Makita GCV02ZX Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita GCV02ZX manuals!
Problems with Makita GCV02ZX?
Ask a Question
Free Makita GCV02ZX manuals!
Problems with Makita GCV02ZX?
Ask a Question
Popular Makita GCV02ZX Manual Pages
Instruction Manual - Page 2
...Some of research and development, the specifications herein are shown in this manual.
SAFETY WARNINGS
WARNING
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, ...Use of the appliance and battery cartridge(s) are subject to a service center.
2 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model: Standard filter type Maximum air volume (with BL4040, ø...
Instruction Manual - Page 5
... battery life
1. 5. For commercial transports e.g. Installing the batteries to the handling of the battery... battery cartridge. Unless the tool supports the use near high-voltage electrical power...voltage electrical power lines. Overcharging shortens the battery service life.
3. When not using the battery ...INSTRUCTIONS. The battery cartridge can cause a large current flow, overheating,...
Instruction Manual - Page 9
... appliance to
restart. 2. Charge the battery(ies) or replace it to extend appliance and battery life. Caster 2. This... 3. Take all the following steps. • Press the power button to set the cleaner back in stand-by switch in the "I" (ON) or "AUTO...The suction power can be adjusted according to your local Makita Service Center. Lower the stopper lever by switch 2. Stand-by hand...
Instruction Manual - Page 15
...instruction manual of the tool when using the cleaner with wireless activation function.
Installing... metallic part, before installing the ...wireless unit. However the power button will be sure that the wireless unit is inserted in the figure. 1
Fig.28 ► 1 . NOTICE: Clean the dust and dirt on the tool.
NOTICE: To prevent the malfunction caused by switch is set...
Instruction Manual - Page 16
... tool, too. Install the batteries to the cleaner and the tool.
16 ENGLISH Set the stand-by ... to the instruction manual of the lid when removing the wireless unit. Tool registration for the cleaner
NOTE: A Makita tool supporting the wireless ... the power switch on the cleaner to the instruction manual of the wireless activation lamp.
Install the wireless units to the tool before starting ...
Instruction Manual - Page 17
...cleaner to "AUTO".
1
2
1 Fig.36 ► 1 .
Install the wireless units to the cleaner and the tool.
3.
In this case, set the stand-by switch on the cleaner to "AUTO" and press the ... activation lamp will stop the wireless activation, push the wireless activation button on the tool, or set the stand-by switch on the tool is a time lag when the cleaner detects a switch ...
Instruction Manual - Page 18
...) in red, release your finger from the wireless activation button.
Wireless activation button
3. Install the wireless unit to the cleaner.
3. When the wireless activation lamp lights up in red... all tool registrations
You can erase all tool registrations are erased. Wireless activation button 2. Set the stand-by switch 2. Press the wireless activation button on the tool in red after...
Instruction Manual - Page 19
...the meaning of the lamp status. running .
When the wireless activation button is not set in blue.
The power is supplied to be cancelled. Wireless activation lamp
The wireless ...1
2
Fig.39
► 1 .
The wireless activation lamp will automatically turn off when no operation is set to be registered.
(slow: 2 times/sec.) (fast: 5 times/sec.)
-
2 seconds 20 seconds...
Instruction Manual - Page 20
... for the Perform the tool registration procedures for repairs. and the cleaner at the same timing.
Set the stand-by switch on the tool has not been pushed. If you find a problem that the wireless activation lamp is not installed into the cleaner and/or the tool.
Install the wireless unit correctly. No power supply...
Instruction Manual - Page 21
...repairs... brushes, can be performed by Makita Authorized or Factory Service Centers, always using the cleaner for more than 6 ...replacement parts. The stand-by switch on the multi hook with the loose end tied up . Hold down the wireless activation button for erasing all tool registrations in large loops. Connect its root end installed in red and then release the button.
Set...
Instruction Manual - Page 22
...the powder filter, the prefilter and the damper with your Makita tool specified in this manual. They may result in poor suction performance. Fig.43
Cleaning of injury to persons.
... and a paddle. The use of any assistance for more details regarding these accessories, ask your local Makita Service Center. • Hose • Front cuffs (22, 24, 38) • Straight pipe •...
Instruction Manual - Page 23
If annexed warranty sheet is not available, refer to this product. MAKITA LIMITED WARRANTY
Please refer to the annexed warranty sheet for the most current warranty terms applicable to the warranty details set forth at below website for your respective country. United States of America: www.makitatools.com Canada: www.makita.ca Other countries: www.makita.com
23 ENGLISH
Parts Breakdown - Page 3
Model GCV02 ZU/ZX Parts List
Item#
Part#
Description
Q'ty
001
413B26-9 SWITCH BUTTON
1
002
234273-5
COMPRESSION SPRING 20
...-2
TAPPING SCREW 4X18
4
038
266326-2
TAPPING SCREW 4X18
4
039
183U06-0 TERMINAL CASE SET
2
039 D10
INC. 41
040
413B40-5 TERMINAL COVER
2
041
183U06-0 TERMINAL CASE SET
2
041 D10
INC. 39
042
232722-6
TENSION SPRING 4
4
043
632T08-2 TERMINAL ...
Parts Breakdown - Page 4
...SUPPORT RING REAR BLOCK FILTER A REAR BLOCK FILTER B TANK COVER COMPLETE BAND DUMPER A XGT LOGO LABEL TAPPING SCREW 4X18 HOOK COMPLETE SEAL RING LOWER TANK COVER TAPPING SCREW 4X25 POWDER FILTER H SET DAMPER SET PRE FILTER SET... CONNECTOR UNIT CAP COMPLETE O-RING16 CAP LABEL PAN HEAD SCREW M3X6 NOZZLE ASSEMBLY SET HOSE COMPLETE 28-3.5 SET CUFF LOCK STOPPER SLEEVE FRONT CUFF 38 FRONT CUFF 22
1 1
1
4...
Parts Breakdown - Page 5
...A12
195547-8
A12
195548-6
A13
195546-0
FRONT CUFF 24
1
HOSE COMPLETE 32-1.7 SET
1
HOSE COMPLETE 38-2.5 SET
1
CUFF LOCK
1
SLEEVE
2
FRONT CUFF
1
STOPPER
2
POLY BAG SET(650X650)
1
WIRELESS UNIT SET
1
TELESCOPIC PIPE COMPLETE SET 1
BENT PIPE ASSEMBLY
1
SLEEVE A
1
STOPPER A
1
LONG SASH NOZZLE SET 28 WHI 1
MULTI HOOK
1
STOPPER
1
PAN HEAD SCREW M4X18
1
FRONT CUFF 22...
Makita GCV02ZX Reviews
Do you have an experience with the Makita GCV02ZX that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!