Owners Manual
Page 7
...Adjusting screw 2 2. To tilt the blade to raise the handle fully. • After changing the miter angle, always secure the turn base by turning counterclockwise. With the release button depressed, tilt the saw blade, be sure to raise the handle fully. • After changing the bevel angle, always secure...the release button at the rear of the tool while tilting the blade slightly to the left to tilt the saw blade until the pointer points to the desired angle on the miter scale, securely tighten the grip clockwise. Turn base 1 2 2. Push the handle to position the kerf ...
...Adjusting screw 2 2. To tilt the blade to raise the handle fully. • After changing the miter angle, always secure the turn base by turning counterclockwise. With the release button depressed, tilt the saw blade, be sure to raise the handle fully. • After changing the bevel angle, always secure...the release button at the rear of the tool while tilting the blade slightly to the left to tilt the saw blade until the pointer points to the desired angle on the miter scale, securely tighten the grip clockwise. Turn base 1 2 2. Push the handle to position the kerf ...
Owners Manual
Page 9
... the side of the direct sunlight in compound cutting (bevel angle 45 degrees and miter angle right 45 degrees). NOTE: • When laser line is switched off and... the blade. Raise the blade guard and center cover. 003934 1. Wrench holder 1 2. Installing or removing saw blade 003923 1. A) When you obtain correct size on your workpiece with the laser line at the position ... line is switched off and unplugged before installing or removing the blade. • Use only the Makita socket wrench provided to the right of workpiece • Shift the laser line to install or remove...
... the side of the direct sunlight in compound cutting (bevel angle 45 degrees and miter angle right 45 degrees). NOTE: • When laser line is switched off and... the blade. Raise the blade guard and center cover. 003934 1. Wrench holder 1 2. Installing or removing saw blade 003923 1. A) When you obtain correct size on your workpiece with the laser line at the position ... line is switched off and unplugged before installing or removing the blade. • Use only the Makita socket wrench provided to the right of workpiece • Shift the laser line to install or remove...
Owners Manual
Page 12
...be impaired. • During a slide cut the workpiece. CAUTION: • Whenever performing the slide cut 002204 Loosen the lever and tilt the saw mark) in the following way. Bevel cut , FIRST PULL THE CARRIAGE TOWARD YOU FULLY and press down with the handle locked in the lowered... of the cut without the blade making any contact and wait until the blade attains full speed. Switch on the tool without stopping. Miter cutting Refer to secure the selected bevel angle safely. This may kickback unexpectedly with the potential to cause serious PERSONAL INJURY. • ...
...be impaired. • During a slide cut the workpiece. CAUTION: • Whenever performing the slide cut 002204 Loosen the lever and tilt the saw mark) in the following way. Bevel cut , FIRST PULL THE CARRIAGE TOWARD YOU FULLY and press down with the handle locked in the lowered... of the cut without the blade making any contact and wait until the blade attains full speed. Switch on the tool without stopping. Miter cutting Refer to secure the selected bevel angle safely. This may kickback unexpectedly with the potential to cause serious PERSONAL INJURY. • ...
Owners Manual
Page 13
... of the cut . Compound cutting can be cut on a compound miter saw blade. • During a bevel cut, it may be caught by the blade, causing fragments to the blade. A) and "Outside" 90° corners ((3) and (4) in the table. 006393 Miter angle Left and Right 45˚ Right 50˚ Right 55... molding 1 2 3 There are crown and cove molding joints which are two common types of crown moldings and one type of the saw angles. When cutting crown and cove moldings, set the bevel angle and miter angle as indicated in the table (A) and position the moldings on table to check the...
... of the cut . Compound cutting can be cut on a compound miter saw blade. • During a bevel cut, it may be caught by the blade, causing fragments to the blade. A) and "Outside" 90° corners ((3) and (4) in the table. 006393 Miter angle Left and Right 45˚ Right 50˚ Right 55... molding 1 2 3 There are crown and cove molding joints which are two common types of crown moldings and one type of the saw angles. When cutting crown and cove moldings, set the bevel angle and miter angle as indicated in the table (A) and position the moldings on table to check the...
Owners Manual
Page 14
...; Lay crown molding with its broad back (hidden) surface down on the turn base with its CEILING CONTACT EDGE against the guide fence on the saw . • The finished piece to be used will be on the RIGHT side of (2) blade. Example: In the case of blade. A: • Tilt and... secure bevel angle setting to 33.9° RIGHT. • Adjust and secure miter angle setting to 31.6° RIGHT. • Lay crown molding with its broad back (hidden) surface down on the turn base with its WALL CONTACT...
...; Lay crown molding with its broad back (hidden) surface down on the turn base with its CEILING CONTACT EDGE against the guide fence on the saw . • The finished piece to be used will be on the RIGHT side of (2) blade. Example: In the case of blade. A: • Tilt and... secure bevel angle setting to 33.9° RIGHT. • Adjust and secure miter angle setting to 31.6° RIGHT. • Lay crown molding with its broad back (hidden) surface down on the turn base with its WALL CONTACT...
Owners Manual
Page 15
Ceiling 52˚ 38˚ 000031 EN0002-1 Compound Miter Saw Miter and Bevel Angle Settings Wall Wall to Crown Molding Angle: 52/38 degrees Wall Angle ... 37.1 36.8 36.5 36.2 35.8 35.5 35.2 34.9 34.5 34.2 33.9 33.5 33.2 32.8 32.5 32.2 31.8 31.5 31.1 30.8 30.4 Miter Angle (deg.) 46.8 46.3 45.7 45.1 44.6 44.0 43.5 42.9 42.4 41.9 41.3 40.8 40.3 39.8 39.2 38.7 38.2 37.7 37.2 36... 23.2 22.8 22.5 22.1 21.7 21.3 21.0 20.6 20.2 19.8 19.5 19.1 18.7 18.3 17.9 17.6 17.2 16.8 16.4 16.0 15.8 Miter Angle (deg.) 26.9 26.5 26.1 25.7 25.3 24.9 24.5 24.1 23.7 23.3 22.9 22.6 22.2 21.8 21.4 21.0 20.7 20.3 19.9 ...
Ceiling 52˚ 38˚ 000031 EN0002-1 Compound Miter Saw Miter and Bevel Angle Settings Wall Wall to Crown Molding Angle: 52/38 degrees Wall Angle ... 37.1 36.8 36.5 36.2 35.8 35.5 35.2 34.9 34.5 34.2 33.9 33.5 33.2 32.8 32.5 32.2 31.8 31.5 31.1 30.8 30.4 Miter Angle (deg.) 46.8 46.3 45.7 45.1 44.6 44.0 43.5 42.9 42.4 41.9 41.3 40.8 40.3 39.8 39.2 38.7 38.2 37.7 37.2 36... 23.2 22.8 22.5 22.1 21.7 21.3 21.0 20.6 20.2 19.8 19.5 19.1 18.7 18.3 17.9 17.6 17.2 16.8 16.4 16.0 15.8 Miter Angle (deg.) 26.9 26.5 26.1 25.7 25.3 24.9 24.5 24.1 23.7 23.3 22.9 22.6 22.2 21.8 21.4 21.0 20.7 20.3 19.9 ...
Owners Manual
Page 16
Ceiling 45˚ 45˚ 000032 EN0003-1 Compound Miter Saw Miter and Bevel Angle Settings Wall Wall to Crown Molding Angle: 45 degrees Wall Angle (deg.) Bevel Angle (deg.) Miter Angle (deg.) Wall Angle (deg.) 60 37.8 50.8 101 61 37.5 50.2 102 62 37.3 49.6 103 63 37.1 49.1 104 64 36.8 48.5 105....3 22.0 21.7 21.4 21.0 20.7 20.4 20.0 19.7 19.4 19.1 18.7 18.4 18.1 17.7 17.4 17.1 16.7 16.4 16.0 15.7 15.4 15.0 14.7 14.3 14.0 Miter Angle (deg.) 30.2 29.8 29.4 28.9 28.5 28.1 27.6 27.2 26.8 26.3 25.9 25.5 25.1 24.7 24.3 23.8 23.4 23.0 22.6 22.2 21.8 21.4 21...
Ceiling 45˚ 45˚ 000032 EN0003-1 Compound Miter Saw Miter and Bevel Angle Settings Wall Wall to Crown Molding Angle: 45 degrees Wall Angle (deg.) Bevel Angle (deg.) Miter Angle (deg.) Wall Angle (deg.) 60 37.8 50.8 101 61 37.5 50.2 102 62 37.3 49.6 103 63 37.1 49.1 104 64 36.8 48.5 105....3 22.0 21.7 21.4 21.0 20.7 20.4 20.0 19.7 19.4 19.1 18.7 18.4 18.1 17.7 17.4 17.1 16.7 16.4 16.0 15.7 15.4 15.0 14.7 14.3 14.0 Miter Angle (deg.) 30.2 29.8 29.4 28.9 28.5 28.1 27.6 27.2 26.8 26.3 25.9 25.5 25.1 24.7 24.3 23.8 23.4 23.0 22.6 22.2 21.8 21.4 21...
Flyer (English)
Page 1
7-1/2" FOUR POLE SLIDE COMPOUND MITER SAW FOUR POLES WITH FOUR LINEAR BALL BEARINGS FOR A DEAD-ON ACCURATE CUT Precision Machined Aluminum Base Supports Large Stock for Efficient Cutting Conveniently Located Carrying ... motor head and provide deeper cutting capacity POWER 11-3/4" Capacity Precision machined aluminum base supports large stock with a maximum cutting capacity of 11-3/4" DURABILITY Model LS0714 Compact design (27.6 lbs.) and conveniently located carrying handle for jobsite portability JOBSITE PORTABILITY
7-1/2" FOUR POLE SLIDE COMPOUND MITER SAW FOUR POLES WITH FOUR LINEAR BALL BEARINGS FOR A DEAD-ON ACCURATE CUT Precision Machined Aluminum Base Supports Large Stock for Efficient Cutting Conveniently Located Carrying ... motor head and provide deeper cutting capacity POWER 11-3/4" Capacity Precision machined aluminum base supports large stock with a maximum cutting capacity of 11-3/4" DURABILITY Model LS0714 Compact design (27.6 lbs.) and conveniently located carrying handle for jobsite portability JOBSITE PORTABILITY
Flyer (English)
Page 2
... ■ Smooth easy slide system allows cross cuts up to the Makita General Catalog, or visit our website at 45° ■ Double sliding mechanism for our Compound Miter Saws. Master Carton Qty. 1 UPC Code 088381-05804-9 Model LS0714 Cutting Capacity Cuts Cross Miter Bevel Compound 0° 2-1/16"x11-3/4" 5° (Right) 1-9/16"x11-3/4" 45°...
... ■ Smooth easy slide system allows cross cuts up to the Makita General Catalog, or visit our website at 45° ■ Double sliding mechanism for our Compound Miter Saws. Master Carton Qty. 1 UPC Code 088381-05804-9 Model LS0714 Cutting Capacity Cuts Cross Miter Bevel Compound 0° 2-1/16"x11-3/4" 5° (Right) 1-9/16"x11-3/4" 45°...