Kenwood WD-K10series Support and Manuals
Get Help and Manuals for this Kenwood item
This item is in your list!
View All Support Options Below
Free Kenwood WD-K10series manuals!
Problems with Kenwood WD-K10series?
Ask a Question
Free Kenwood WD-K10series manuals!
Problems with Kenwood WD-K10series?
Ask a Question
Popular Kenwood WD-K10series Manual Pages
User Manual - Page 2
...
23
Interface Cable WD-RC50
24
Interface Cable WD-RC100
25
2 PREPARATION
26
2.1 Preparing the Device
26
Replacing the Battery Pack
...WD-K10PBS in Transceiver
Mode
38
2.4 Setting Various Functions
39
Adjusting the Receiver Volume Level
39
Checking Battery Remaining Capacity 40
Configuring in Setup Menu Mode
41
Setting Key Lock On/Off
43
Changing the PTT Key Setting
44
Manual...
User Manual - Page 7
...part of the plug. If the device is dirty, wipe with a dry clean cloth. 0 When connecting the clip microphone with earphone or headset, be sure to turn off the
dirt.
Model Portable base WD-K10PBS Transceiver WD...adjust the speaker volume or change drastically depending on the radio wave environment and setup condition. This may cause malfunction. 0 When pulling off the clip microphone, ...
User Manual - Page 10
...the Portable base as a base unit. Portable Type
0 Stand-alone
One Portable Base WD-K10PBS is a DECT intercom system that combines and uses both base and sub units. ...on the settings, please consult the authorized dealer or installer.
Contents
9
The system may be of base unit. For details on system configuration and setup, please consult the authorized dealer or installer. 1 ...
User Manual - Page 14
... of range, call disabled)
―
Listening Mode
System error
Wireless setting by the PC
Normal Mode
―
Menu Setup
―
Updating
Updating
0 Blinking (slow): Blinks every 3 seconds
Blinking (fast...Call] key.
For details, please consult the authorized dealer or installer. 1 INTRODUCTION 1.8 Part Names and Functions (Device Connection Method)
A Antenna
B PMR Link jack
For...
User Manual - Page 15
....
Do not connect any device other than the compatible models. N Charge contact terminal
Contents
14 I Microphone
When ... do not touch the connector.
1 INTRODUCTION 1.8 Part Names and Functions (Device Connection Method)
H Power...settings.
0 Normally not used.
M Data setting connector
For registering the transceiver to check the remaining capacity in preparation, or charging error...
User Manual - Page 26
... transceiver and noise may occur during conversation.
Contents
25 1 INTRODUCTION 1.8 Part Names and Functions (Device Connection Method)
Interface Cable WD-RC100
The transceiver connection cable WD-RC100 is a conversion cable for communication between the DECT intercom system WD-K10 series and external wireless system (KENWOOD brand). (For universal connector) It is used to connect to...
User Manual - Page 29
... off when charging is set up.
Transceiver (WD-K10PBS / WD-K10TR)
Charger (KSC-...installing and removing the bracket, refer to charge WD-K10PBS and WD-K10TR.
Take out the transceiver. 0 The estimated time required to complete the charging is as follows:
WD-K10PBS: Approx. 6 hours WD-K10TR: Approx. 5 hours
Precautions
0 Be sure to use the specified charger WD-C100CR to the instruction manual...
User Manual - Page 30
... read the instruction manual of the connecting device before using the supplied belt clip.
Tighten again periodically. Screws (supplied) The screws can be attached to a belt using .
0 Make sure to the DECT intercom system WD-K10 series website. Making a connection while the transceiver is also disabled.
0 For information on the transceiver. http://manual.kenwood.com...
User Manual - Page 31
...installer. Connecting to a Portable base WD-K10PBS
Insert the connecting plug into the connecting jack of the transceiver, and secure by turning the cap in the direction of the KENWOOD brand that can be connected to the transceiver connection cable WD... error due to allow communication between the DECT intercom system WD-K10 series and external wireless systems (KENWOOD brand).
0 Compatible models...
User Manual - Page 43
... ends automatically when the duration configured elapses. * VOX: The microphone automatically turns ON in setup menu mode
*: Default setting
Item (Voice Announcement) Base Station Select (Base Select)
Talk Setting (Talk Setting)
VOX Sensitivity (VOX Level) Mic Gain (Mic Gain)
Settings
Content
Auto*/Base 1/Base 2/Base Switches the base unit (Portable base or Base station) to...
User Manual - Page 50
... 0 The PTT, PTT-Lock and VOX settings can make a call while the [PTT] key on this manual. Note
0 The default setting is being pressed.
Operation on this transceiver or...dealer or installer.
1 Speak into the microphone while pressing the [PTT] key on the clip microphone or transceiver.
2 Release the [PTT] key to "Setting
Various Functions (Setup menu mode)" ( on
the setting.
For ...
User Manual - Page 55
...WD-RC100 to connect the Transceiver WD-K10TR and Portable base WD-K10PBS to connect the transceiver connection cable WD-RC100 ( on the system setup, please consult the authorized dealer or installer.
0 As far as this is not turned properly, the transceiver will not be output. Target transceivers: KENWOOD two-way radios
Models using WD...external wireless systems. An error
due to radio wave ...
User Manual - Page 61
... operation of the [PTT] key to the function keys by a single operation. For details, please
consult the authorized dealer or installer. Activating the Broadcast Function
The following activation methods are not assigned to broadcast. Contents
60 Note
0 By assigning the Broadcast (PTT...(PTT Link)] key and link the call to the key operation to connect external devices and set up the system.
User Manual - Page 65
It is effective for giving instructions or replying to only specific people and where other people only... Talk (Call-capable)
155
155
Or
Base Unit (Base Station)
Up to configure the system setup of the sub unit. Precautions
0 To use Listening Mode, it is necessary to 64 units ...Listening Mode.
Overview of calls)
Contents
64 To change the setting, consult the
authorized dealer or installer.
User Manual - Page 70
... details, please consult the authorized
range). Broadcast is
destination at the default setting.
entering service non- When a sub unit is Only one person can The unit is...installation site or use All Call or Wait for repairs.
on the radio wave status, If the unit is prone to the same output
Broadcast, and try again. 5 OTHERS
5.1 Troubleshooting
Check that the problem...
Kenwood WD-K10series Reviews
Do you have an experience with the Kenwood WD-K10series that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Kenwood yet.
Earn 750 points for your review!