Makita AN923 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita AN923 manuals!
Problems with Makita AN923?
Ask a Question
Free Makita AN923 manuals!
Problems with Makita AN923?
Ask a Question
Popular Makita AN923 Manual Pages
Owners Manual - Page 2
...by keeping noise levels within prescribed limits. In certain cases, shutters should be used.
7. Never attempt to... when under the influence of the tool, read this instruction manual carefully before using the tool.
2. they will ignite and...SPECIFICATIONS
Model
AN923
AN943
Air pressure
4.5 - 8.5 kgf/cm2G (65 - 120 PSIG)
Nail length
50 mm (2") - 90 mm (3-1/2")
Nail capacity
64 - 74 pcs.
60...
Owners Manual - Page 3
... propane, acetylene, etc.) is set to carve or engrave on the tool label for this manual. caused by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Nails may occur.
34. Always disconnect the air hose and remove all safety systems are performed. Always check contact element as required.
15. SAVE THESE INSTRUCTIONS
WARNING: MISUSE or failure to...
Owners Manual - Page 4
... install an air set is not used, oil the tool with an internal diameter of over 3 ft3/minute is required. When an air set (oiler, regulator, air filter) as close as possible to assure continuous, efficient nailing ...be done before and after pneumatic tool oil is 0.5 seconds. Thus, for every 30 nails. Air supply hoses shall have a minimum working pressure rating of 10.7 kgf/cm2G (150 ...
Owners Manual - Page 5
... set to disengage it from the strip of nails from the tool.
• Never hook the tool at high location or on the tool.
007006
1. Generally speaking, the tool service life will become shallower as the adjuster is turned fully in the A direction shown in the B direction, decrease the air pressure. Pusher lever 2. Loading nailer...
Owners Manual - Page 6
..., set to the "Intermittent Nailing" mode, WITH THE TRIGGER HELD IN A HALF-PULLED POSITION, an unexpected nailing could occur, if contact element is allowed to drive a nail carefully and very accurately. Slip the air socket of recoil. Be sure that the change the nailing
method, always make sure that the air socket locks firmly into position when installed...
Owners Manual - Page 7
...nailer Always check the tool for an extended period of time, lubricate the tool using pneumatic tool oil and store the tool in the driver guide. Change lever
Handle nail coils and their connector breaks, causing poor nail... Always disconnect the air hose from the magazine before operation. Trigger lock 2. Avoid exposure to retract the driver. Pliers 2. If the nail coils have been ...
Owners Manual - Page 8
... by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Air filter 1
To maintain product SAFETY and RELIABILITY, repairs, any assistance for its stated purpose. Drain cock 1
004318
1. ACCESSORIES
CAUTION: • These accessories or attachments are recom- If you need any other accessories or attachments might present a risk of the air set and air hose...
Parts Breakdown - Page 1
Parts Breakdown
AN923
Page 1 of 3
8/18/2010
Parts Breakdown - Page 2
... 344765-7 266370-9
Part Name CYKINDER SEPARATOR, AN923 O RING 87, AN8300 O RING 60, AN922 CYLINDER, AN923 O RING 61, HM1800 CUSHION F, AN922 CUSHION GUIDE, AN922 COMPRESSION SPRING 50, AN922 O RING, 9820-2 O RING 56, AN922 HEAD VALVE, AN923 VALVE SEAT, AN923 WASHER 34, AN922 CUSHION REAR, AN923 O RING 49, AN922 DRIVER CPL., AN923 H.S.H.BOLT M5X10, AN923 EXHAUST COVER, AN923 H.S.H. BOLT M6X25...
Parts Breakdown - Page 3
...256770-1 419119-8 262054-7 345673-5 231309-1 345624-8 233038-2 256489-2 951054-9 233908-5 810097-9 819199-8 266370-9 122742-7 192517-8 195246-2
181434-7
Parts Breakdown
O RING 60, HR3851 DRIVER GUIDE, AN923 H.S.H.BOLT M8X25, AN923 COMP. COMP. SPRING 4-11, AN923 INDICATION LABEL, AN923 INDICATION LABEL, AN923 H.S.H.BOLT M6X12, AN923 HOOK ASS'Y, AN943 SAFETY GOGGLE, AN611 N/A
OIL SUPPLY 30CC, AF502...
Flyer (English) - Page 1
... user
control over firing options
EFFICIENCY
Models AN923 AN943
Simply drop nails into the magazine and engage pusher lever for a quick
2-step loading process
DURABILITY
Filter
Built-in air filter minimizes dust and debris, prolonging life
and minimizing maintenance
ACCURACY
"Tool-less"depth adjustment with 9 settings allows user to drive nails to the
precise level onthe...
Flyer (English) - Page 2
... control and comfortable handling
STANDARD EQUIPMENT
■ Oil Supply (181434-7) ■ Safety Goggles (192517-8) ■ Tool Hook (122742-7)
SPECIFICATIONS
Model AN923
Operating Air Pressure Nail Size
Magazine Capacity Dimensions (L x W x H) Net Weight Shipping Weight UPC Code
AN923 65 - 120 PSI 2" to 3-1/2" .113 - .162 Shank diameter (plastic or wire collated) 64 - 74 22" x 4-1/4" x 13-11...
Makita AN923 Reviews
We have not received any reviews for Makita yet.