Makita XCV19Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XCV19Z manuals!
Problems with Makita XCV19Z?
Ask a Question
Free Makita XCV19Z manuals!
Problems with Makita XCV19Z?
Ask a Question
Popular Makita XCV19Z Manual Pages
XCV19 Instruction Manual - Page 2
...use and before servicing.
2. Do not use the battery cartridges and chargers listed above may not be available depending on wet surfaces.
3. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Maximum air volume...following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. Use only as a toy.
If appliance is necessary when used as described in this manual.
Use only ...
XCV19 Instruction Manual - Page 4
... specifically designated battery packs. Follow all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using only identical replacement parts....a breakdown.
6. Important safety instructions for tool. Symbols
The followings show the symbols used for battery cartridge
1. Have servicing performed by a qualified repair person using battery.
2.
It...
XCV19 Instruction Manual - Page 5
...Installing the batteries to cause burns.
16. Keep the battery away from the tool and dispose of the tool or battery cartridge.
18.
Charge the battery cartridge if you notice less tool power.
2. Such conduct may result in a fire.
8. SAVE THESE INSTRUCTIONS. Overcharging shortens the battery service... and damage. Unless the tool supports the use near a high-voltage...
XCV19 Instruction Manual - Page 9
... the latch, then take out the filter bag. Strip NOTICE: Do not use . Overdischarge protection
When the battery capacity becomes low, the tool stops automatically. Replace the filter bag when it to become overloaded. Pull the strip on the cardboard can be sure that the appliance is switched off and stop...
XCV19 Instruction Manual - Page 10
...ambient temperature, the indication may occur and
cause fire.
Brushroll error
Blinking On
The brushroll is stopped by abnormal reason. The brushroll is under high load for...capacity
50% to 100%
20% to turn on / off the appliance when this indicator lights up, replace the filter bag. (Refer the section of dust 3. The indicator lamps light up during operation. Otherwise the...
XCV19 Instruction Manual - Page 11
... a personal injury. If you let go of motion is equipped with click. ON / mode change the operating mode in the same mode as the previous setting.
When the adjusting lever points the B mark, the brushroll is located at the lowest point above the floor and is running. Switch action
Foot lever...
XCV19 Instruction Manual - Page 13
... hose, insert the hose into the aluminum pipe until it .
13 ENGLISH Aluminum pipe
To install the attachment, twist and insert it securely to the Makita service center for replacement
Using the hose
The hose is suitable for cleaning tight quarters, or high places.
► 1 . Using the side brush
The side brush is...
XCV19 Instruction Manual - Page 14
...install the filter, insert the side without a filter or continue to the operator.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service...prevent the filter from the filter. Tools made of the cleaner using Makita replacement parts. Hook
2. HEPA filter 3. NOTICE: To keep optimum suction power and ...
XCV19 Instruction Manual - Page 15
... results in poor dust collecting.
1
2 ► 1 . Align the tongue of the brushroll gets short, ask the Makita service center for the inside of the aluminum pipe and the hose, and the suction hose. Install the hose, aluminum pipe, brushroll, and bottom plate. If the appliance is operated without the brushroll results in...
XCV19 Instruction Manual - Page 16
... light The caster wheel is lighting. Clean or replace the HEPA filter.
The appliance is installed improperly.
Clean or replace the HEPA filter.
If you find a problem that there is no entanglement
rotating speed is declined. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs, conduct your own inspection first. Not working...
XCV19 Instruction Manual - Page 17
... this product.
MAKITA LIMITED WARRANTY
Please refer to the annexed warranty sheet for your local Makita Service Center. • Corner nozzle • Round brush • HEPA filter • Filter ... is not available, refer to the warranty details set forth at below website for the most current warranty terms applicable to this manual. If you need any other accessories or attachments ...
XCV19 Parts Breakdown - Page 3
Model XCV19Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
1
266326-2
...LEVER A COMPRESSION SPRING 5 STAY COMPRESSION SPRING 8 DUST BOX COMPLETE CAUTION LABEL VALVE COMPLETE FILTER BAG SET LATCH MAIN FILTER H SET SEAL RING A DUST BOX COVER TAPPING SCREW 4X18 MOTOR COVER COMPLETE SUPPORT RING FAN COVER HEX. NUT M6 WASHER 6
4 PC. 1 PC. 0 1 1 1 ...
XCV19 Parts Breakdown - Page 4
...-4
96
266326-2
97
122A42-1
106
265199-0
108
422574-5
FAN 94 FLANGE TAPPING SCREW 4X18 FAN BASE ROTOR STATOR SUPPORT CONTROLLER B PAN HEAD TAPPING SCREW 2X10 BAND DAMPER C SUPPORT A MOTOR HOUSING SET INC. 58 MOTOR HOUSING SET INC. 57 TAPPING SCREW 4X18 CONTROLLER HEIGHT CHANGE LEVER LOCK LEVER B COMPRESSION SPRING 7 BATTERY COVER CAM TAPPING SCREW...
XCV19 Parts Breakdown - Page 5
... BRUSH TAPPING SCREW 4X18 HINGE HOLDER SWITCH UNIT TAPPING SCREW 4X18 HINGE HOLDER FOOT LEVER COMPRESSION SPRING 6 PIN 4 LOWER HOUSING COMPLETE CAUTION LABEL BRUSH COMPLETE SET CASTER 75 COMPLETE LONG SASH NOZZLE SET ROUND BRUSH SET
1 1 1 0 1 2 PC. 1 1 2 PC. 1 1 1 PC. 1 1 1 1 PC. 2 1 PC. 1 PC...
XCV19Z New Tool Flyers English - Page 1
...XCV19Z) UPC Code 088381-735681 (XCV19PG) UPC Code 088381-725743 ...Filter Dust Bag,10/pk, XCV19 (191D63-2) 4. All models and accessories subject to stock on any floor type
SPECIFICATIONS
Air Flow Rate 67 CFM Static Water Lift 48" ...(191D65-8)
1
2
3
All specifications subject to 60 minutes of continuous run time on medium setting and 30 minutes on high setting using two 18V LXT® 6....
Makita XCV19Z Reviews
We have not received any reviews for Makita yet.