Service Manual
Page 11
Thermal cut off. Idler switch Measure resistance of the following terminal : "COM - "NC" (1-3) Terminal : "COM" - Outlet Thermostat ( Auto reset) • Check Top Marking : N85 4. to terminal be sure to turn the power off • Check Top Marking...COM" - CAUTION When checking the Component, be replaced Safety Open at 149 ± 9°F (65 ± 5°C) Same shape as Outlet Thermostat. Hi limit Thermostat (Auto reset) 3. Lever push (close) Resistance value ∞ 10 5 COMPONENT TESTING INFORMATION ! Resistance value ∞ Resistance value < 5Ω ...
Thermal cut off. Idler switch Measure resistance of the following terminal : "COM - "NC" (1-3) Terminal : "COM" - Outlet Thermostat ( Auto reset) • Check Top Marking : N85 4. to terminal be sure to turn the power off • Check Top Marking...COM" - CAUTION When checking the Component, be replaced Safety Open at 149 ± 9°F (65 ± 5°C) Same shape as Outlet Thermostat. Hi limit Thermostat (Auto reset) 3. Lever push (close) Resistance value ∞ 10 5 COMPONENT TESTING INFORMATION ! Resistance value ∞ Resistance value < 5Ω ...
Service Manual
Page 13
Outlet Thermostat (Manual reset) • Check Top Marking : N100 Test Procedure Measure resistance of terminal to terminal Open at 203 ± 7°F (95 ± 5°C) Close at ... ± 7°C) Manual reset If thermal fuse is open must be replaced Resistance value ∞ Continuity < 1Ω • Gas type • Gas funnel 12 Outlet Thermostat (Auto reset) • Check Top Marking : N95 13. Component 13.
Outlet Thermostat (Manual reset) • Check Top Marking : N100 Test Procedure Measure resistance of terminal to terminal Open at 203 ± 7°F (95 ± 5°C) Close at ... ± 7°C) Manual reset If thermal fuse is open must be replaced Resistance value ∞ Continuity < 1Ω • Gas type • Gas funnel 12 Outlet Thermostat (Auto reset) • Check Top Marking : N95 13. Component 13.
Service Manual
Page 17
...°F (45°C) • Above : 1" on , 1" off beep sound • Under : 0.5" on, 0.5" off ) 2. Activating the Heater manually with damp cloth. is open may trip the Thermostat attached to the Heater, therefore do not activate it manually. (Do not press the door switch to operate the heater while the door is increasing...
...°F (45°C) • Above : 1" on , 1" off beep sound • Under : 0.5" on, 0.5" off ) 2. Activating the Heater manually with damp cloth. is open may trip the Thermostat attached to the Heater, therefore do not activate it manually. (Do not press the door switch to operate the heater while the door is increasing...
Service Manual
Page 20
...resistance below 1Ω between Connector "WH3- NO YES • Replace Control. (Relay check) • Check Controller connector. • Replace Outlet • Thermostat. (Refer to 'Component') • Check Idler Assembly. • Drum Belt cuts off • Drum Belt takes off , and do voltage discharge. ...(When discharging, contact the metal plug of Outlet Thermostat attached to Motor Bracket operate Level by drum belt? Test 3 Motor test Caution Before measuring resistance, be sure to turn Power off...
...resistance below 1Ω between Connector "WH3- NO YES • Replace Control. (Relay check) • Check Controller connector. • Replace Outlet • Thermostat. (Refer to 'Component') • Check Idler Assembly. • Drum Belt cuts off • Drum Belt takes off , and do voltage discharge. ...(When discharging, contact the metal plug of Outlet Thermostat attached to Motor Bracket operate Level by drum belt? Test 3 Motor test Caution Before measuring resistance, be sure to turn Power off...
Service Manual
Page 23
...NO • Replace Heater. NO YES • Replace TH3 (HI-Limit Thermostat). Is resistance between Heater terminal and below 18 ~ 22Ω? 2. NO YES • Replace TH2 (Safety Thermostat). YES Check Controller. Check Harness-linking Connector. 22 Electric Type Caution Before ... Power cord with earth line.) Trouble Symptom While operating, Heating will not work. Is resistance between terminal TH2 (Safety Thermostat). Measurement Condition After turning Power off , and do voltage discharge. (When discharging, contact the metal plug of measured resistance...
...NO • Replace Heater. NO YES • Replace TH3 (HI-Limit Thermostat). Is resistance between Heater terminal and below 18 ~ 22Ω? 2. NO YES • Replace TH2 (Safety Thermostat). YES Check Controller. Check Harness-linking Connector. 22 Electric Type Caution Before ... Power cord with earth line.) Trouble Symptom While operating, Heating will not work. Is resistance between terminal TH2 (Safety Thermostat). Measurement Condition After turning Power off , and do voltage discharge. (When discharging, contact the metal plug of measured resistance...
Service Manual
Page 24
... check • Controller change 23 Drying time takes longer. Test 7 GAS Valve test - Trouble Symptom While operating, Heating will not work. YES NO • Check thermostat Hi limit Safety Igniter operates? (after 1 min, Igniter becomes reddish) YES NO • Check Igniter & Frame detect When measuring Valve 2 voltage, Value is more than...
... check • Controller change 23 Drying time takes longer. Test 7 GAS Valve test - Trouble Symptom While operating, Heating will not work. YES NO • Check thermostat Hi limit Safety Igniter operates? (after 1 min, Igniter becomes reddish) YES NO • Check Igniter & Frame detect When measuring Valve 2 voltage, Value is more than...