers: 1. Replace all parts and panels before servicing. Use tape to the dryer. See "Install and remove base trim (on some models)
1. Replace the bulb with base trim, remove base trim before moving dryer. Do not use a metal foil vent. The venting system attached to follow these instructions can result in good airflow...
Owners Manual - Page 7
... inlet hose 7 To use to model) Parts package is located in the Installation Instructions. Turn on some water may vary according to reduce the risk of replacement. Special Instructions for All Installations:
Utility knife
Tin snips
Caulking gun and compound
Adjustable wrench that all models):
Flat-blade screwdriver
Wire stripper
1/4" Nut driver
Level
Leveling legs (4) (Length...
Owners Manual - Page 8
... your installation. Some codes limit, or do so can be used , top and bottom air openings are required for vented models.
Vented Models:
Vent Clamps, elbows, and vent work
Parts Needed (not supplied with dryer):
Additional parts may need : � For vented models: A location allowing for proper exhaust
installation. Add spacing on all sides of the dryer to support...
Owners Manual - Page 16
...installing the dryer.
� Make sure external exhaust hoods outside debris.
� Replace... instructions ...Guide.
� Only a 4" (102 mm) heavy metal exhaust vent and clamps may result
in reduced airflow and poor performance. � Do not install...codes and ordinances.
Flexible metal vent (acceptable only if accessible to clean): � Must be fully extended and supported...
Owners Manual - Page 17
...Guide for mobile home installations:
Exhaust vent must be converted to use. Failure to avoid kinking.
� Use as few 90° turns as possible.
� Bend vent gradually to follow these instructions... performance.
Exhaust outlet I.
Bottom exhaust installation (available only on
select 27"-wide models). Other installations are shown. Dryer B.
Contact your local...
Owners Manual - Page 18
... if your model has a long vent system, refer to the type code located on faucet.
Install exhaust hood
Connect Inlet Hoses
For vented, non-steam models, skip to... serial number plate in which the Installation Instructions do not address the vent length for the specific number of vent to seal exterior ...the inner door well. Periodically inspect and replace hoses if bulges, kinks, cuts, wear,...
Owners Manual - Page 19
... an additional two-thirds turn . Turn on .
7.
Check for leaks
Check levelness of the 5 ft (1.5 m) inlet hose ends to "Y" connector and tighten Connect Vent (Vented Models Only)
couplings
1. NOTE: Do not overtighten. Move dryer to final location
If applicable, remove protective cap from side to final location. NOTE: Do not overtighten...
Owners Manual - Page 20
... Instructions" for details.
� Set the heat cycle for the
dryer. Install and remove base trim (on .
� Check for heat.
If there is first used. 2.
For direct wire installation, turn off dryer, and check the following : � Controls are set in the dryer. Check that both circuit breakers have all parts are on some models)
To Install...
Maytag MED5030MW Reviews
We have not received any reviews for Maytag yet.