Mackie M2000/M3000/M4000 Support and Manuals
Get Help and Manuals for this Mackie item
This item is in your list!
View All Support Options Below
Free Mackie M2000/M3000/M4000 manuals!
Problems with Mackie M2000/M3000/M4000?
Ask a Question
Free Mackie M2000/M3000/M4000 manuals!
Problems with Mackie M2000/M3000/M4000?
Ask a Question
Popular Mackie M2000/M3000/M4000 Manual Pages
M-Series Owner's Manual - Page 2
.... If the user decides to construct speaker cabling (using the instructions provided later in this apparatus near any way, such as set forth here. To ensure against potentially dangerous exposure to equipment capable of the obsolete outlet.
10. M-Series
Important Safety Instructions
1. Install in susceptibility to noise-induced hearing loss, but nearly everyone will...
M-Series Owner's Manual - Page 3
......16 Input Wiring...17 Output Wiring...18
Appendix A: Service Information 21
Warranty Service...21 Troubleshooting ...21 Repair ...22
Appendix B: Technical Info 23
M-Series Specifications ...23 M-Series Dimensions...24 M-Series Block Diagram...26
M-Series Limited Warranty 27
Don't forget to visit our website at www.mackie.com for more information about this and other...
M-Series Owner's Manual - Page 4
... appreciate your new amplifier hooked up diagrams that number in our manuals. The bottom line is a Quick-Start Guide to help from the output devices evenly and efficiently, to the extensive protection circuits designed to the Mackie exclusive adaptive slew Class-H switching design that make your selection of features...
M-Series Owner's Manual - Page 5
... together to the CHANNEL 2's red post. Connect nothing into PROTECT mode. Owner's Manual
5 Turn the POWER switch off.
5. If you did! In MONO and BRIDGE...setup for OverLoad) are blinking.
14. Slowly turn down the channel Gain controls.
2. If the topmost LEDs (named OL, for amplifying stereo signals.
• MONO mode (sometimes called Bridged-Mono - Connections and Settings...
M-Series Owner's Manual - Page 7
...
2 INPUT
HIGH EFFICIENCY POWER AMPLIFIER SERIAL / DATE CODE
AC LINE BREAKER
(PUSH TO...Manual
Hookup Diagrams
OPTIONAL CONNECTION USING BINDING POSTS
TO SPEAKERS
FROM MIXING CONSOLE LEFT AND RIGHT MAIN OUT
SPEAKER OUTPUTS + BRIDGE
+
+
CAUTION LETHAL
VOLTAGES MAY APPEAR AT OUTPUT TERMINALS.
Passive Speakers (Mackie...Manual
7 The Amp Mode switch is set to the high-frequency driver...
M-Series Owner's Manual - Page 9
... POWER AMPLIFIER SERIAL / DATE CODE
AC LINE...Mackie S410s)
This drawing shows how to use the X-over switches on Amplifier 1 are set... to HPF and both channels pass frequencies below 150 Hz to the loudspeakers. The Thru connections pass the full-range signals on to power a stereo two-way system without using an external crossover. CLASS 3 WIRING IS REQUIRED.
Owner's Manual...
M-Series Owner's Manual - Page 10
...;er controls, you'll typically determine the optimal settings during peak moments.
Overloading, or clipping, occurs when the output voltage no longer linearly follows the input voltage and simply stops. Fear not...the amp at normal signal levels, while the OL LED may flicker occasionally during installation or sound check, then leave them alone, using the amplifier as a control ...
M-Series Owner's Manual - Page 11
... operate. If you've got a set of the following situations: improper ventilation,...for the power amplifier. Owner's Manual
3. That, of a problem that can sometimes occur when powering up to... until you ! If a "short" is a Mackie exclusive and can cause the PROTECT circuit to engage ...short" indication would be able to keep your troubleshooting time. You may overheat. Note: Since ...
M-Series Owner's Manual - Page 13
...ers, each set . Each ...GND
HIGH EFFICIENCY POWER AMPLIFIER
1 INPUT
2 INPUT
HPF
SERIAL / DATE CODE
LPF
FULL
150Hz
X-...MACKIE" AND
LIMIT
THE "RUNNING MAN" FIGURE ARE REGISTERED TRADEMARKS OF LOUD TECHNOLOGIES INC.
~
Owner's Manual...amplifying stereo signals.
See "Input Wiring" on , daisy-chaining as many amps as well), you a choice -
A general rule of thumb is the typical setup...
M-Series Owner's Manual - Page 14
...INPUT
HIGH EFFICIENCY POWER AMPLIFIER SERIAL / DATE CODE
AC LINE BREAKER
...(PUSH TO RESET)
HPF
LPF
FULL
150Hz
X-OVER
ON/ TYPICAL
CAUTION
RISK OF ELECTRIC SHOCK • DO NOT OPEN
OFF
LIMIT
OFF
LIMIT
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA MANUFACTURED IN CHINA • FABRIQUE EN CHINE ©2005 LOUD TECHNOLOGIES INC. • "MACKIE... MODE switch set to MONO to...
M-Series Owner's Manual - Page 15
...The LIMITER works independently on page 16 for a replacement. Square waves sound awful, and could possibly damage your speakers and/or your particular model. The LIMITER is 2 ohms or greater (... not a problem.
In a live sound application, the sound of an 18 gauge cord. Owner's Manual
even notice any audible difference. Clipping occurs when the output voltage no longer linearly follows the...
M-Series Owner's Manual - Page 16
... power cord. In addition, because of the weight of the amplifier, you must secure the rear support brackets of the amplifier to balance the temperature along the entire length of all the internal components. ...crest factor and the duty cycle of the rack. When designing your model.
The M•3000 and M•4000 require 19.5" depth inside the rack, including the rear...
M-Series Owner's Manual - Page 21
... signal level from the depriva- Owner's Manual
Appendix A: Service Information
Warranty Service
Details concerning Warranty Service are working properly.
If the breaker pops again, there may be a problem with your M-Series amplifier has a problem,
• Is the OVER TEMP [5] LED lit? Slowly turn the power switch off . Troubleshooting
• Is the PROTECT [3] LED...
M-Series Owner's Manual - Page 22
... cable between the mixer and the amplifier. Repair
Service for any damage that all forms of the problem, including how to repair the amplifier.
4. Call Tech Support at : techmail@mackie.com Keep this owner's manual and the detachable linecord. This is covered for a warranty repair. You will ship it back, pre-paid (if it...
M-Series Owner's Manual - Page 27
... to the original purchaser and to LOUD Technologies that the Service Request Number is received for repair or replacement of purchase in a safe place. by an authorized service center. or its authorized service centers may use refurbished parts for labor, materials, return freight, and insurance.
Call Mackie Technical Support at our option, require proof of the original date...
Mackie M2000/M3000/M4000 Reviews
Do you have an experience with the Mackie M2000/M3000/M4000 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Mackie yet.
Earn 750 points for your review!