LiftMaster MTS Support and Manuals
Get Help and Manuals for this LiftMaster item
View All Support Options Below
Free LiftMaster MTS manuals!
Problems with LiftMaster MTS?
Ask a Question
Free LiftMaster MTS manuals!
Problems with LiftMaster MTS?
Ask a Question
Popular LiftMaster MTS Manual Pages
Installation Manual - Page 1
SURFACE MOUNT MTF - FLUSH MOUNT IN-GROUND
INSTALLATION MANUAL
RREINCACELDUIIVDOEEDR
• THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED GATE SYSTEMS TECHNICIAN ONLY. Use (2) LiftMaster 12 Vdc 7AH (Part # MBAT). IMPORTANT: Read and understand Warranty Page first. Batteries (included) MUST be connected for proper operation of operator. MATTS MOTORIZED TRAFFIC CONTROL DC ...
Installation Manual - Page 2
... UL325 Model Classifications UL325 Entrapment Protection Requirements Safety Installation Information
2
3 INSTALL THE TRAFFIC LIGHT
19
3
4 OPERATION AND MAINTENANCE
20
INTRODUCTION
5-6 Important Safety Instructions
20
General Service
20
Important Information for Installation of All Traffic Spike Systems
5 Shear Pin Replacement
20
Features, Tools Needed, and Operator Specifications...
Installation Manual - Page 3
... a means to service the general public. The gate is able to www.P65Warnings.ca.gov
UL325 MODEL CLASSIFICATIONS
CLASS I
... use separate entrance.
3 NOTE: UL requires that all installations must use in plain view on both sides of the ...parts by security personnel. CLASS III - For more single family units) hotel, garage, retail store or other restricted access locations not servicing...
Installation Manual - Page 5
... the area of the barriers. SIGNAGE • Warning signs are strongly recommended to warn drivers of the inherent danger of the device, including a notice for repairing malfunctions or replacing parts resulting from improper installation or use. Failure to strictly follow these installation instructions will not be sure to puncture tires of wrong-way traffic, and a multitude of...
Installation Manual - Page 6
... Head) • Cable Cutters and Strippers
OPERATOR SPECIFICATIONS This model is intended for use in vehicular gate applications.
• Intended Usage Class II, III, IV
• High torque 24 volt Permanent Magnet DC motor
• On 120 Vac installations, unswitched duplex outlet gives convenient supply for easy troubleshooting. • Adjustable Timer-To-Close with...
Installation Manual - Page 7
...codes before or after the units. 6. All conduits must not be limited to 1/2" (1.3 cm) when possible to make sure there are no obstructions in the traffic lane and check for your anchors per manufacturer's instructions...closest part of the gate arm and support shall have a lateral offset of at the end of asphalt (tarmac) road surfaces. 1. Traffic controllers must be when installed. Bolt...
Installation Manual - Page 8
...around the outside unit to set and cured, unbolt the leveling-handles and replace the bolts in place,...INSTALLATION
TOOLS NEEDED FOR FLUSH MOUNT INSTALLATIONS
• Excavation and cement mixing equipment: water, shovel, wheelbarrow, flat-trowel
Tunnel
• 1 yard of 3000 PSI premix cement
• Crushed rock
• 6 to 18 open
position, the closest part of the gate arm and support...
Installation Manual - Page 14
...manual or wiring diagrams for the antenna. To prevent possible SERIOUS INJURY or DEATH, the use TV Type F coaxial connectors. Failure to install a reversing edge under these circumstances may use with a wireless control panel (Model... to the terminals and space for specific wiring information.
To prevent possible SERIOUS...controls, all LEDs will replace the first programmed accessory....
Installation Manual - Page 15
...remote control
that case, repeat the programming. THERE ARE NO USER SERVICEABLE PARTS. PROGRAMMING
PROGRAM A SINGLE BUTTON REMOTE CONTROL 1 Press and release the...seconds. 2 Within 30 seconds press and hold the Learn button for instructions on the remote
control.
This device complies with FCC and/or Industry...specifications you will need a transformer (Model 85LM plug-in or 95LM wired-in).
Installation Manual - Page 18
...from the gate. The gate MUST reverse on the limit cam. SAVE THESE INSTRUCTIONS.
18 If arm is obstructed while opening then the IRD is obstructed while closing...set at the limits: Move the limit cam closer to adjust and retest the gate operator properly can be performed by qualified service persons only. Have a qualified service person make repairs....
2. Read the owner's manual.
Installation Manual - Page 19
... chain
2. Too much chain tension will be installed in line and should be in the turnbuckles ...the rollers to the left turnbuckle
9. Manually spin the MAT pulley to the left, the ...the threaded shafts so that holds the guide roller assembly under the
gate opener. ...be adjusted by loosening the two set screws. Service Side
7. Tighten allen/set screws.
Route the long
chain ...
Installation Manual - Page 20
...Replacement must be 27.5 +0.05, -0 Vdc disconnected (set with a number 6 taper only.)
NEVER USE A BOLT AS A TEMPORARY FIX, THIS WILL DAMAGE THE SHAFT AND COLLAR.
1. Turn the S3 Manual... recommended that support motor to the up ...Repeat ALL procedures. GENERAL SERVICE
• If the ...Manual Open switch to CLOSE to install batteries correctly will cause damage and will not be replaced...
Installation Manual - Page 24
... processor and program are running properly. To allow gate to be opened or closed during service of operator. Close Loop Back Away - Shows that AC power is present. D14:...Vdc regulated rated at 500 ma. [1/2 amp]. S3: Manual open. Free Exit Loop Shadow Loop Commons - 0Vdc
Open Limit Sensor Open Drivers On Motor Brake On Close Drivers On
Close Limit Sensor Obstruction Sense
(IRD and MRT)...
Installation Manual - Page 25
...weak the gate will begin to run timer settings are too weak
to conserve batteries in this...Replace if blown. Yes
Allow operator to reset. Inspect the belt for 5 to close. Turn off . NOTE: If LED D12 does light, gate will clear low battery indicator.
TROUBLESHOOTING...
connections.
DISCONNECT BATTERIES AND AC POWER BEFORE SERVICING ANY MECHANICAL OR MOVING COMPONENTS. Yes
Is...
Installation Manual - Page 26
... Operator Cover Installation and Service Manual Arm Bolts with Washers Nylon Nuts 7AH Batteries
MATTS TOWER UNIQUE PARTS LIST
QTY
ITEM PART NUMBER DESCRIPTION
1
*
MA020T
Operator Cover for MATTS Tower
1
*
MA020D
Operator Door for MATTS (Not Tower) Nylon Arm Nuts (2) Arm Bolts (2) Gate Arm - 12' Filter Module Surge Suppressor Collar Nylon Washer
NOT SHOWN - REPAIR PARTS
10...
LiftMaster MTS Reviews
We have not received any reviews for LiftMaster yet.