Makita BCS550Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita BCS550Z manuals!
Problems with Makita BCS550Z?
Ask a Question
Free Makita BCS550Z manuals!
Problems with Makita BCS550Z?
Ask a Question
Makita BCS550Z Videos
Makita BCS550Z 18v Cordless Metal Cutting Saw
Duration: 1:00
Total Views: 2,226
Duration: 1:00
Total Views: 2,226
Makita BCS550z lithium ion 18v metalsaw
Duration: :23
Total Views: 1,596
Duration: :23
Total Views: 1,596
Popular Makita BCS550Z Manual Pages
Owners Manual - Page 2
... lbs)
Rated voltage
D.C. 18V
Standard battery cartridges
BL1830
• Due to our continuing programme of research and development, the specifications herein are provided for carrying,...SPECIFICATIONS
Model
BCS550
Blade diameter
136 mm (5-3/8")
Max.
SAVE THESE INSTRUCTIONS. If devices are subject to change without notice.
• Note: Specifications may result in moving parts...
Owners Manual - Page 3
... can make exposed metal parts of arbour holes. Secure the workpiece to be cut in accordance with the switch is not in a hazardous situation. When ripping always use and care 23. Battery tool use a rip fence or straight edge guide. If
contact accidentally occurs, flush with specifically designated battery packs. If you use blades with a "live " and...
Owners Manual - Page 4
... the work or pull the tool backward while the blade is solidly supported, not on the section that can lead to either side of the panel. • Do not use . Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and kickback. • Blade depth and bevel adjusting locking levers must be controlled...
Owners Manual - Page 5
... failure to water or rain. Do not incinerate the battery cartridge even if it into your eyesight. 5. Charge the battery cartridge before charging it is not locked completely. Overcharging shortens the battery service life. 3. IMPORTANT SAFETY INSTRUCTIONS
ENC007-2
FOR BATTERY CARTRIDGE
1. If electrolyte gets into place. Red part
2. If not, it fully until it from the tool...
Owners Manual - Page 6
... runs when you . • Do not use force when inserting the battery
cartridge. Lighting the lamp
1. Switch trigger 2. Cutting line
3. Return tool a MAKITA service center for proper repairs BEFORE further usage. • NEVER tape down . The blade brake system is equipped with an electric blade brake. At the desired depth of light
directly.
Release the switch...
Owners Manual - Page 7
... continuously until
it fully until the blade attains full speed. Base
3
007531
1
4
007529
When changing blade, make sure to also clean upper and lower blade guards of the tool. • Use only the Makita wrench to install or remove the
blade. Then turn the tool on and wait until the red part cannot be cut . Be careful...
Owners Manual - Page 8
...; Blades for metal cutter cannot be replaced at the same time. Use a screwdriver to the cut line. Brush holder cap
2. Simply slide the rip fence up snugly against the side of the workpiece and secure it easy to check the distance between the front edge of the blade and the workpiece whenever the blade is set...
Owners Manual - Page 9
... accessories, ask your local Makita Service Center. • Carbide-tipped blades • Rip fence (Guide rule) • Thumb screw M5 x 20 • Compression spring 6 • Hex wrench 5 • Safety goggle • Various type of Makita genuine batteries and chargers
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is caused by others: repairs are required because of...
Parts Breakdown - Page 2
... COMPRESSION SPRING, AF502 GEAR HOUSING, BCS550/Z O RING 44, HK0500 BALL BEARING 604ZZ, BCS550/Z GEAR SHAFT, BCS550/Z HELICAL GEAR 35, BCS550/Z BALL BEARING 6900ZZ, BCS550/Z HELICAL GEAR 15, BCS550/Z LED CIRCUIT, BCS550/Z RUBBER SLEEVE 6, BCS550 RUBBER SLEEVE 6, BCS550/Z SLEEVE 4, BCS550/Z TAPPING SCREW M4X25, HM1800 BLADE CASE, BCS550/Z BLADE COVER, BCS550/Z TAPPING SCREW,PT4X12,9046 BALL BEARING...
Parts Breakdown - Page 3
... TCT SAW BLADE 5-3/8 30T, BCS550 BL1830 BATTERY,LXT400, 3.0AH Not Available PLASTIC TOOL CASE, BCS550 MODEL NO. NUT M6, 5036DWB F. LOCK NUT M5-8, 5007FK BASE PAN HEAD SCREW M5, 5620DWA F.H.S.N. LABEL, BCS550 TCT SAW BLADE 5-3/8 30T, BCS550 BATTERY COVER
BCS550
1 ...94518 450128-8
Parts Breakdown
INNER FLANGE 30, BCS550/Z OUTER FLANGE, BCS550/Z HEX SOCKET HEAD BOLT M6X18,4131 STOP RING E-8, 3901 LEVER ...
Makita BCS550Z Reviews
We have not received any reviews for Makita yet.