LevelOne GSW-4876 Support and Manuals
Get Help and Manuals for this LevelOne item
View All Support Options Below
Free LevelOne GSW-4876 manuals!
Problems with LevelOne GSW-4876?
Ask a Question
Free LevelOne GSW-4876 manuals!
Problems with LevelOne GSW-4876?
Ask a Question
Popular LevelOne GSW-4876 Manual Pages
EU Declaration of Conformity - Page 1
Product Trade name Model Number
: Ethernet switch : Level One : GEP-5070,GSW-4876
Applicable Harmonized Standards
: EN 55022:2010 / CISPR 22:2008 Class A : EN... CE
Declaration of Conformity
We herewith confirm the following designated products to comply with the requirements set out in responsible for marking this declaration:
Amanda(Shu-Wen) Chen Name (Full Name)
Geschaftsfuhrerin Title/...
Manual - Page 3
MANAGEMENT GUIDE
GSW-4876 WEB SMART SWITCH
Layer 2 Gigabit Ethernet Switch with 48 10/100/1000BASE-T Ports (RJ-45) and 2 Gigabit Combination (RJ-45/SFP) Ports
GSW-4876 E082012/ST-R01
Manual - Page 11
...-based VLANs Displaying Information About Flow Sampling
6 PERFORMING BASIC DIAGNOSTICS Pinging an IPv4 or IPv6 Address Running Cable Diagnostics
7 PERFORMING SYSTEM MAINTENANCE Restarting the Switch Restoring Factory Defaults Upgrading Firmware Activating the Alternate Image
- 11 -
CONTENTS
250 251 251 254 255 256 256 257 258 259 259 260 261 262 262 263 264 265...
Manual - Page 25
...level of traffic are exceeded. Trunks can unobtrusively mirror traffic from overwhelming the network.When enabled on an interface. The switch supports up or dynamically configured using Link Aggregation Control Protocol (LACP - When a static address is configured on this port to specific network resources or protocols. PORT CONFIGURATION
You can be manually set...and source IP on VLAN...
Manual - Page 28
... Port Security IP Filtering HTTP Server HTTP Port Number HTTP Secure Server HTTP Secure Server Redirect
Default "admin" "admin" Disabled Disabled Disabled Enabled Enabled Disabled Disabled Enabled 80 Disabled Disabled
- 28 -
To reset the switch defaults, this file should be transmitted across a single network-wide multicast VLAN shared by setting the required priority level for IPv6...
Manual - Page 37
... groups
169
Ports
Specifies default PVID and VLAN attributes
170
Mirroring & RSPAN Sets source and target ports for... and location
45
IP
Configures IPv4 and SNTP settings
46
IPv6
Configures IPv6 and SNTP settings
48
NTP
Enables ...settings
56
Security
58
Switch
58
Users
Configures user names, passwords, and access levels
58
Privilege Levels Configures privilege level for specific...
Manual - Page 43
... the cable length
Maintenance
283
Restart Device
Restarts the switch
283
Factory Defaults
Restores factory default settings
284
Software
Upload
Updates software on the switch with a file specified on the 284 management station
Image Select
Displays information about the active and alternate (backup) 285 firmware images in the switch, and allows you to revert to the alternate image...
Manual - Page 56
... or manually setting the speed and duplex mode, enabling flow control, setting the maximum frame size, specifying the response to abnormal behavior (e.g., excessive collisions), and then reenable it after the problem has been resolved. The following options are displayed: ◆ Link - Disables the interface. Supports 10 Mbps half-duplex operation (Default: Autonegotiation...
Manual - Page 65
... switch supports both current Telnet sessions and SSH sessions. The maximum number of client sessions includes both SSH Version 1.5 and 2.0 clients.
◆ SSH service on the management station to install an SSH client on this switch as specified on the switch. (Default: Enabled)
WEB INTERFACE To configure SSH: 1. To use SSH with a local user name and password for...
Manual - Page 68
... that supports SNMP versions 1, 2c, and 3. Click Save. Figure 18: Access Management Configuration
USING SIMPLE NETWORK
MANAGEMENT
PROTOCOL
Simple Network Management Protocol (SNMP) is controlled by a security model and specified security levels. These objects are three security models defined, SNMPv1, SNMPv2c, and SNMPv3. Access to a specific address range.
6. Access to set of...
Manual - Page 69
... SHA algorithms and data privacy using DES 56-bit encryption
NOTE: The predefined default groups and view can then define customized groups and views for SNMP. The following table shows the security models and levels available and the system default settings. The switch has a default view (all MIB objects) and default groups defined for security models v1 and v2c.
Manual - Page 149
.... ◆ QI - This feature is the Max Response Time advertised in multiples of 10; Default: 2) Routers adopt the robustness value from receiving a multicast service when no report. (Range: 1-255; CHAPTER 4 | Configuring the Switch IGMP Snooping
but the interface settings will not take effect until snooping is used to inform other devices of the maximum...
Manual - Page 163
... the Switch Link Layer Discovery Protocol
■ Trailing street suffix - Additional location information.
(Example: South Wing) ■ Name - Postal/zip code. (Example: 2791) ■ Building - Building (structure). (Example: Low Library) ■ Apartment - Floor. (Example: 4) ■ Room no . - Emergency Call Service (e.g. 911 and others), such as used for a set of service...
Manual - Page 210
..., the UPnP discovery protocol allows that device to broadcast its services to search for "GSW-4876" will appear in UPnP networking is to -live (TTL) value for presentation, then the control point can send actions to the device's service. To access or manage the switch with the aid of device attributes advertised through UPnP. When...
Manual - Page 284
...Click the Upload button to upgrade the switch's system firmware by specifying a file provided by LevelOne. Click Maintenance, Factory Defaults. 2. Note that no reboot is necessary. The factory defaults are immediately restored, which means that the LAN IP Address, Subnet Mask and Gateway IP Address will be reset to restore the original factory settings. Click the Browse button, and...
LevelOne GSW-4876 Reviews
We have not received any reviews for LevelOne yet.