Lantronix FOX3 Series Support and Manuals
Get Help and Manuals for this Lantronix item
This item is in your list!
View All Support Options Below
Free Lantronix FOX3 Series manuals!
Problems with Lantronix FOX3 Series?
Ask a Question
Free Lantronix FOX3 Series manuals!
Problems with Lantronix FOX3 Series?
Ask a Question
Popular Lantronix FOX3 Series Manual Pages
Hardware Manual - Page 3
.../aboutus/contact/
Revision History
Date
Rev. Lantronix grants you no right to receive source code to the terms of the applicable license. The GNU General Public License is subject to the Open Source software; Your use of the setting/option "Load-VCP" after installing the FTDI driver.
19/02/2015
1.0.8 Unnamed: PAID-FEATURE in chapter...
Hardware Manual - Page 6
...GPRS Coding scheme...49
10. Federal Communications Commission (FCC) Compliance Statement 50 10.1.1. ISED RF Exposure Information 51
FOX3-2G/3G/4G Series Hardware Manual
6 Inserting a SIM card into the SIM holder 35 7.3.1. Audio Interface...45
8. Housing ...47 9. Appendix 48
9.1. Installation guidance...48
9.2. ISED Notice ...50 10.4. Setting up a USB connection for FOX3-2G...
Hardware Manual - Page 38
... Data +
Complies to the USB 2.0 specifications
7
Detect USB
Detects the connection to USB cable and install the driver. Connect the FOX3-2G/3G/4G to a free USB port on your PC via your PC. Hardware Interfaces
1
MOSI
Output
Master output, slave input
2
USB_V+
Input / Output Power supply for Driver Software",
FOX3-2G/3G/4G Series Hardware Manual
38
PFAL Command Reference - Page 41
... PFAL COMMANDS
4.2.2. Initializes remote firmware update
Command syntax Examples
Sys.RUpdate.Init,,,,, $PFAL,Sys.RUpdate.Init,FW_raw,new,890812,14,raw_cfg
FIRMWARE
DEVICES FOX3-2G
FOX3-3G
FOX3-4G
BOLERO40
2.16.x 3.0.x 3.1.x 3.2.x MODELS Std. It can be set to use these commands without special care.
Except the information found in
this document, Lantronix will be received...
PFAL Command Reference - Page 108
...
Command syntax Examples
Sys.Can.DTCO.SendAPDU,,"codes" $PFAL,Sys.Can.DTCO.SendAPDU,0xee,"0x10 0x7e"
FIRMWARE
DEVICES FOX3-2G
FOX3-3G
FOX3-4G
BOLERO40
2.16.x 3.0.x 3.1.x 3.2.x MODELS Std. PFAL Command Reference
108 PFAL COMMANDS
PFAL
Command description This command requests a Diagnostic Trouble Code message (DTC) on the 1st CAN port...
PFAL Command Reference - Page 140
..., $PFAL,Sys.NFC.LED
FIRMWARE
DEVICES FOX3-2G
FOX3-3G
FOX3-4G
BOLERO40
2.16.x 3.0.x 3.1.x 3.2.x MODELS Std. It specifies the configuration type of LED indicator to the High level.
Min.
Sys.NFC.LED -
lpulse, Performs a single low pulse for the specified time. The value may range between 0 and 255. Sets LED behaviours on the Lantronix NFC reader. Parameter...
PFAL Command Reference - Page 226
...FIRMWARE
DEVICES FOX3-2G
FOX3-3G
FOX3-4G
BOLERO40
2.16.x 3.0.x 3.1.x 3.2.x MODELS Std.
GSM.MCC - Gets the current mobile country code
Command syntax Examples
GSM.MCC $PFAL,GSM.MCC
FIRMWARE
DEVICES FOX3-2G
FOX3-3G
FOX3-4G
BOLERO40
2.16.x 3.0.x 3.1.x 3.2.x MODELS... supported.
4.7.1.9.
GSM.USSD -
Std. USSD is network-dependent and depends on the specific services ...
PFAL Command Reference - Page 241
... syntax Examples
GSM.Audio.SMSSignalToneMode= $PFAL,GSM.Audio.SMSSignalToneMode=1
FIRMWARE
DEVICES FOX3-2G
FOX3-3G
FOX3-4G
BOLERO40
2.16.x 3.0.x 3.1.x 3.2.x MODELS Std.
Notes:
This command does NOT affect stored audio profile settings.
In order to permanently keep the selected audio settings, such settings must be stored to an audio profile - else they are...
PFAL Command Reference - Page 304
...MODELS Std. CONFIGURATION SETTINGS
Set configuration Get configuration
$PFAL,Cnf.Set,DEVICE.COMM.BINEVENT0=,0D,e $PFAL,Cnf.Set,DEVICE.COMM.BINEVENT1="0x41,0x42",43,i $PFAL,Cnf.Set,DEVICE.COMM.BINEVENT0="0x44,0x30",0D,e // for IDs (Tags) that start with the user text
DEVICE.COMM.BINEVENT
FIRMWARE
DEVICES FOX3 Series
FOX3-3G Series
FOX3-4G Series BOLERO40 Series
2.16.x 3.0.x 3.1.x
MODELS...
PFAL Command Reference - Page 328
...,20
//disabled //"auto" mode //"doze" mode
Get configuration $PFAL,Cnf.Get,DEVICE.LOWPOWER
FIRMWARE
DEVICES FOX3-2G
FOX3-3G
FOX3-4G
BOLERO40
2.16.x 3.0.x 3.1.x 3.2.x MODELS Std. This setting defines the power mode in stand-by state.
DEVICE.LOWPOWER
Parameter syntax DEVICE.LOWPOWER=,,
This parameter sets the device into a low power mode.
Defines the amount of time, in full...
PFAL Command Reference - Page 356
... operator ID of a specific provider e.g. 26203
How ...SETTINGS
not support GPRS services, the current operator will be found.
i.e. 262 for operators within the desired country and finds a GSM operator there, the PFAL command PFAL,GSM.MMC can be changed. fixed, GSM engine starts with any available operator, but it is possible to the any $PFAL,Cnf.Set,GSM.OPERATOR.SELECTION=manual...
PFAL Command Reference - Page 378
..." server).
Specifies the TCP port number used for example www.lantronix.com) instead of the IP-address until one is returned) ...set /requested:
Set configuration
$PFAL,Cnf.Set,TCP.CLIENT.CONNECT=1,217.119.194.35,2222
Get configuration
$PFAL,Cnf.Get,TCP.CLIENT.CONNECT
FIRMWARE
DEVICES FOX3-2G
FOX3-3G
FOX3-4G
BOLERO40
2.16.x 3.0.x 3.1.x 3.2.x MODELS Std. CONFIGURATION SETTINGS...
PFAL Command Reference - Page 393
..., an Error event occurs. IP address in the hostname form (for example www.lantronix.com) instead of a dynamic or static IP-address. See also chapter 2.3. CONFIGURATION SETTINGS
5.12....and then execute manually (if is automatically done.
PFAL Command Reference
393 TCP.CLIENT2.CONNECT
Parameter syntax
TCP.CLIENT2.CONNECT=,,
This parameter specifies a second TCP port setup. After a ...
PFAL Command Reference - Page 422
....67340,10.98060,50.67350,10.98070 $PFAL,Cnf.Set,GF1=area8000,"Lantronix Office",C,50.67340,10.98060,482,100
Get configuration $PFAL,Cnf.Get,GF1
FIRMWARE
DEVICES FOX3-2G
FOX3-3G
FOX3-4G
BOLERO40
2.16.x 3.0.x 3.1.x 3.2.x MODELS Std.
Longitude, in decimal format.
Std. Based on the earth. function Supports
Latitude, in decimal format. Specifies the Upper Right corner...
PFAL Command Reference - Page 537
...11.4. Supported character sets
APPENDIX...set . Such a character is not ASCII alphabet! GSM 03.38 character
Ö " ò @
GSM character hex. In this problem is the terminal equipment that does not support the GSM default alphabet. This way you write characters differently coded in the range from the use of the GSM alphabet:
"@" character with the firmware 2.5.0 supports...
Lantronix FOX3 Series Reviews
Do you have an experience with the Lantronix FOX3 Series that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Lantronix yet.
Earn 750 points for your review!