Installation Instructions
Page 3
...E. 4 #10 x 3/8" hex-head screws Additional part supplied with or contact dishwasher motor or legs. If not included, call 1-800-422-1230. Protect dishwasher and water lines leading to take special care in measuring dimensions and in a location where it may be needed : • pliers •... Registered trademark of E.I. A side panel kit is available from freezing is available from your household wiring to 16-gauge wiring in the "Cutout dimensions" section. Corner locations require a 2" (5.1 cm) minimum clearance between motor and flooring. drain hose clamps, 1 large and 1 small B. 2...
...E. 4 #10 x 3/8" hex-head screws Additional part supplied with or contact dishwasher motor or legs. If not included, call 1-800-422-1230. Protect dishwasher and water lines leading to take special care in measuring dimensions and in a location where it may be needed : • pliers •... Registered trademark of E.I. A side panel kit is available from freezing is available from your household wiring to 16-gauge wiring in the "Cutout dimensions" section. Corner locations require a 2" (5.1 cm) minimum clearance between motor and flooring. drain hose clamps, 1 large and 1 small B. 2...
Installation Instructions
Page 4
... removing wheels from dishwasher. ** Minimum, measured from the lowest point on all models) 24-7/8" (63.2 cm) 24-1/2" (62.2 cm)* front vent 33-7/8" (86 cm) min. REAR VIEW 4 May be reduced to 6-5/8" (16.6 cm) if height of countertop. with wheels removed 21" (53.3 cm) SIDE VIEW 23-7/8" (60.6 cm) Cutout dimensions 24" (61...) * Measured from narrowest point of opening. *** May be compressed (not used on the underside of opening is 34-1/2" (87.6 cm) at its lowest point. Product dimensions 3/4" (1.9 cm) insulation -
... removing wheels from dishwasher. ** Minimum, measured from the lowest point on all models) 24-7/8" (63.2 cm) 24-1/2" (62.2 cm)* front vent 33-7/8" (86 cm) min. REAR VIEW 4 May be reduced to 6-5/8" (16.6 cm) if height of countertop. with wheels removed 21" (53.3 cm) SIDE VIEW 23-7/8" (60.6 cm) Cutout dimensions 24" (61...) * Measured from narrowest point of opening. *** May be compressed (not used on the underside of opening is 34-1/2" (87.6 cm) at its lowest point. Product dimensions 3/4" (1.9 cm) insulation -
Installation Instructions
Page 12
..."Install custom panel" section. 23-1/2" (59.7 cm) *30-3/16" (76.7 cm) 3/4" (19.1 mm) *This dimension is for 4" (10.2 cm) toe kick. For dishwashers with the control panel shown below : (models KUDS03FTPA and KUDU03FTPA) (Your model may vary slightly from picture above .) Custom ...door panel dimensions are : 1/8" (3.2 mm) 1/8" (3.2 mm) *This dimension is on your dishwasher before you order your custom door panel. Follow directions in Step 8. 11. Reinstall and tighten the three ...
..."Install custom panel" section. 23-1/2" (59.7 cm) *30-3/16" (76.7 cm) 3/4" (19.1 mm) *This dimension is for 4" (10.2 cm) toe kick. For dishwashers with the control panel shown below : (models KUDS03FTPA and KUDU03FTPA) (Your model may vary slightly from picture above .) Custom ...door panel dimensions are : 1/8" (3.2 mm) 1/8" (3.2 mm) *This dimension is on your dishwasher before you order your custom door panel. Follow directions in Step 8. 11. Reinstall and tighten the three ...
Installation Instructions
Page 13
... custom panel 13 hold the panel assembly in place on the front of the panel to side. 6. Place the outer panel on KitchenAid custom handle selection, refer to specific dimensions. IMPORTANT: Screw heads must be flush with the panel. Install custom panel Option 1: For models KUDS03FTPA and KUDU03FTPA NOTE: The handle for...
... custom panel 13 hold the panel assembly in place on the front of the panel to side. 6. Place the outer panel on KitchenAid custom handle selection, refer to specific dimensions. IMPORTANT: Screw heads must be flush with the panel. Install custom panel Option 1: For models KUDS03FTPA and KUDU03FTPA NOTE: The handle for...
Installation Instructions
Page 14
... top corners on both sides of the customer-supplied custom panel, and both panels are attached, shorter screws maybe required. 8. NOTE: These dimensions are available. Gently set outer panel aside. 3. make sure top edge of the customersupplied custom panel and align holes. 7. Attach outer panel to... specific dimensions. Lay the cutomer-supplied custom panel face down on the back of the console. 12. Mark all edges of the panel to attach ...
... top corners on both sides of the customer-supplied custom panel, and both panels are attached, shorter screws maybe required. 8. NOTE: These dimensions are available. Gently set outer panel aside. 3. make sure top edge of the customersupplied custom panel and align holes. 7. Attach outer panel to... specific dimensions. Lay the cutomer-supplied custom panel face down on the back of the console. 12. Mark all edges of the panel to attach ...