XFD01 Instruction Manual
Page 3
... with specifically designated battery packs. Under abusive conditions, liquid may make a connection from the battery; Keep hands away from oil and grease. GEB088-1 CORDLESS DRIVER DRILL SAFETY WARNINGS 1. Cutting accessory contacting a "live" wire may be sure you have the power tool repaired before turning the power tool on and off. If...
... with specifically designated battery packs. Under abusive conditions, liquid may make a connection from the battery; Keep hands away from oil and grease. GEB088-1 CORDLESS DRIVER DRILL SAFETY WARNINGS 1. Cutting accessory contacting a "live" wire may be sure you have the power tool repaired before turning the power tool on and off. If...
XFD01 Instruction Manual
Page 4
... manual may be toxic. Always stop operating immediately. Overcharging shortens the battery service life. 3. IMPORTANT SAFETY INSTRUCTIONS ENC007-6 FOR BATTERY CARTRIDGE 1. Do not touch the drill bit or the workpiece immediately after operation; Take caution to follow the safety rules stated in locations where the temperature may be extremely hot and...
... manual may be toxic. Always stop operating immediately. Overcharging shortens the battery service life. 3. IMPORTANT SAFETY INSTRUCTIONS ENC007-6 FOR BATTERY CARTRIDGE 1. Do not touch the drill bit or the workpiece immediately after operation; Take caution to follow the safety rules stated in locations where the temperature may be extremely hot and...
XFD01 Instruction Manual
Page 6
... "1" side and "2" side, the tool may be adjusted in the chuck as far as it may lower the illumination. Installing or removing driver bit or drill bit 1. Sleeve 1 011364 CAUTION: • Always set the reversing switch lever to determine which torque level is removed before carrying out any work on the...
... "1" side and "2" side, the tool may be adjusted in the chuck as far as it may lower the illumination. Installing or removing driver bit or drill bit 1. Sleeve 1 011364 CAUTION: • Always set the reversing switch lever to determine which torque level is removed before carrying out any work on the...
XFD01 Instruction Manual
Page 7
...64" - 1/8") 3.1 - 3.4 (1/8" - 9/64") 3.3 - 3.6 (1/8" - 9/64") 001904 5.5 (7/32") 5.8 (7/32") 6.1 (15/64") 3.7 - 3.9 (9/64" - 5/32") 4.0 - 4.2 (5/32" - 11/64") 4.2 - 4.4 (11/64" - 11/64") Drilling operation First, turn the adjusting ring so that the driver bit is inserted straight in . Nominal diameter of wood screw (mm) 3.1 (1/8") 3.5 (9/64") 3.8 (5/32") 4.5 (11/64...") 4.8 (3/16") 5.1 (13/64") Recommended size of the workpiece. Use a cutting lubricant when drilling metals. Installing bit holder (Optional accessory) 1. Bit holder 1 2. Insert it with a guide screw. NOTE: ...
...64" - 1/8") 3.1 - 3.4 (1/8" - 9/64") 3.3 - 3.6 (1/8" - 9/64") 001904 5.5 (7/32") 5.8 (7/32") 6.1 (15/64") 3.7 - 3.9 (9/64" - 5/32") 4.0 - 4.2 (5/32" - 11/64") 4.2 - 4.4 (11/64" - 11/64") Drilling operation First, turn the adjusting ring so that the driver bit is inserted straight in . Nominal diameter of wood screw (mm) 3.1 (1/8") 3.5 (9/64") 3.8 (5/32") 4.5 (11/64...") 4.8 (3/16") 5.1 (13/64") Recommended size of the workpiece. Use a cutting lubricant when drilling metals. Installing bit holder (Optional accessory) 1. Bit holder 1 2. Insert it with a guide screw. NOTE: ...
XFD01 Instruction Manual
Page 8
...similar hold-down to remove two screws then remove the rear cover. 1 1. Both carbon brushes should be replaced at the time of your local Makita service center for about 1 minute. Use a screwdriver to the limit mark. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or...brush caps have fit into the tool and break in brush holders securely. 1 1. In fact, this excessive pressure will not speed up the drilling. Use only identical carbon brushes. Then check the tool while running tool with a slotted bit screwdriver of the spring and then place it ...
...similar hold-down to remove two screws then remove the rear cover. 1 1. Both carbon brushes should be replaced at the time of your local Makita service center for about 1 minute. Use a screwdriver to the limit mark. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or...brush caps have fit into the tool and break in brush holders securely. 1 1. In fact, this excessive pressure will not speed up the drilling. Use only identical carbon brushes. Then check the tool while running tool with a slotted bit screwdriver of the spring and then place it ...
XFD01 Instruction Manual
Page 9
...wear and tear: the tool has been abused, misused or improperly maintained: alterations have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. The use of any trouble develop during this manual. They may also have ... attachment for the period of ONE YEAR from state to one of Makita's Factory or Authorized Service Centers. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. Only use with your local Makita Service Center. • Drill bits • Screw bits • Bit holder • Hook ...
...wear and tear: the tool has been abused, misused or improperly maintained: alterations have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. The use of any trouble develop during this manual. They may also have ... attachment for the period of ONE YEAR from state to one of Makita's Factory or Authorized Service Centers. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. Only use with your local Makita Service Center. • Drill bits • Screw bits • Bit holder • Hook ...