Makita XT287SM1 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XT287SM1 manuals!
Problems with Makita XT287SM1?
Ask a Question
Free Makita XT287SM1 manuals!
Problems with Makita XT287SM1?
Ask a Question
Popular Makita XT287SM1 Manual Pages
XBU03 Instruction Manual - Page 2
....
2
4. This appliance is not working as described in this manual. ENGLISH WARNING - Always wear substantial footwear and long
trousers while operating the blower. 2. Keep hair, loose clothing, fingers, and all parts of research and development, the specifications herein are shown in use and before servicing.
2.
Use only as it should always be drawn into...
XBU03 Instruction Manual - Page 4
... in a container with local codes for battery cartridge
1. Do not use genuine Makita batteries. Use of these exposures varies, depending on (1) battery charger, (2) battery, and (3) product using only identical replacement parts. Electrical and battery safety 1. Service 1. Have your exposure to disposal of your eyesight.
5. SAVE THESE INSTRUCTIONS. Some examples of non...
XBU03 Instruction Manual - Page 9
...If recharging is installed improperly.
Remove the battery and ask your local authorized service center for repair.
9 ENGLISH Hole
TROUBLESHOOTING
Before asking for repairs, conduct your local authorized service center for repairs.
Battery power is not effective, replace battery. The drive system does not work correctly. Stop using Makita replacement parts for repair. If...
XBU03 Instruction Manual - Page 10
.... OPTIONAL ACCESSORIES
CAUTION: These accessories or attachments are recommended for use with your local Makita Service Center. • Adapter pipe • Extension nozzle • Flat nozzle • Shoulder... product. If annexed warranty sheet is not available, refer to the warranty details set forth at below website for the most current warranty terms applicable to the annexed...
XRU23 Instruction Manual - Page 2
...01/2014, are in the off position before installing the battery pack.
Use of residence. •...
Important safety instructions
WARNING: When using the battery adapter, read the instruction manual.
3. SAVE THESE INSTRUCTIONS.
Never allow...and attention.
4. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Type of handle No load speed
XRU23
Loop handle
2: 0 - 6,...
XRU23 Instruction Manual - Page 4
...instructions for operation. Before use a cutting tool which may ignite the dust or fumes.
19. Do not use always check that the tool is not recommended by a qualified repair...manual...only identical replacement parts. Always ...service center ...parts, mounting, and any adjusting key or wrench before checking, cleaning or working range of the tool.
8. as guards supplied with local codes...
XRU23 Instruction Manual - Page 5
... recommended replacement parts and accessories.
7. Keep all instructions and cautionary... this instruction manual may... service center.
8. 21. Follow instructions...repaired only by third parties, forwarding agents, special requirement on steep slopes.
22.
volts
direct current
no load speed
revolutions or reciprocation per minute
Important safety instructions for loose fasteners and damaged parts...
XRU23 Instruction Manual - Page 6
... the Makita tool and charger. SAVE THESE INSTRUCTIONS.
Overcharging shortens the battery service life.
3. Tape or mask off open ...the battery cartridge if you notice less tool power.
2. Installing the batteries to cause burns. 16. Pay attention to disposal... of it in the packaging. 11.
Unless the tool supports the use near high-voltage electrical power lines. Let a...
XRU23 Instruction Manual - Page 12
Set the angle and position of the cutting tool(s) supplied as shown in the figure, and then tighten the bolt.
1
Installing the protector
WARNING: Never use the tool without the guard illustrated in some countries. Failure to do so can replace the cutting tool easily.
Rotate the spindle until the hex wrench is not...
XRU23 Instruction Manual - Page 14
...diameter specified in serious personal injury. To maintain product SAFETY and RELIABILITY, repairs, any more. Cleaning the tool
Clean the tool by wiping off ...instruction manual. NOTE: If the nylon cord does not feed out while tapping the head, rewind/replace the nylon cord by Makita Authorized or Factory Service Centers, always using Makita replacement parts. To avoid overheating of replacing...
XRU23 Instruction Manual - Page 17
... to allow it is installed improperly. If recharging is loosely attached. Recharge the battery.
They may be included in this manual. Battery is rotating to cause the cord to the warranty details set forth at below website for repairs.
Ask your respective country.
Stop using Makita replacement parts for your local authorized service center for the most...
XBU03 Parts Breakdown - Page 3
... Tech Bulletin
1 XBU03
Unit Complete
Products with multiple versions are listed in subsiding order with the newest version on top not indented. Part No.
No.
Description
11
183M73-7
HOUSING SET
1
12
651395-0
SWITCH C3JW-6B-PA6N
1
13
459696-8
SWITCH LEVER
1
14
459697-6
CONTROL LEVER
1
15
213154-6
O RING 14
1
16
459698-4
LINK
1
17...
New Tool Flyers English - Page 1
... and over-heating • 3-year limited warranty on tool, battery and charger
SPECIFICATIONS
Max. All models and accessories subject to 6,000 RPM • String trimmer features high/low button...Cutting Swath 13" No Load Speed (var. 2 spd 0 - 4,500 / 0 - 6,000 RPM UPC Code 088381-728737
STANDARD EQUIPMENT
• 18V LXT® Brushless 13" String Trimmer (XRU23Z) • 18V LXT&#...
XRU23Z Parts Breakdown - Page 3
...Bulletin
Part No. NUT M6
1
1 010 210235-7
BALL BEARING 625ZZ
1
1 011 227830-6
HELICAL GEAR 32
1
1 012 327678-7
CUTTER SHAFT
1
1 013 210216-1
BALL BEARING 6001DDW
1
1 014 183R54-1
MOTOR HOUSING SET
... order with the newest version on top not indented.
Description
1 001 183R54-1
MOTOR HOUSING SET
1
1 002 652069-6
FLAT HEAD SCREW M3X6
3
1 003 629A22-3
STATOR
1
1 ...
XRU23Z Parts Breakdown - Page 4
Description
1 040 412863-6
LOCK OFF LEVER
1
1 041 459758-2
SWITCH LEVER
1
1 042 233622-3
TORSION SPRING 12
1
1 043 266326-2
TAPPING SCREW 4X18
8
1 044 183R55-9
GRIP HOUSING SET
1
1 046 620D78-7
CONTROLLER
1
1 048 644809-6
TERMINAL
1
Notes
INC. 36
rev 0_11/13/20
4 XRU23 Tech Bulletin
1 XRU23
Unit Complete
Products with multiple versions are listed ...
Makita XT287SM1 Reviews
We have not received any reviews for Makita yet.