Makita XRU16PT Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XRU16PT manuals!
Problems with Makita XRU16PT?
Ask a Question
Free Makita XRU16PT manuals!
Problems with Makita XRU16PT?
Ask a Question
Popular Makita XRU16PT Manual Pages
XRU16/17 Instruction Manual - Page 2
... the attachment(s), including the battery cartridge. It is responsible for accidents or hazards occurring to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
ENGLISH (Original instructions)
SPECIFICATIONS
Model: Handle type No load speed (at each rotation speed level)
Overall length (without cutting tool) Nylon cord diameter
XRU16...
XRU16/17 Instruction Manual - Page 4
...
11. Except in the instructions. Charging improperly or at ...codes for easy and proper action. Always ensure a safe footing.
11. 7. Have servicing...repaired or replaced by use the tool in wet locations.
16. Take care against injury to fire or excessive temperature. Should the cutting tool hit stones or other part that could cause a hazard if damaged by our authorized service...
XRU16/17 Instruction Manual - Page 6
... the products specified by our authorized service center.
8. Before using battery.
...often you do this type of this instruction manual may result in good working condition. by...may result in a safe place. Installing the batteries to disposal of it ... /after use ) replace strict adherence to the Dangerous Goods Legislation requirements. Have the tool repaired only by Makita....
XRU16/17 Instruction Manual - Page 9
...and serious personal injury. When the switch trigger is being accidentally pulled, a lock-off lever. CAUTION: Before installing the battery cartridge into the tool, always check to the "OFF" position when released.
To start unintentionally and ...tool speed increases by increasing pressure on the battery cartridge to our authorized service center for proper repairs BEFORE further usage.
XRU16/17 Instruction Manual - Page 11
...electric brake. Failure to switch off and battery cartridge is released, have the tool serviced at our service center. Hex socket head bolt 2. Handle 3.
WARNING: Never start because of ... provides a comfortable working position and then secure with the one in the correct direction.
2. Installing the handle
For XRU16 1. Handle
holder
For XRU17 1. Put the handle on the damper. ...
XRU16/17 Instruction Manual - Page 12
...storage
CAUTION: Be careful not to the tool. Hex wrench
Installing the protector
WARNING: Never use , store the hex wrench as a safety part to the handle using the screw on the barrier.
Barrier ...do not remove it. Attaching the barrier
For the loop handle model only (country specific) If the barrier is included in your model, attach it to prevent you from the cutting tool,
flying ...
XRU16/17 Instruction Manual - Page 13
...blade immediately. Protector
For nylon cutting head
CAUTION: Take care not to injure yourself on the cutter for specifications.
1
2
3
4
3
4
6
► 1 .
Rotate the spindle until the hex wrench is... Hex wrench
1. Make sure that , install the protector extension.
NOTE: Turn the tool upside down so that you can replace the cutting tool easily. NOTE: The type of...
XRU16/17 Instruction Manual - Page 14
... box wrench.
1
4
3
5
2
3
► 1 . Remove the hex wrench from the gear case.
To remove the nylon cutting head, follow the installation procedures in reverse.
2
► 1 . To remove the cutter blade, follow the installation procedures in reverse. Put on the tool. Put the clamp washer and cup onto the cutter blade and then tighten...
XRU16/17 Instruction Manual - Page 16
... tighten the hex socket head bolt.
1
► 1 . If the cutting tool is damaged, replace it to release the tool from the shoulder harness.
2.
Adjust the hanger position as illustrated to a... ENGLISH WARNING: Be extremely careful to observe the distance between the hanger and the unguarded part of the cutting tool
Correct handling of the tool could result in serious personal injury....
XRU16/17 Instruction Manual - Page 17
...replacement parts...Authorized or Factory Service Centers, always...repairs, any more. Most effective cutting area NOTICE: The bump feed will not operate properly if the nylon cutting head is secured to perform inspection or maintenance on the type of replacing the nylon cord varies depending on the tool. Cleaning the tool
Clean the tool by following the procedures in this instruction manual...
XRU16/17 Instruction Manual - Page 20
... battery cartridge. If annexed warranty sheet is not effective, replace battery cartridge. TROUBLESHOOTING
Before asking for repair. If you need any assistance for use the recommended accessories or attachments indicated in the manual, do not attempt to the warranty details set forth at below website for repair. Motor stops running after a little use accessory or attachment...
XRU16Z Parts Breakdown - Page 3
... CLAMP
1
1 32 347116-3
HANGER
1
1 33 922212-4
HEX. Section Fig. XRU16 Tech Bulletin
Part No. SOCKET HEAD BOLT M5X12
1
rev 1_07-31-20
3
Notes INC. 2-16 INC. 3-5,7
INC...257986-1
RETAINING RING (EXT) S-9
1
1 16 257987-9
RETAINING RING (INT)R-24
1
1 17 191B54-1
PROTECTOR U 430 SET MG
1
1 18 922216-6
HEX. SOCKET HEAD BOLT M5X25
4
1 28 318272-6
HANDLE HOLDER 1
1
1 29 319705-4...
XRU16Z Parts Breakdown - Page 4
... 632G61-0
SWITCH UNIT
1
1 40 233540-5
TORSION SPRING 11
1
1 41 459146-3
LOCK OFF LEVER
1
1 42 233101-1
COMPRESSION SPRING 4
1
1 43 183L61-8
GRIP SET
1
1 44 651436-2
SWITCH C3JW-1A-P-2
1
1 45 687260-7
STRAIN RELIEF
1
1 46 266326-2
TAPPING SCREW 4X18
1
1 47 911258-5
PAN HEAD SCREW M5X35
1
...newest version on top not indented. No. XRU16 Tech Bulletin
Part No. Section Fig.
XRU16Z Parts Breakdown - Page 5
... multiple versions are listed in subsiding order with the newest version on top not indented. XRU16 Tech Bulletin
Part No. WRENCH 4
1
1 A08 831304-7
ACCESSORY BAG
1
1 A09 195246-2
SAFETY GOGGLE
1
1 A10B 197283-2
BATTERY BL1850B SET
2
Notes INC. 63,66,68
INC. 50 INC. 54
NOT PICTURED NOT PICTURED NOT PICTURED NOT PICTURED NOT...
XRU16PT New Tool Flyers English - Page 1
... shifts
from 4,600-7,000 RPM for extended run time or added power
SPECIFICATIONS
Blade Diameter 9" No Load Speed (var. 3 spd.)....0 - 4,600 /... 1.25 LH Overall Length 72-1/2" Net Weight (with the U.S. UPC Code (XRU16PT 088381-889926 UPC Code (XRU16Z 088381-889933
STANDARD EQUIPMENT
XRU16PT
• (2) 18V LXT® ...models and accessories subject to change without battery 14 lbs.
Makita XRU16PT Reviews
We have not received any reviews for Makita yet.