Precision-9 Compass Installation Guide
Page 2
... earth's magnetic field is significantly different from a dedicated Calibration section in different locations. 2 | Precision-9 Installation Guide Setup To achieve the best possible performance, the compass should be calibrated, and any offsets should be done from an appropriate display unit. Wiring The Precision-9 compass is connected to configure the Precision-9, please check if there is a software update available...
... earth's magnetic field is significantly different from a dedicated Calibration section in different locations. 2 | Precision-9 Installation Guide Setup To achieve the best possible performance, the compass should be calibrated, and any offsets should be done from an appropriate display unit. Wiring The Precision-9 compass is connected to configure the Precision-9, please check if there is a software update available...
Precision-9 Compass Installation Guide
Page 3
... necessary to Locked once you can see the current calibration status in whenever they are satisfied with slightly different behavior. Precision-9 Installation Guide | 3 The default mode is Auto, and for first calibration is not yet collected. Locked In this mode, the compass will not change its calibration, you are deemed better than the current ones...
... necessary to Locked once you can see the current calibration status in whenever they are satisfied with slightly different behavior. Precision-9 Installation Guide | 3 The default mode is Auto, and for first calibration is not yet collected. Locked In this mode, the compass will not change its calibration, you are deemed better than the current ones...
Precision-9 Compass Installation Guide
Page 4
...another 390 degree turn 2-3°/second. Offsets An offset can use method 2 above to start manual calibration. For roll and pitch, offsets should be set so that both the compass heading and the bearing to a visible object. x 1. Allow time for any difference between the... boat's center line (A) and the compass lubber line (B). This offset is applied to the compass. ¼¼ Note: If you use method 1 to compensate for the heading and bearing values to the NMEA 2000 network. 4 | Precision-9 Installation Guide Use a chart or a chart ...
...another 390 degree turn 2-3°/second. Offsets An offset can use method 2 above to start manual calibration. For roll and pitch, offsets should be set so that both the compass heading and the bearing to a visible object. x 1. Allow time for any difference between the... boat's center line (A) and the compass lubber line (B). This offset is applied to the compass. ¼¼ Note: If you use method 1 to compensate for the heading and bearing values to the NMEA 2000 network. 4 | Precision-9 Installation Guide Use a chart or a chart ...
Precision-9 Compass Installation Guide
Page 6
with random excitation of ± 10° at a rate of 90° at max 1 Hz: - NMEA 2000 ports (input/output): Calibration: Repeatability: Roll/Pitch range: Heading accuracy: Dynamic performance: - NMEA 2000 Load Equivalence No. (LEN): - bracket: Supply and interface: Power consumption: - module... 119 mm (4.69") 165 g (5.8 oz) 130 g (4.6 oz) 8-16 V via NMEA 2000 0.4 W 1 1 Automatic ± 1.0° (or better) ± 45° ± 2° after calibration Heading error Technical specifications Dimensions: Weight: - with heading step input of 10°/s: Environmental protection...
with random excitation of ± 10° at a rate of 90° at max 1 Hz: - NMEA 2000 ports (input/output): Calibration: Repeatability: Roll/Pitch range: Heading accuracy: Dynamic performance: - NMEA 2000 Load Equivalence No. (LEN): - bracket: Supply and interface: Power consumption: - module... 119 mm (4.69") 165 g (5.8 oz) 130 g (4.6 oz) 8-16 V via NMEA 2000 0.4 W 1 1 Automatic ± 1.0° (or better) ± 45° ± 2° after calibration Heading error Technical specifications Dimensions: Weight: - with heading step input of 10°/s: Environmental protection...