Makita XT610 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XT610 manuals!
Problems with Makita XT610?
Ask a Question
Free Makita XT610 manuals!
Problems with Makita XT610?
Ask a Question
Popular Makita XT610 Manual Pages
Instruction Manual - Page 9
... screwdriver with no load for repair.
9 Carbon brush
cap
CAUTION: • These accessories or attachments are
recommended for use with your local Makita service center for about 1 minute. Only use of any assistance for their stated purposes. After replacing brushes, insert the battery cartridge into the holes in the recessed part of injury to persons...
Instruction Manual - Page 10
... or limitation of Makita's Factory or Authorized Service Centers.
Should any trouble develop during this one...SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY. This Warranty does not apply where:
repairs have been made to state. If inspection shows the trouble is warranted to you . IN NO EVENT SHALL MAKITA...Makita will repair (or at our option, replace) without charge.
Instruction Manual - Page 5
...parts, gummy deposits, or a build-up of the lower guard spring. Be aware of the lower guard which is solidly supported...way. Leaving blade exposed is moving. Before setting the tool down . Never clamp or tie...not operating properly, they must be retracted manually only for proper closing before cutting. ... nails from other materials may be serviced before grasping cut off when the ...
Instruction Manual - Page 8
... - 45°)
and turn it clockwise for proper repairs BEFORE further usage. • NEVER tape down or defeat... serviced at a Makita service center. WARNING: • For your cutting line.
This can cause switch breakage. Electric brake For Model XSS01...is provided. Set for the desired angle (0° - 50°) by tilting
accordingly, then tighten the lever securely. Set for the ...
Instruction Manual - Page 10
...; or 45° the blade with the base using a triangular rule or square rule, etc.
1. Set the base on new cut line, and start cut line. Then turn or force the tool back to the...being blown out of 90° cut (vertical cut ) For Model XSS01 This adjustment has been made at the factory. Rip fence (Guide rule)
1. Rip fence
(Guide rule)
1 2
006710
The handy rip fence allows you to help...
Instruction Manual - Page 11
...MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is warranted to be replaced at our option, replace) without charge. This Warranty does not apply where:
repairs have been made or attempted by Makita Authorized or Factory Service Centers, always using Makita replacement parts...SAFETY and RELIABILITY, repairs, any trouble develop during this manual. OPTIONAL ACCESSORIES
CAUTION...
XAG03Z Instruction Manual - Page 3
...ensure these are not recommended to your power tool serviced by poorly maintained power tools. 22. Do not...specifically designed and recommended by
the manufacturer.
Dress properly. Power tools are caused by a qualified repair person using only identical replacement parts. in a hazardous situation. Shorting the battery terminals together may be performed. Follow instruction...
XAG03Z Instruction Manual - Page 6
... regulation. 33. Observe the instructions of the manufacturer for this
instruction manual may result in a
container ... stop operating immediately. 22. Do not use ) replace strict adherence
to assure operator safety. 31. Check that...INSTRUCTIONS. Overcharging shortens the battery service life.
3. Charge the battery cartridge before charging it is severely damaged or is properly supported...
XAG03Z Instruction Manual - Page 13
If you purchase from your Makita distributor or factory service center, be used with your Makita tool specified in this manual. Your failure to do so could result in ... Your tool is supplied with a guard for use with approved accessories which you decide to use your Makita grinder with a depressed center grinding wheel, multi-disc and wire wheel brush. OPTIONAL ACCESSORIES
CAUTION: •...
XAG03Z Instruction Manual - Page 15
... workmanship or material, Makita will repair (or at our option, replace) without charge. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. This Warranty gives you specific legal rights, and you may not apply to state. MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is caused by others: repairs are required because...
DML185 Instruction Manual - Page 4
... as nails, coins, etc.
4.
If electrolyte gets into your nearest Makita Service Center or dealer. take it in damp or wet locations. SAVE THESE INSTRUCTIONS. Shoulder strap
SPECIFICATIONS
Model
Bulb
L
Dimensions (without notice.
• Note: Specifications may create a risk of research and development, the specifications herein are subject to our continuing program of fire. 13...
DML185 Instruction Manual - Page 5
... with a little click. Wait until it locks in place with your Makita tool specified in four stages. MAINTENANCE
To maintain product safety and reliability, repairs, maintenance or adjustment should be adjusted in this time, recharge the battery cartridge. At this manual. ASSEMBLY
Replacing bulb (Fig. 3 & 4)
CAUTION: The bulb is not being inserted correctly. Always...
Makita DC18RC Instruction Manual - Page 3
...Specifications may not start. 16.
Removing and re-inserting it will come out to notify the completion of charger.
This manual contains important safety and operating instructions...ask Makita authorized
service center to replace it stops adjusting to the guide of ... comes out to notify completion of time. 6. ENGLISH
Specifications
Model Input Output Weight
DC18RA
DC18RC
A.C. 120 V 50 ...
XDT11 Instruction Manual - Page 6
... deep enough into the sleeve as far as it . Installing or removing driver bit/ socket bit
1 2
1.
This tool has a reversing switch to the neutral position. Groove 2. CAUTION: Use the reversing switch only after the tool comes to the instructions above. Driver bit 2. NOTE: If the driver bit is in the figure. Hook 3. Depress the reversing...
XDT11 Instruction Manual - Page 9
...
NOTE: Some items in this one of any trouble develop during this manual. If inspection shows the trouble is thoroughly inspected and tested before leaving the factory. MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is caused by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION: These accessories or...
Makita XT610 Reviews
We have not received any reviews for Makita yet.