Installation Instructions
Page 3
...to level dishwasher.) NOTE: To prevent shifting during dishwasher operation, shims must provide: • easy access to take special care in measuring dimensions and in dishwasher • small level • TORX® T15 screwdriver (if installing custom front panels) • flashlight •...type clamp if connecting to waste-tee Parts needed : • electric drill with 3/8" N.P.T. Bottom sound pad (located in the "Cutout dimensions" section. Location Requirements Do not run drain lines, water lines or electrical wiring where they can interfere with certain models F. A side ...
...to level dishwasher.) NOTE: To prevent shifting during dishwasher operation, shims must provide: • easy access to take special care in measuring dimensions and in dishwasher • small level • TORX® T15 screwdriver (if installing custom front panels) • flashlight •...type clamp if connecting to waste-tee Parts needed : • electric drill with 3/8" N.P.T. Bottom sound pad (located in the "Cutout dimensions" section. Location Requirements Do not run drain lines, water lines or electrical wiring where they can interfere with certain models F. A side ...
Installation Instructions
Page 4
...-7/8" (63.2 cm) 24-1/2" (62.2 cm)* front vent 33-7/8" (86 cm) min. REAR VIEW 4 with wheels removed 21" (53.3 cm) SIDE VIEW 23-7/8" (60.6 cm) Cutout dimensions 24" (61 cm)** All surfaces must be free from intrusions 3-1/4" (8.3 cm) 24" (61 cm) min. 3-1/4" (8.3 cm) 34" (86.4 cm) min.* 2" (5.1 cm) 6" *** (15.2 cm) 3-1/2" (8.9 cm) 5-1/2" (14...- 1-1/2" (3.8 cm) direct wire - 3/4" (1.9 cm) power supply cord - 1-1/2" (3.8 cm) * Measured from narrowest point of opening. *** May be reduced to 6-5/8" (16.6 cm) if height of countertop. Product dimensions 3/4" (1.9 cm) insulation -
...-7/8" (63.2 cm) 24-1/2" (62.2 cm)* front vent 33-7/8" (86 cm) min. REAR VIEW 4 with wheels removed 21" (53.3 cm) SIDE VIEW 23-7/8" (60.6 cm) Cutout dimensions 24" (61 cm)** All surfaces must be free from intrusions 3-1/4" (8.3 cm) 24" (61 cm) min. 3-1/4" (8.3 cm) 34" (86.4 cm) min.* 2" (5.1 cm) 6" *** (15.2 cm) 3-1/2" (8.9 cm) 5-1/2" (14...- 1-1/2" (3.8 cm) direct wire - 3/4" (1.9 cm) power supply cord - 1-1/2" (3.8 cm) * Measured from narrowest point of opening. *** May be reduced to 6-5/8" (16.6 cm) if height of countertop. Product dimensions 3/4" (1.9 cm) insulation -
Installation Instructions
Page 12
... three remaining side screws. (Your model may vary slightly from picture above .) Custom door panel dimensions are : 23-3/8" (59.4 cm) 3/4" (19.1 mm) *25-29/32" (65.8 cm) Custom panel dimensions IMPORTANT: You need to know what control panel is for 4" (10.2 cm) toe kick....the control panel shown below : (models KUDS03FTPA and KUDU03FTPA) (Your model may vary slightly from picture above .) Custom door panel dimensions are : 1/8" (3.2 mm) 1/8" (3.2 mm) *This dimension is for 4" (10.2 cm) toe kick. tighten corner screws. If the installation needs a higher toe kick, adjust the ...
... three remaining side screws. (Your model may vary slightly from picture above .) Custom door panel dimensions are : 23-3/8" (59.4 cm) 3/4" (19.1 mm) *25-29/32" (65.8 cm) Custom panel dimensions IMPORTANT: You need to know what control panel is for 4" (10.2 cm) toe kick....the control panel shown below : (models KUDS03FTPA and KUDU03FTPA) (Your model may vary slightly from picture above .) Custom door panel dimensions are : 1/8" (3.2 mm) 1/8" (3.2 mm) *This dimension is for 4" (10.2 cm) toe kick. tighten corner screws. If the installation needs a higher toe kick, adjust the ...
Installation Instructions
Page 13
...panel. Save screws for reinstallation. 23-1/2" (59.7 cm) *30-3/16" (76.7 cm) custom panel dimensions 3/4" (19.1 mm) *This dimension is the consumer's responsibility to the KitchenAid Catalog, visit www.kitchenaid.com, or call 1-800-422-1230. align holes. 8. do not tighten completely. Attach the handle....will hold the outer panel up while removing the screws. For more than 6" (15.2 cm). 7. Place the outer panel on KitchenAid custom handle selection, refer to obtain the proper length screws and adjust the pilot holes accordingly. Gently set outer panel aside. 3. Attach...
...panel. Save screws for reinstallation. 23-1/2" (59.7 cm) *30-3/16" (76.7 cm) custom panel dimensions 3/4" (19.1 mm) *This dimension is the consumer's responsibility to the KitchenAid Catalog, visit www.kitchenaid.com, or call 1-800-422-1230. align holes. 8. do not tighten completely. Attach the handle....will hold the outer panel up while removing the screws. For more than 6" (15.2 cm). 7. Place the outer panel on KitchenAid custom handle selection, refer to obtain the proper length screws and adjust the pilot holes accordingly. Gently set outer panel aside. 3. Attach...
Installation Instructions
Page 14
...screws reinstalled in customer-supplied custom panel. 6. Option 2: For models KUDC03IT, KUDK03IT and KUDL03IT All models require an accessory option to specific dimensions. Not recommended for 4" (10.2 cm) toe kick. hold the outer panel up while removing the screws. IMPORTANT: Use a moisture resistant...remove three screws from both sides and all four hole locations; Place the outer panel on each side. 3 screws 1/8" (3.2 cm) *This dimension is less than 3/4" (1.9 cm) thick where the screws are available. align top edges drill through the holes in the top corners of the...
...screws reinstalled in customer-supplied custom panel. 6. Option 2: For models KUDC03IT, KUDK03IT and KUDL03IT All models require an accessory option to specific dimensions. Not recommended for 4" (10.2 cm) toe kick. hold the outer panel up while removing the screws. IMPORTANT: Use a moisture resistant...remove three screws from both sides and all four hole locations; Place the outer panel on each side. 3 screws 1/8" (3.2 cm) *This dimension is less than 3/4" (1.9 cm) thick where the screws are available. align top edges drill through the holes in the top corners of the...