Makita XT255T Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XT255T manuals!
Problems with Makita XT255T?
Ask a Question
Free Makita XT255T manuals!
Problems with Makita XT255T?
Ask a Question
Popular Makita XT255T Manual Pages
Instruction Manual - Page 3
.... Keep cutting tools sharp and clean.
Service 28. GEB123-1
CORDLESS CUTOUT TOOL SAFETY WARNINGS
1. Do not cut metal objects such as the floor, workbench, etc. 7. Use of fire when used . If liquid contacts eyes, additionally seek medical help. Follow instruction for misalignment or binding of moving parts, breakage of dust extraction and collection...
Instruction Manual - Page 4
... down before removing the bit from moving parts. 15. Charge the battery cartridge once ...attention to the need to use ) replace strict adherence to the tool and ...battery cartridge when you do not use this instruction manual may reach or exceed 50 ﾟ ...battery cartridge to support or guide the workpiece. 14. SAVE THESE INSTRUCTIONS. Overcharging shortens the battery service life.
3....
Instruction Manual - Page 9
... are required because of Makita's Factory or Authorized Service Centers. This Warranty gives you specific legal rights, and you . Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. THIS DISCLAIMER APPLIES BOTH...
Instruction Manual - Page 2
ENGLISH (Original instructions)
SPECIFICATIONS
Model
XSF03
Capacities
Self drilling screw Drywall screw
6 mm (1/4") 5 mm (3/16")
No load speed (...connecting to change without notice.
• Specifications and battery cartridge may differ from heat, oil, sharp edges or moving parts. Keep proper footing and balance at all warnings and instructions for outdoor use a ground fault circuit...
Instruction Manual - Page 3
...is not in this instruction manual may contact hidden wiring....serviced by the manufacturer. Use of fire when used . avoid contact. SAVE THESE INSTRUCTIONS.
Use of injury and fire.
26. This will do not allow persons unfamiliar with these instructions to be sure you have the power tool repaired... below when using only identical replacement parts. If liquid contacts eyes, ...
Instruction Manual - Page 4
...current
･ no load speed
･ revolutions or reciprocation per minute
IMPORTANT SAFETY INSTRUCTIONS
ENC007-8
FOR BATTERY CARTRIDGE
1. USD301-5
Symbols
The followings show the symbols used ...power.
2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
3. Charge the battery cartridge once in locations where the temperature may ...
Instruction Manual - Page 6
... switch trigger. The tool will automatically stop during operation if the tool or battery are placed under one minute after switch trigger release, have tool serviced at a Makita service center. Be careful not to extend tool and battery life. The lamp turns on the lamp again, slightly pull the switch trigger again. This...
Instruction Manual - Page 7
...CAUTION: When not operating the tool, always set the reversing switch lever to change in "A" direction for less depth and in depth.
3 mm (1/8")
1. Installing or removing the bit
1. more depth. Drive...neutral position. Overheat protection for the screw, continue adjusting until you obtain the proper depth setting. One full turn of the locator equals 2 mm (1/16") change the direction of ...
Instruction Manual - Page 8
...1. Then install the locator by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Groove 2....Makita tool specified in this manual. Then grasp the bit with your local Makita Service Center. • Phillips Insert bits • Magnetic bit holder • Makita... SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance ...
Instruction Manual - Page 9
... made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY. If inspection shows the trouble is thoroughly inspected and tested before leaving the...
XSF03Z Parts Breakdown - Page 2
...1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 1 SET 2 PC. 0 1 7 PC. 3 PC. 1 1 1 PC. 1 PC. 1 SET 2 PC. 0 1 1 PC. 1 PC. 2 PC. 1 3 PC. Model XSF03Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part# Description
Q'ty Unit
001
455591-0 LOCK RING
002
424235-3 SEAL RING 30
... COMPLETE
029
233619-2 TORSION SPRING 3
030
187968-8 HOUSING SET
030 C10 263005-3 RUBBER PIN 6
030 D10
INC. ...
Makita XOC01Z Parts Breakdown - Page 2
Model XOC01Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part# Description
Q'ty Unit
001
346796-2 SHOE PLATE
002
266898-7 THUMB SCREW M4X8
003
763675-3 COLLET NUT
004
763677-9 COLLET CONE 3.18
005
142656-4 SPINDLE COMPLETE
006
455181-9 SHAFT LOCK
007
234332-5 COMPRESSION SPRING 7
008
266374-1 TAPPING SCREW 4X25
009
346795-4 SHOE SUPPORT...GUIDE BIT 3.18 SET...
Makita DC18RC Instruction Manual - Page 3
... of charging. 4. When the battery cartridge is damaged, ask Makita authorized
service center to replace it to the guide of electric shock or fire. 13. Inserting the battery cartridge into the proper AC voltage source. IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
1. This manual contains important safety and operating instructions for use a step-up and charging will light up transformer...
Makita DC18RC Instruction Manual - Page 4
...wear out. The battery employed in a location exposed to repair or maintenance, if the yellow warning light will begin after the cooling fan installed in green and red color, charging is unplugged. BH9020A...damaged. The terminals on cooling fan - Trouble on the charger or battery cartridge are clogged with cooling fan for charging Makita-battery cartridge. Incomplete cool down of ...
XT255TNew Tool Flyer English - Page 1
...XT255T
PRODUCT HIGHLIGHTS
DRYWALL SCREWDRIVER
Push Drive™ Technology - Circular Guide (193454-9) 4. Dust Extracting Cut-Out Base (193449-2)
1
2
3
4
5
All specifications subject to the changing demands of drywall and framing applications
• Push Drive™ Technology - All models...on hand.
The Makita Teal Color is the trade dress of Makita Corporation and is ...
Makita XT255T Reviews
We have not received any reviews for Makita yet.