Mackie Onyx FireWire Support and Manuals
Get Help and Manuals for this Mackie item
View All Support Options Below
Free Mackie Onyx FireWire manuals!
Problems with Mackie Onyx FireWire?
Ask a Question
Free Mackie Onyx FireWire manuals!
Problems with Mackie Onyx FireWire?
Ask a Question
Mackie Onyx FireWire Videos
Mackie Onyx FireWire Mixers
Duration: 8:07
Total Views: 41,448
Duration: 8:07
Total Views: 41,448
Popular Mackie Onyx FireWire Manual Pages
Owner's Manual - Page 1
FIREWIRE OPTION CARD
for ONYX MIXERS
OWNER'S MANUAL
Owner's Manual - Page 3
...A: Service Information 34
Troubleshooting...34 Repair...35
Appendix B: Technical Info 36
Onyx FireWire Card Specifications 36
Onyx FireWire Card Limited Warranty 38
Don't forget to visit our website at www.mackie.com for more information about this and other Mackie products. Part No.
B 03/12 ©2004-2012 LOUD Technologies Inc. All Rights Reserved. SW0133 Rev. Owner's Manual
3
Owner's Manual - Page 4
... :
Date of audio back to the Onyx mixer, which you can select in the Control Room Source matrix for routing to connect the Onyx FireWire interface anywhere within a chain of Tracktion, our easyto-use multitrack recording and sequencing software for the PC and Mac. ONYX FireWire Card
Introduction
Thank you for choosing to upgrade your computer. You select the...
Owner's Manual - Page 5
... you may be possible to replace a 4200 rpm drive with the manufacturer to make sure. However, if you should check with a faster one of tracks, specify a faster drive. For the PC:
• Windows XP (no earlier operating systems are buying a laptop to use the Onyx FireWire interface.
Owner's Manual
5 Owner's Manual
System Requirements
These are the minimum...
Owner's Manual - Page 6
....: "MACKIE", "ONYX", AND THE "RUNNING MAN" FIGURE • US PATENT NUMBER 29/049,129
POWER ON
~100-240 VAC 50/60 Hz 80W
RECORDING OUTS
1-8
POST GAIN PRE INSERT
9-16
(BALANCED)
(BALANCED)
OO OO
OPTION CARD
3. DO NOT REMOVE COVER. Use an anti-static wrist strap when performing this installation. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO...
Owner's Manual - Page 7
... INSERT
12 INSERT
11 INSERT
10 INSERT
9 INSERT
8 INSERT
7 INSERT
6 INSERT
5 INSERT
4 INSERT
3 INSERT
2 INSERT
1 INSERT
edge of the card.
UN- UN- UN- Two more screws are two supporting "legs" on the back of Onyx FireWire Card
5. UN- UN-
UN- UN- Slide the FireWire card into the bottom of the Onyx mixer and secure the two supporting legs on the
back...
Owner's Manual - Page 8
... > Browse" and navigate to your CD drive. 2. The Mackie Onyx FireWire Driver Setup win- Do not connect the FireWire card to the CD drive. We'll tell you to set the sample rate and adjust the latency (delay) of the audio passing through the FireWire card. Insert the CD provided with the Onyx FireWire card into your computer yet! Open the "Control
Panel" folder...
Owner's Manual - Page 11
... "Found New Hardware Wizard" opens. Select "Install the software automatically" option (default) and click "Next." Turn on the FireWire bus.
10. Owner's Manual
11
We'll have two Onyx mixers with the FireWire card installed, and the FireWire cable (included) connected to your computer. NOTE: DO NOT CLICK EITHER BUTTON in this point. The next window tells you have to your computer...
Owner's Manual - Page 12
The "Found New Hardware Wizard" opens again to install the Onyx FireWire Sub C driver. ONYX FireWire Card
11. When the wizard indicates that the installation is finished, click "Finish."
12. Select "Install the software automatically" option, and click "Next."
12
ONYX FireWire Card
Owner's Manual - Page 13
... turn it on the first FireWire card.
14. Owner's Manual
13
After completing step 13 for the second mixer. Repeat steps 10 through 13 for the second mixer (or the first mixer, if you only have a second Onyx mixer with a FireWire card installed, it is time to connect it to one ), click "I Completed the Above Steps" in the Mackie Onyx FireWire Driver Setup window. Now, if you can...
Owner's Manual - Page 15
... and the latency setting. If you are not used.
Inputs 13 through 16 are using one Onyx mixer with any DAW application that a connection is established with the Onyx FireWire Card(s), and allows you have installed on your computer. To open the Onyx FireWire Control Panel, click "Start > Programs > Mackie Onyx > Onyx Control Panel."
If using an Onyx 1220, the FireWire card still...
Owner's Manual - Page 16
..."Audio MIDI Setup."
16
ONYX FireWire Card ONYX FireWire Card
If using two Onyx mixers with FireWire cards:
It is necessary to www.mackie.com/OnyxFW_Update for details of what system version and FireWire components are recording a session over a period of time, it . If you retain the correct order of its time in the DAW application. Go to turn that the Onyx FireWire card is recognized by...
Owner's Manual - Page 34
... the answer to the problem without having to increase the ASIO (PC) or Core Audio (Mac) latency setting.
Tracktion: Click the Settings tab and then click Audio Devices.
Visit the Support section of our website (www.mackie.com/support) where you will find lots of useful information such as you did when installing the drivers.
34
ONYX FireWire Card On the PC...
Owner's Manual - Page 37
.... Owner's Manual
37
For more information about where you can drop off your waste equipment for recycling waste electrical and electronic equipment (EEE). OO
MAX MAIN MIX TRIM
A
B
7.5 in/191 mm
LISTED ACCESSORY FOR USE WITH ONYX MIXERS 65HJ
Top of Onyx FireWire Card
WEIGHT 8.3 oz/ 235 g
3.6 in /222 mm
24-BIT/96kHz MULTI-CHANNEL FIREWIRE I/O OPTION CARD
DESIGNED...
Owner's Manual - Page 38
... our website and follow the instructions for reporting a warranty issue and submitting a request for service time and parts.
• Ship the product in BIG PRINT on top of this warranty.
To obtain repairs or replacement under warranty.
38
ONYX FireWire Card Have your sales receipt in its option, will ship a replacement unit to an authorized service center. The return ground...
Mackie Onyx FireWire Reviews
We have not received any reviews for Mackie yet.