Owners Manual
Page 2
... differ from tool before turning it was not designed. 2 MAKE WORKSHOP KID PROOF with Horizontal vise used) No load speed (RPM) Laser Type (LS1016L only) Dimensions (L x W x H) Net weight LS1016/LS1016L 255 mm (10") 15.88 mm (5/8") Bevel angle 0° 71 mm x 305 mm (2-13/16"x12") 91 mm x 279 mm (3-5/8"x11") 71...
... differ from tool before turning it was not designed. 2 MAKE WORKSHOP KID PROOF with Horizontal vise used) No load speed (RPM) Laser Type (LS1016L only) Dimensions (L x W x H) Net weight LS1016/LS1016L 255 mm (10") 15.88 mm (5/8") Bevel angle 0° 71 mm x 305 mm (2-13/16"x12") 91 mm x 279 mm (3-5/8"x11") 71...
Owners Manual
Page 9
...or cable any smaller than 6.35 mm (1/4") in unintentional operation and serious personal injury. Laser beam action For model LS1016L only 1. If the tool consistently fails to a Makita service center for insertion of a padlock to loss of the switch. With the adjusting screw loosened, slide the ... the saw blade by taping down or some other means. A switch in the lock-off button is not a substitute for padlock Makita service center. Electric brake This tool is equipped with an inoperative switch is equipped with an electronic speed control which prevents the tool...
...or cable any smaller than 6.35 mm (1/4") in unintentional operation and serious personal injury. Laser beam action For model LS1016L only 1. If the tool consistently fails to a Makita service center for insertion of a padlock to loss of the switch. With the adjusting screw loosened, slide the ... the saw blade by taping down or some other means. A switch in the lock-off button is not a substitute for padlock Makita service center. Electric brake This tool is equipped with an inoperative switch is equipped with an electronic speed control which prevents the tool...
Owners Manual
Page 23
... range further away from the pre-checked position. 5. Adjust the position of the laser line position For model LS1016L only 1. Workpiece 2. Laser line 1 Adjusting the laser line for the laser is changed by a Makita authorized service center for the left side of the tool may cause damage to see where the cutting...
... range further away from the pre-checked position. 5. Adjust the position of the laser line position For model LS1016L only 1. Workpiece 2. Laser line 1 Adjusting the laser line for the laser is changed by a Makita authorized service center for the left side of the tool may cause damage to see where the cutting...
Owners Manual
Page 24
...laser light carefully with machine oil to the instructions in the previously covered section titled "Blade guard". ACCESSORIES WARNING: • These Makita accessories or attachments are recommended for the laser light becomes dirty, or sawdust adheres to slip in serious personal injury. • Only... the slide pole is not working correctly, have the tool repaired by Makita Authorized or Factory Service Centers, always using a screwdriver. Screw (one piece only) 3. Cleaning the laser light lens For model LS1016L only 1. Loosen but do not remove the screw which secures the lens...
...laser light carefully with machine oil to the instructions in the previously covered section titled "Blade guard". ACCESSORIES WARNING: • These Makita accessories or attachments are recommended for the laser light becomes dirty, or sawdust adheres to slip in serious personal injury. • Only... the slide pole is not working correctly, have the tool repaired by Makita Authorized or Factory Service Centers, always using a screwdriver. Screw (one piece only) 3. Cleaning the laser light lens For model LS1016L only 1. Loosen but do not remove the screw which secures the lens...
Owners Manual
Page 25
...; Dust bag • Crown molding stopper set • Triangular rule • Dust box • Hex wrench (for LS1016L) MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is caused by others: repairs are required because of normal wear and tear: the tool has been abused, misused or... improperly maintained: alterations have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. Some states do not allow the exclusion or limitation of incidental or consequential ...
...; Dust bag • Crown molding stopper set • Triangular rule • Dust box • Hex wrench (for LS1016L) MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is caused by others: repairs are required because of normal wear and tear: the tool has been abused, misused or... improperly maintained: alterations have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. Some states do not allow the exclusion or limitation of incidental or consequential ...
Parts Breakdown
Page 5
...-9 231928-3 256633-1 231240-1 911113-1 262001-8 265717-4 266488-6 Parts Description TAPPING SCREW 4X18 REAR COVER CONTROLLER TAPPING SCREW 4X18 POWER SUPPLY CORD AWG#14-2-2.5 STRAIN RELIEF LS1016L NAME PLATE TAPPING SCREW 5X55 MOTOR BRACKET BAFFLE PLATE RETAINING RING S-17 BALL BEARING 6003DDW FAN 80 ARMATURE ASS'Y 115V INC. 131516 INSULATION WASHER BALL...
...-9 231928-3 256633-1 231240-1 911113-1 262001-8 265717-4 266488-6 Parts Description TAPPING SCREW 4X18 REAR COVER CONTROLLER TAPPING SCREW 4X18 POWER SUPPLY CORD AWG#14-2-2.5 STRAIN RELIEF LS1016L NAME PLATE TAPPING SCREW 5X55 MOTOR BRACKET BAFFLE PLATE RETAINING RING S-17 BALL BEARING 6003DDW FAN 80 ARMATURE ASS'Y 115V INC. 131516 INSULATION WASHER BALL...