Makita 6922NB Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita 6922NB manuals!
Problems with Makita 6922NB?
Ask a Question
Free Makita 6922NB manuals!
Problems with Makita 6922NB?
Ask a Question
Popular Makita 6922NB Manual Pages
Owners Manual - Page 1
... kg,m 1593 Ibs,ft)
No loadspeed IRPMI 26 18
Dimensions (L x W x H)
241 mm x 84 mm x 246 mm (9-112'' x 3-5/16" x 9-11/16")
249 mm x 84 mm x 252 mm 19-13/16" x 3-5/16" x 9-15/16")
Net weight
4.3 kg (9.5 lbsl
4 . 8 kg (10.6 Ibsl Shear Wrench
MODEL 6920NB MODEL 6922NB
INSTRUCTION MANUAL
DOUBLE
lNSULATlON
Model 6920NB 6922N8
Bolt size
5/8". 314" (A4901
5/13",3 4 " . 7/8"
(A4901
Max...
Owners Manual - Page 2
... clean for lubricating and changing acces- Inspect extension cords periodically and replace if damaged. Cluttered areas and benches invite injuries. 2. DON'T FORCE TOOL. Use clamps or a vise t o hold work area well lit. rized service facility. IMPORTANT SAFETY INSTRUCTIONS
(For All Tools)
WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE...
Owners Manual - Page 3
... shock, this instruction manual. Before further use tool if switch does not turn it still does not fit, contact a qualified electrician t o install the proper outlet. Don't use of parts, mounting, and any way.
3 POLARIZED PLUGS. Do not change the plug in a polarized outlet only one blade is damaged should be properly repaired or replaced by authorized service center. Check...
Owners Manual - Page 4
... on the , nameplate of sheared bolt tips. If in SERIOUS INJURY t o the user - Using a power source with voltage greater than the nameplate rating is below when using the tool in high or ...good balance and firm footing. Use care and common sense w h e n disposing of the tool.
VOLTAGE WARNING: Before connecting the tool to the motor. SAVE THESE INSTRUCTIONS.
4 Falling tips from high ...
Owners Manual - Page 5
... inner sleeves. The outer and inner sleeves
I f you need other sizes for your work, replace the sleeves as follows.
The outer sleeve M20 and inner sleeve 3/4" are factory-installed. Place the outer sleeve over the inner sleeve.
Removing or installing t h e outer and inner sleeves CAUTION : *Always be pushed up by the springs built...
Owners Manual - Page 6
See the figure below. Switch action To start the tool, simply pull the trigger.
The outer sleeve turns to the "OFF" position when released. Bolt installation Slip the tool onto the bolt so that it further forward until there i s no longer fit inside the sleeve properly. CAUTION : Be careful when fitting ...
Owners Manual - Page 7
... from falling dangerously below.
Bolt tip
7
,
..I I When the specified torque is attained, the
' bolt tip will remain inside the inner sleeve. Catch the sheared bolt tips to prevent injury from the tool. The bolt tip will be sheared at its notched portion.
Keep the tips off of the ground, floor, walkways, etc.
Owners Manual - Page 8
Brush holder c
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
8 Both carbon brushes should be replaced a t the same time. Use only identical carbon brushes.
Use a screwdriver to slip in the holders.
Keep the carbon brushes ...
Owners Manual - Page 9
SHEAR WRENCH Model 6920NB Model 6922NB
- Fob 1 0 - ' 9 4 US
Note: The switch, noise suppressor and other part configuratlons may differ from country 10 country
9
Owners Manual - Page 12
... of Makita's Factory or Authorized Service Ceniers. If inspection shows the trouble is caused by defeftivc workmanship 01 material, Makita will rcplir (or at o u r Option.
THIS DISCLAIMER
APPLIES BOT11 DlJRlNC AND AFTER T H E T E R M OF THIS WARRANTY. Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi 446 Japan
883878A066
PRINTED IN JAPAN 1994-3-N This Warranty gives you specific...
Parts Breakdown - Page 2
... SPUR GEAR 14, 6922NB PIN 4, 6922NB WASHER 2542, 6922NB T.N. BOLT M4X14, 6922NB GEAR CASE COMPLETE, 6922NB RUBBER PIN 4, HR2400 BALL BEARING 698, 6922NB HELICAL GEAR 30, 6922NB THRUST NEEDLE, 6922NB
Page 2 of 3
Quantity 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 4 4 4 4 4 1 4 4 2 4 4 4 4 4 1 4 1 1 4 1 1 1 1 1 1 1 1 1 1 2 4 1 1 1 1 1 4 1 1 1 1 1
8/18/2010 Parts Breakdown
6922NB
Products with...
Parts Breakdown - Page 3
...-4 819031-6 819083-7 232146-6 322788-5 324447-7
421497-4 257941-3 267282-9 153909-6
764319-8 764360-1
764322-9 764348-1
764418-6 783001-0 150479-6 823276-0 810146-2
Parts Breakdown
BALL BEARING 6000LLB, 5740NB FAN 55, 6922NB ARMATURE ASS'Y 115V, 6922NB INS. BEARING 627LB, 6510LVR PROTECTOR, 6922NB BRUSH CAP , 9031 CARBON BRUSH 408 SET, 3901 CARBON BRUSH SET CB-408, KP0800K
MOTOR HOUSING COMP...
Makita 6922NB Reviews
Do you have an experience with the Makita 6922NB that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!