Makita PH05R1 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita PH05R1 manuals!
Problems with Makita PH05R1?
Ask a Question
Free Makita PH05R1 manuals!
Problems with Makita PH05R1?
Ask a Question
Makita PH05R1 Videos
Makita PH05R1 Review - Hammer Driver-Drill Kit
Duration: 1:29
Total Views: 32
Duration: 1:29
Total Views: 32
MAKITA 12V max CXT™ 3/8" Hammer Driver-Drill Kit (PH05R1)
Duration: 1:54
Total Views: 8,128
Duration: 1:54
Total Views: 8,128
Popular Makita PH05R1 Manual Pages
PH05 Instruction Manual - Page 2
...use a power tool while you are doing and use any way. ENGLISH (Original instructions)
SPECIFICATIONS
Model: Drilling capacities
Fastening capacities No load speed (RPM)
Concrete Steel Wood Wood screw ...the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from heat, oil, sharp edges or moving parts. Save all instructions....
PH05 Instruction Manual - Page 3
... the battery; Cordless hammer driver drill safety warnings
1. Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may be caught in this instruction manual may create a risk of dust extraction and collection facilities, ensure these instructions to follow the safety rules stated in moving parts.
7. Take caution to noise...
PH05 Instruction Manual - Page 4
...Makita batteries. Use of non-genuine Makita batteries, or batteries that the tool is switched off and the battery cartridge is removed before installing or removing of battery. Charge the battery cartridge with any con-
It may reach or exceed 50 °C (122 °F). 7. SAVE THESE INSTRUCTIONS... out. Always stop operating immediately. Overcharging shortens the battery service life.
3.
PH05 Instruction Manual - Page 5
...Tool speed is operated in easily, it is equipped with "B" at a Makita service center. The tool will not operate. If you keep pulling the switch ...and the ambient temperature, the indication may accidentally fall out of the model number
1
2
► 1 . To start , the battery ...on again.
CAUTION: Always install the battery cartridge fully until the red indicator cannot be ...
PH05 Instruction Manual - Page 6
... change lever fully to the correct position before operating again. Reversing switch action
1
CAUTION: Always set the reversing switch lever to the "1" and restart the operation. The tool may be a little... the illumination. In this case, switch on lighting while the switch trigger is set the ring correctly to scratch the lens of rotation.
Position of rotation before operation...
PH05 Instruction Manual - Page 7
...
-
Turn the sleeve clockwise to open the chuck jaws. Close 3. The following shows the rough guide of the tool.
pine)
Hard wood
-
(e.g.
Screw
The hook is required for temporarily hanging the... torque at 20. To remove the driver bit/drill bit, turn the sleeve counterclockwise. Installing or removing driver bit/ drill bit
Optional accessory
Turn the sleeve counterclockwise ...
PH05 Instruction Manual - Page 8
... the desired location for the hole, then pull the switch trigger. Installing driver bit holder
Optional accessory
1
2
► 1 . Driver bit Fit the driver bit holder into the protrusion at the time of hole breakthrough, when...until it locks in position and prevent it fully until the red part cannot be aligned in . Screwdriving operation
CAUTION: Adjust the adjusting ring to you or someone...
PH05 Instruction Manual - Page 9
...Using holster
Optional accessory CAUTION: When using the holster, remove a
driver bit/drill bit from slipping when starting a hole, make an indentation... you do not hold -down device.
The guide screw makes drilling easier by setting the reversing switch to reverse rotation in order ...drill bit, decrease the tool performance and shorten the service life of the drill bit in the indentation and ...
PH05 Instruction Manual - Page 10
...or attempted by Makita Authorized or Factory Service Centers, always using Makita replacement parts. OPTIONAL ACCESSORIES
CAUTION: These accessories or attachments are required because of incidental or consequential damages, so the above limitation may not apply to persons.
If inspection shows the trouble is warranted to one of any trouble develop during this manual.
If you .
10...
PH05Z Parts Breakdown - Page 2
...-2 + SCREW M4X12
A02
346909-5 HOOK
E01
808F86-2 CAUTION LABEL
Q'ty Unit
1 0 1 8 PC. 1 2 PC. 1 PC. 1 PC. 1 PC. 1 1 0 1 3 PC. 1 1 PC. 1 1 1 0 1 PC. 1 1 Model PH05 Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part# Description
001
183C34-7 HOUSING SET
001 D10
INC. 17
002
851T68-7 PH05 NAME PLATE
003
266429-2 TAPPING SCREW 3X16
004
456532-9 SPEED CHANGE LEVER...
Makita PH05Z/PH05R1 New Tool Flyer English - Page 1
...Makita batteries and chargers
SPECIFICATIONS
Capacity masonry steel wood
No load speed (variable 2 speed) Blows Per Minute (2 speed) Maximum Torque Battery Overall length Net weight (with battery) UPC Code PH05R1 UPC Code... Brushless Motor delivers 280 in L.E.D. 12V max CXT™ Lithium-Ion Brushless Cordless 3/8" Hammer Driver-Drill Kit
Model PH05R1/PH05Z
Compact Brushless and Ergonomic Design...
Makita PH05R1 Reviews
We have not received any reviews for Makita yet.