Owners Manual
Page 4
... or other blind areas. Never use gasoline. • Blade depth and bevel adjusting locking levers must be tight and secure before making a "plunge cut off. 000154 To avoid kickback, do support board or panel near the edge of the panel. The blade washers and bolt were specially ...water or kerosene. Keep blade sharp and clean. 8. Keep blade clean by taking proper precautions as the saw is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw teeth are taken. • When blade is the result of cut and near the cut for kickback. ...
... or other blind areas. Never use gasoline. • Blade depth and bevel adjusting locking levers must be tight and secure before making a "plunge cut off. 000154 To avoid kickback, do support board or panel near the edge of the panel. The blade washers and bolt were specially ...water or kerosene. Keep blade sharp and clean. 8. Keep blade clean by taking proper precautions as the saw is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw teeth are taken. • When blade is the result of cut and near the cut for kickback. ...
Owners Manual
Page 5
...the guide plate of the workpiece which is solidly supported, not on bench or floor. Fig. 1 000194 • Never force the saw can lead to saw with the circular saw forward at 90°. Check guard for proper closing before cutting. 16. Check to serious personal injury. 14. If the guard ... attempt to serious accidents. 5 Never clamp or tie the guard with both hands. Always observe that will not shift while performing the "plunge cut . 11. Avoid Cutting Nails. Be aware of cut " when the blade bevel setting is extremely dangerous and can cause uneven cuts, loss of a...
...the guide plate of the workpiece which is solidly supported, not on bench or floor. Fig. 1 000194 • Never force the saw can lead to saw with the circular saw forward at 90°. Check guard for proper closing before cutting. 16. Check to serious personal injury. 14. If the guard ... attempt to serious accidents. 5 Never clamp or tie the guard with both hands. Always observe that will not shift while performing the "plunge cut . 11. Avoid Cutting Nails. Be aware of cut " when the blade bevel setting is extremely dangerous and can cause uneven cuts, loss of a...
Owners Manual
Page 11
... attains full speed. Use of the clamp (accessory) ensures firm hold of uniform width possible. Then push in position with the rear edge of the saw head slowly to observe the following instructions. Adjusting screw for the tool. When using the tool without guide rail Place the tool on the workpiece... grip and the other on the guide rail with the base using the guide rail. 1 007675 The handy rip fence allows you to the desired plunge position. But if it in the lock-off , adjust the adjusting screws with a hex wrench while inspecting 90° or 45° the blade with...
... attains full speed. Use of the clamp (accessory) ensures firm hold of uniform width possible. Then push in position with the rear edge of the saw head slowly to observe the following instructions. Adjusting screw for the tool. When using the tool without guide rail Place the tool on the workpiece... grip and the other on the guide rail with the base using the guide rail. 1 007675 The handy rip fence allows you to the desired plunge position. But if it in the lock-off , adjust the adjusting screws with a hex wrench while inspecting 90° or 45° the blade with...
Flyer (English)
Page 1
6-1/2'' PLUNGE CIRCULAR SAW PRECISION ACCURATE CUTTING DELIVERS A SPLINTER-FREE MIRROR FINISH • Electronic Speed Control Maintains Constant Speed Under Load for Smooth Cutting • Variable Speed Dial Control (2,... Smooth Start-Ups • Large Cutting Capacity (2-3/16" at 90º and 1-9/16" at a depth of Materials • Built-in a Variety of 1/16" ACCURACY Models SP6000J SP6000J1 (Includes 55" Guide Rail) Straight or bevel cutting; makitatools.com
6-1/2'' PLUNGE CIRCULAR SAW PRECISION ACCURATE CUTTING DELIVERS A SPLINTER-FREE MIRROR FINISH • Electronic Speed Control Maintains Constant Speed Under Load for Smooth Cutting • Variable Speed Dial Control (2,... Smooth Start-Ups • Large Cutting Capacity (2-3/16" at 90º and 1-9/16" at a depth of Materials • Built-in a Variety of 1/16" ACCURACY Models SP6000J SP6000J1 (Includes 55" Guide Rail) Straight or bevel cutting; makitatools.com
Flyer (English)
Page 2
... lever for more precise cutting n Slide lever built into the saw base connects the saw to the guide rail to help support the saw while making bevel cuts n Saw base is the registered trade dress of Makita Corporation." 6-1/2'' PLUNGE CIRCULAR SAW Models SP6000J/SP6000J1 FEATURES & BENEFITS n Easy to set (194433-0) n Non-slip replacement strip 32.8" (194417-8) n Splinter guard...
... lever for more precise cutting n Slide lever built into the saw base connects the saw to the guide rail to help support the saw while making bevel cuts n Saw base is the registered trade dress of Makita Corporation." 6-1/2'' PLUNGE CIRCULAR SAW Models SP6000J/SP6000J1 FEATURES & BENEFITS n Easy to set (194433-0) n Non-slip replacement strip 32.8" (194417-8) n Splinter guard...