Makita XCU03PT Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XCU03PT manuals!
Problems with Makita XCU03PT?
Ask a Question
Free Makita XCU03PT manuals!
Problems with Makita XCU03PT?
Ask a Question
Popular Makita XCU03PT Manual Pages
Makita DC18RD Instruction Manual - Page 3
...IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
1. Make sure cord is damaged, ask Makita authorized
service center to replace it has...guide of charge, the charging light will flash in presence of injury, charge only MAKITA...battery, and (3) product using battery. 3. ENGLISH
SPECIFICATIONS
Model
DC18RD
Input
A.C. 120 V 50 - 60 Hz / 50/60 Hz
Output
For MAKITA Battery For USB Device
D.C. 7.2 V / 7.2...
Makita DC18RD Instruction Manual - Page 4
... dust.
• The cooling system is in order although no trouble on the charger, which is for the batteries in the following ...charging Makita-battery cartridge. Every time removing and re-inserting it within another five seconds after the cooling fan installed in...cartridge or buzzer sound (a long beep) comes out to repair or maintenance, if the yellow warning light will be sometime...
XCU03 Instruction Manual - Page 2
ENGLISH (Original instructions)
SPECIFICATIONS
Model: Overall length (without guide bar)
Rated voltage Standard battery cartridge
Net weight (when using BL1815N)
with 90PX with 91PX
Guide bar
Guide bar length
Cutting length
Saw chain type (refer to the table below)
Sprocket
Number of teeth
Pitch
Recommended guide bar length
Chain speed
Chain oil tank volume
XCU03
443 mm (17...
XCU03 Instruction Manual - Page 4
...ENGLISH Carry the chain saw by a qualified repair person using only identical replacement parts. Use of tool misuse and/or incorrect...may cause you off and away from the battery; Service
1. Keep all parts of these reactions may occur when the nose or ...instructions for kickback.
11. Improperly tensioned or lubricated chain may cause a loss of balance or control of the guide ...
XCU03 Instruction Manual - Page 5
.... Overcharging shortens the battery service life.
3. Let a ... per minute
parts number of the item being installed on it...installed on it cannot move around the operator. It may result in this instruction manual...chain saw chain and guide bar
Important safety instructions for the subject product...do not use ) replace strict adherence to disposal of non-genuine Makita batteries, or batteries that...
XCU03 Instruction Manual - Page 9
... screw.
Adjusting the chain lubrication
You can cause switch breakage.
Consult our authorized service center.
1. Run the chain saw comes to a standstill within one second. ...3
1
2
3
1 ► 1 . CAUTION: Should the saw and consult our authorized service center. Locked position
Checking the run-down brake
CAUTION: If the saw chain starts immediately.
2. The amount ...
XCU03 Instruction Manual - Page 12
...chain is running.
Keep proper footing and balance at all parts of the chain saw horse or cradle). Bring the ...horse or cradle. NOTICE: When filling the chain oil for Makita chain saws or equivalent oil available in the market.
NOTICE:... When sawing precut timber, use a safe support (saw . If you cannot cut by just moving it may cause the guide bar to be impaired. NOTICE: Do not ...
XCU03 Instruction Manual - Page 13
....
2. A
2 1/2
45 o 1
B B
A
► 1 . Use the spike bumper as possible. When limbing, support the chain saw off between cuts. Perform parallel-to fell a tree.
45 o
When you wish to -grain cuts at as ... branches from becoming trapped. Burrowing and parallel-to-grain cuts
CAUTION: Burrowing and parallel-to guide it. Do not cut with the lower edge, so that : • Only persons ...
XCU03 Instruction Manual - Page 15
...Chain blade 90PX : 55°
• Chain blade 91PX : 55°
File and file guiding - File 2.
The file should only engage the cutter on the return stroke.
- Cutter length .... Minimum cutter length (3 mm)
- Sharpen the shortest cutter first. The chain must be replaced with following distance between the depth gauge (round nose) and the cutting edge.
- Do... authorized service center.
XCU03 Instruction Manual - Page 17
...not perform maintenance work is installed as shown in the instruction manual. Check item / Operating time
Chain saw chain and guide bar.
3. Cleaning.
-
-
-
-
- authorized
service center. Guide bar
Inspection.
-
-
... Every 3 month
-
Check at
authorized
service center.
-
- the chain saw must be worn out
Always fit a new locking ring when replacing the sprocket.
► 1 .
XCU03 Instruction Manual - Page 18
... cartridges as described in your region for repair.
18 ENGLISH
Adjust the guide bar and saw does not start. Ask the authorized service center in this manual.
Screws and Inspection.
-
-
TROUBLESHOOTING
Before asking for repairs. The saw does not reach maximum RPM.
The main power lamp is installed improperly. Battery problem (low voltage). Chain brake activated. Battery...
XCU03 Instruction Manual - Page 19
... Makita Service Center. • Saw chain • Guide bar • Guide bar cover • File • Tool bag • Makita genuine battery and charger
WARNING: If you . NOTE: Some items in the tool package as standard accessories. They may also have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace...
XCU03Z Parts Breakdown - Page 2
Model XCU03Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
810X87-6
002
183F24-8
002 C10 810R30...
424904-6
033
452666-6
034
234207-8
035
266326-2
036
424903-8
037
632H47-0
038
231298-0
XCU03 MODEL NO. LABEL HOUSING SET CAUTION LABEL INC. 28 TAPPING SCREW 4X18 FRONT HANDLE TAPPING SCREW 4X18 CATCH LEVER SWITCH LEVER TORSION ...
XCU03Z Parts Breakdown - Page 3
...BUMPER TAPPING SCREW 4X18 CHAIN CATCHER TAPPING SCREW 4X18 GUIDE PLATE ES TAPPING SCREW CT 3X8 GUIDE PLATE CS STRAIGHT BEVEL GEAR 14 ADJUST PIN ...ADJUST SCREW TAPPING SCREW 4X12 NUT COMPLETE NUT COVER SPROCKET COVER WHEEL COMPLETE O RING 7 O RING 10 GUIDE BAR CHAIN COVER SAW CHAIN SET
1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 1 PC. 1 PC. 4 PC. 1 PC. 2 PC....
Makita XCU03PT New Tool Flyers English - Page 1
... guard engineered to the Makita General Catalog or visit our website at only 100 dB(A) and zero emissions for operator comfort "Tool-less" chain adjustment for reduced operator fatigue
SPECIFICATIONS
Guide Bar Length Chain Speed Chain Pitch Chain Gauge Battery Overall Length UPC Code (XCU03Z) UPC Code (XCU03PT)
Also Available as a Bare Tool Model XCU03Z
14" 3,940...
Makita XCU03PT Reviews
We have not received any reviews for Makita yet.