Owners Manual
Page 3
...and high reliability. • Maintenance‑free electronic ignition, hermetically sealed to protect against dust and moisture. • Vibration damping with the MAKITA 2‑mass system (D2M) for tireless working even when guiding the Power Cut by hand. • Five-stage air-filter system for ...directly above the ground. • Extensive range of components 13 PUTTING INTO OPERATION Mounting the cutting disc 14 Tightening the V-belt / Checking V-belt tension 15 Installing the pressure water system 15-16 Fuels / Refuelling 16-17 Starting the engine 18 Cold-starting 19 Warm...
...and high reliability. • Maintenance‑free electronic ignition, hermetically sealed to protect against dust and moisture. • Vibration damping with the MAKITA 2‑mass system (D2M) for tireless working even when guiding the Power Cut by hand. • Five-stage air-filter system for ...directly above the ground. • Extensive range of components 13 PUTTING INTO OPERATION Mounting the cutting disc 14 Tightening the V-belt / Checking V-belt tension 15 Installing the pressure water system 15-16 Fuels / Refuelling 16-17 Starting the engine 18 Cold-starting 19 Warm...
Owners Manual
Page 6
... clothes. Eyes and skin should not come in contact with fuel, change protective clothes. Never use the Power Cut when it is properly mounted, the V-belt has the proper tension, the throttle moves easily and the halfthrottle lock button functions properly, the grips are wearing protective gear (see "Protective Equipment") (8). Keep...
... clothes. Eyes and skin should not come in contact with fuel, change protective clothes. Never use the Power Cut when it is properly mounted, the V-belt has the proper tension, the throttle moves easily and the halfthrottle lock button functions properly, the grips are wearing protective gear (see "Protective Equipment") (8). Keep...
Owners Manual
Page 7
... an accessory). - For masonry (cold cutting) WARNING! The cutting disc must not be well supported and securely held. Switch off the engine before inspecting the V-belt tension or tightening it with thumb and fingers). Switch off the Power Cut immediately if you have a safe footing. - Never change in the rear handle...
... an accessory). - For masonry (cold cutting) WARNING! The cutting disc must not be well supported and securely held. Switch off the engine before inspecting the V-belt tension or tightening it with thumb and fingers). Switch off the Power Cut immediately if you have a safe footing. - Never change in the rear handle...
Owners Manual
Page 12
... 0.2" 3) Cutting disc for 80 m/sec. 2) 4) Arbor diameter in 14" / 1" / 0.2" 3) in (mm) .020 (0.5) .020 (0.5) Fuel consumption at max. when using MAKITA Synthetic oil 50:1 50:1 - torque Nm 4.3 4.3 Idling speed 1/min 2,500 2,500 Clutch engagement speed 1/min 3,800 3,800 Engine speed limitation 1/min 9,400 ± 145 9,400...plug Type NGK BPMR 7A / BOSCH WSR 6F / CHAMPION RCJ 6Y Electrode gap in 0.8" 0.8" / 1.0" 5) V‑belt no. 965 300 470 965 300 470 Overall weight (tanks empty, without cutting disc) lb 22.04 22.48 2) ...
... 0.2" 3) Cutting disc for 80 m/sec. 2) 4) Arbor diameter in 14" / 1" / 0.2" 3) in (mm) .020 (0.5) .020 (0.5) Fuel consumption at max. when using MAKITA Synthetic oil 50:1 50:1 - torque Nm 4.3 4.3 Idling speed 1/min 2,500 2,500 Clutch engagement speed 1/min 3,800 3,800 Engine speed limitation 1/min 9,400 ± 145 9,400...plug Type NGK BPMR 7A / BOSCH WSR 6F / CHAMPION RCJ 6Y Electrode gap in 0.8" 0.8" / 1.0" 5) V‑belt no. 965 300 470 965 300 470 Overall weight (tanks empty, without cutting disc) lb 22.04 22.48 2) ...
Owners Manual
Page 13
... 10 24 23 22 EK7301 Identification plate (12) 1102 123456 Indicate when ordering spare parts EMI OFB 973108 Makita Corporation, Anjo, Aichi, Japan Made in Germany Serial number Year of manufacture 1 Handle 2 Filter cover for air filter and spark plug cap 3 Cover lock 4 Tubular handle 5 Muffler 6 Protection hood 7 Grip 8 V-belt tension adjusting screw...
... 10 24 23 22 EK7301 Identification plate (12) 1102 123456 Indicate when ordering spare parts EMI OFB 973108 Makita Corporation, Anjo, Aichi, Japan Made in Germany Serial number Year of manufacture 1 Handle 2 Filter cover for air filter and spark plug cap 3 Cover lock 4 Tubular handle 5 Muffler 6 Protection hood 7 Grip 8 V-belt tension adjusting screw...
Owners Manual
Page 14
... Power Cut on a stable surface and carry out the following work on the Power Cut! Turn the disc slowly until the stop hole of the V-belt pulley is marked on Cleaning / changing the air filter). Hinweis: The arbor hole of the package, knead it turns in the right direction, if a direction...
... Power Cut on a stable surface and carry out the following work on the Power Cut! Turn the disc slowly until the stop hole of the V-belt pulley is marked on Cleaning / changing the air filter). Hinweis: The arbor hole of the package, knead it turns in the right direction, if a direction...
Owners Manual
Page 15
... hood for maximum cutting performance with minimum fuel consumption. Tube routing with the cutting assembly in the middle position, see figure. - The belt tension is correctly adjusted when the nut (13) is centred on and tighten the coupling caps (21). Country-specific! Push clamp (22... cutting disk (see operator's manual). - Screw on the mark (14). NOTE: The water flow rate can be loosened before tightening the V-belt or checking the tension. NOTE: The two fastening nuts (11) must be precisely adjusted with the Power Cut. eter of operation! Connect the...
... hood for maximum cutting performance with minimum fuel consumption. Tube routing with the cutting assembly in the middle position, see figure. - The belt tension is correctly adjusted when the nut (13) is centred on and tighten the coupling caps (21). Country-specific! Push clamp (22... cutting disk (see operator's manual). - Screw on the mark (14). NOTE: The water flow rate can be loosened before tightening the V-belt or checking the tension. NOTE: The two fastening nuts (11) must be precisely adjusted with the Power Cut. eter of operation! Connect the...
Owners Manual
Page 21
... cover (4). Make sure to a certain amount of the screw (2) is visible in the reverse order. To tighten the V-belt see "Tightening the V-belt / Checking V-belt tension". 21 CAUTION: Start the Power Cut only after complete assembly and inspection. NOTE: Screw (5) is important for your... own safety that you have the unit checked and maintained regularly by a MAKITA service center before being used again! Remove the old belt (10) or belt pieces. Changing the V-belt Loosen nuts (3). Remove the screws (5) and (7) and remove the side piece (6). IMPORTANT: ...
... cover (4). Make sure to a certain amount of the screw (2) is visible in the reverse order. To tighten the V-belt see "Tightening the V-belt / Checking V-belt tension". 21 CAUTION: Start the Power Cut only after complete assembly and inspection. NOTE: Screw (5) is important for your... own safety that you have the unit checked and maintained regularly by a MAKITA service center before being used again! Remove the old belt (10) or belt pieces. Changing the V-belt Loosen nuts (3). Remove the screws (5) and (7) and remove the side piece (6). IMPORTANT: ...
Owners Manual
Page 27
...) and remove the cutting attachment. NOTE: The illustration shows the V-belt for DPC8132). Loosen and unscrew the screw (detail X, only for models EK7300, 7301. 12 27 Unscrew the grip (10) and turn the protective hood (11) ...
...) and remove the cutting attachment. NOTE: The illustration shows the V-belt for DPC8132). Loosen and unscrew the screw (detail X, only for models EK7300, 7301. 12 27 Unscrew the grip (10) and turn the protective hood (11) ...
Owners Manual
Page 28
... DPC8132). Screw on the cutting disc, make sure the disc turns in the right direction. To tighten the V-belt see "Tightening the V-belt / Checking Vbelt tension". Tighten the nuts (17) firmly with SLR muffler (EK7300, EK7301) Unscrew and remove screw (25). If a rotation direction is marked on nuts (17) and tighten by hand... wheel changes. Reassembly the spark arrester screen and tighten the screw. 13 15 14 18 16 17 25 26 28 NOTE: The illustration shows the V-belt for screen cleaning. Put the guard plate (16) on. Models with the combination wrench. Guide the...
... DPC8132). Screw on the cutting disc, make sure the disc turns in the right direction. To tighten the V-belt see "Tightening the V-belt / Checking Vbelt tension". Tighten the nuts (17) firmly with SLR muffler (EK7300, EK7301) Unscrew and remove screw (25). If a rotation direction is marked on nuts (17) and tighten by hand... wheel changes. Reassembly the spark arrester screen and tighten the screw. 13 15 14 18 16 17 25 26 28 NOTE: The illustration shows the V-belt for screen cleaning. Put the guard plate (16) on. Models with the combination wrench. Guide the...
Owners Manual
Page 30
... any maintenance work must not perform any liability damages arising from your nearest MAKITA service center. Failure to perform the prescribed maintenance work is right for the job 7 Check V‑belt tension 15 Adjust position Functional check Functional check Functional check 18 Check for damage...ensure proper air cooling Check for damage Check V‑belt tension, inspect for damage. Spare parts Reliable long-term operation, as well as the safety of your Power Cut, depend among other than original MAKITA spare parts are from the same production line as ...
... any maintenance work must not perform any liability damages arising from your nearest MAKITA service center. Failure to perform the prescribed maintenance work is right for the job 7 Check V‑belt tension 15 Adjust position Functional check Functional check Functional check 18 Check for damage...ensure proper air cooling Check for damage Check V‑belt tension, inspect for damage. Spare parts Reliable long-term operation, as well as the safety of your Power Cut, depend among other than original MAKITA spare parts are from the same production line as ...
Owners Manual
Page 33
..."/0.8") 966 144 120 1 Cutting disc for masonry, dia. 350/25,4 mm (14"/1.0") 3 994 280 250 1 Hex screw M8x25 4a 965 300 470 1 V-belt (for EK7300, 7301) 4b 965 300 481 1 V-belt (for DPC8131, 8132) 5 963 601 122 1 Suction head 6 010 114 091 1 Tank cap, compl. (fuel) 8 395 173 020 1 Inner filter 9 395... 4 - 949 000 035 1 - 980 008 627 1 - 980 008 628 1 Angle fuel‑tank filler neck, cpl. Extract from the spare parts list Use only original MAKITA parts. Guide trolley DT2000 cpl. For repairs and replacement of other parts, see your...
..."/0.8") 966 144 120 1 Cutting disc for masonry, dia. 350/25,4 mm (14"/1.0") 3 994 280 250 1 Hex screw M8x25 4a 965 300 470 1 V-belt (for EK7300, 7301) 4b 965 300 481 1 V-belt (for DPC8131, 8132) 5 963 601 122 1 Suction head 6 010 114 091 1 Tank cap, compl. (fuel) 8 395 173 020 1 Inner filter 9 395... 4 - 949 000 035 1 - 980 008 627 1 - 980 008 628 1 Angle fuel‑tank filler neck, cpl. Extract from the spare parts list Use only original MAKITA parts. Guide trolley DT2000 cpl. For repairs and replacement of other parts, see your...
Parts Breakdown
Page 11
... 3 162 001-182-042 DISC 1 163 010-180-024 CLUTCH ASSY. 1 164 024-184-021 SPRING 3 165 395-213-670 COVER 1 166 965-300-470 V-BELT 1 168 965-402-870 RUBBER PLATE 1 169 325-341-611 HOOD 1 169 394-341-051 HOOD 1 170 957-342-011 MOUNTING, CPL. 1 171 394-342...-975 SAFETY LABEL 1 202 394-213-021 METAL SHEET 1 204 962-300-017 NEEDLE BUSH 1 205 928-405-000 DISC 1 206 326-341-300 GRIP 1 EK7301 EM4251 Page 11 of 14 PB_08-2011_rev 0 Corresponding bulletins are listed in subsiding order with the newest version on top not indented. Select bulletin name...
... 3 162 001-182-042 DISC 1 163 010-180-024 CLUTCH ASSY. 1 164 024-184-021 SPRING 3 165 395-213-670 COVER 1 166 965-300-470 V-BELT 1 168 965-402-870 RUBBER PLATE 1 169 325-341-611 HOOD 1 169 394-341-051 HOOD 1 170 957-342-011 MOUNTING, CPL. 1 171 394-342...-975 SAFETY LABEL 1 202 394-213-021 METAL SHEET 1 204 962-300-017 NEEDLE BUSH 1 205 928-405-000 DISC 1 206 326-341-300 GRIP 1 EK7301 EM4251 Page 11 of 14 PB_08-2011_rev 0 Corresponding bulletins are listed in subsiding order with the newest version on top not indented. Select bulletin name...
Parts Breakdown
Page 12
...-151-480 SPRING 1 266 038-111-060 SQUARE NUT 1 267 378-151-220 SCREW 4 268 395-171-024 TUBE 1 269 038-131-070 HOSE CLIP 1 EK7301 EM4251 Page 12 of 14 PB_08-2011_rev 0 N Part No. Corresponding bulletins are listed in subsiding order with multiple versions are attached. Select bulletin name or...-202 TANK CAP CPL. 1 217 963-229-036 PACKING RING 2 218 395-211-640 COVER CPL. 1 219 395-211-620 COVER 1 221 394-221-050 BELT PULLEY 1 223 395-160-600 STARTER ASS'Y BLUE, DPC7331 1 224 395-160-630 STARTER CASE BLUE, DPC7331 1 225 181-164-010 STARTER KNOB 1 226 181...
...-151-480 SPRING 1 266 038-111-060 SQUARE NUT 1 267 378-151-220 SCREW 4 268 395-171-024 TUBE 1 269 038-131-070 HOSE CLIP 1 EK7301 EM4251 Page 12 of 14 PB_08-2011_rev 0 N Part No. Corresponding bulletins are listed in subsiding order with multiple versions are attached. Select bulletin name or...-202 TANK CAP CPL. 1 217 963-229-036 PACKING RING 2 218 395-211-640 COVER CPL. 1 219 395-211-620 COVER 1 221 394-221-050 BELT PULLEY 1 223 395-160-600 STARTER ASS'Y BLUE, DPC7331 1 224 395-160-630 STARTER CASE BLUE, DPC7331 1 225 181-164-010 STARTER KNOB 1 226 181...