Kenwood NX-900 Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood NX-900 manuals!
Problems with Kenwood NX-900?
Ask a Question
Free Kenwood NX-900 manuals!
Problems with Kenwood NX-900?
Ask a Question
Popular Kenwood NX-900 Manual Pages
Instruction Manual 1 - Page 3
VHF DIGITAL TRANSCEIVER
NX-700 NX-700H
UHF DIGITAL TRANSCEIVER
NX-800 NX-800H
700MHz DIGITAL TRANSCEIVER
NX-900
800MHz DIGITAL TRANSCEIVER
NX-901
INSTRUCTION MANUAL
Instruction Manual 1 - Page 5
... metal box with a padded interior.
If you have added to your radio.
This voice coding Technology is licensed solely for JVC KENWOOD Corporation. The user of copyrights for information on fuel or while parked in gasoline service stations. Firmware Copyrights The title to and ownership of this Technology is protected by fine and...
Instruction Manual 1 - Page 6
...instructions, may be against harmful interference in the event of a collision. These limits are designed to provide reasonable protection against traffic laws. Check the battery polarity and voltage of the vehicle before installing the transceiver.
◆ Use only a KENWOOD...equipment and receiver. • Connect the equipment to Part 15 of the FCC Rules. This equipment generates,...
Instruction Manual 1 - Page 9
...KENWOOD dealer, an authorized KENWOOD service...set
• 5 x 16 mm self-tapping screw 4 • Hex-headed screw with the carrier immediately.
We recommend that you identify the items listed in the following unpacking instructions are missing or have been damaged during shipment, file a claim with washer 4 • Spring washer 4 • Flat washer 4 • Instruction manual...
Instruction Manual 1 - Page 10
...wiring or parts. If your vehicle may malfunction. The following preparation instructions are typical examples of equipment that may malfunction if they are required for installing the ...KENWOOD dealer, an authorized KENWOOD service facility, or the factory. When drilling mounting holes, be removed for the make of the vehicle before installing the transceiver.
◆ Use only a KENWOOD...
Instruction Manual 1 - Page 25
... with FleetSync can communicate with other transceivers set up with FleetSync II. Note: This function is a protocol owned by JVC KENWOOD Corporation. Repeat this process until the entire ID is entered...When the call station's ID appears on the display, you can respond to the call .
• If Manual Dialing is a voice call to a particular station or to a group of the station you want to call...
Instruction Manual 1 - Page 26
...to make a call to all units (Broadcast call . • If Manual Dialing is fixed and cannot be selected. Messages can be reviewed after...the digits to select a digit, then press the key to set the digit and move the cursor to call ). Repeat this ... are reserved for special messages). ■ Identification Codes
An ID code is received or the new message will be erased when a...
Instruction Manual 1 - Page 32
... (DQT)
Your dealer may seem like you have your own private channel while using QT/ DQT, other parties can
set up your desired tone or code, the OST function is a sub-audible tone/code which allows you to save your transceiver channels. Although it may have programmed QT or DQT signaling on the...
Operation Manual - Page 2
ENGLISH
800MHz DIGITAL TRANSCEIVER 900MHz DIGITAL TRANSCEIVER
NX-900/NX-901
INSTRUCTION MANUAL
Operation Manual - Page 5
...; Use only a Kenwood optional DC power cable. ◆ Do not cut and/or remove the fuse holder on the DC power cable.
These limits are designed to Part 15 of the FCC Rules. However, there is made.
For passenger safety, install the transceiver securely using an optional mounting bracket and screw set so the...
Operation Manual - Page 8
... are missing or have been damaged during shipment, file a claim with washer 4 • Spring washer 4 • Flat washer 4 • Instruction manual 1
1 If any items are for use by your Kenwood dealer, an authorized Kenwood service facility, or the factory. UNPACKING AND CHECKING EQUIPMENT
Note: The following table before discarding the packing material.
Carefully unpack the...
Operation Manual - Page 24
... FleetSync can communicate with other transceivers set up either FleetSync or FleetSync II on your transceiver, some of paging functions on the display, you can respond to the call by JVC KENWOOD Corporation.
The calling station's ID will automatically enter Selcall Mode. When the call .
• If Manual Dialing is entered.
4 Press the...
Operation Manual - Page 25
... the digits to select a digit, then press the key to set the digit and move the cursor to transmit. • If Manual Dialing is received or the new message will be erased when a... new message is enabled, you can send and receive 2-digit Status messages which is entered.
18 ■ Identification Codes
An ID code...
Operation Manual - Page 26
GPS data can be manually transmitted by pressing the key programmed as Status messages and are stored in the same stack ...function through the Menu
{page 12}.
SHORT MESSAGES
To send a short message, you must connect the transceiver to the transceiver. If set up by pressing and holding the key for 1 second. LONG MESSAGES
To send and receive long messages, you must first connect ...
Operation Manual - Page 31
... for 1 second.
• The icon appears on the same channel you are using OST, press the OST key to save your new setting. When a channel is set up to 40 tones/codes.) 4 Press the key to turn the OST function OFF.
24 If a call . When you have finished operating using the same channel...
Kenwood NX-900 Reviews
We have not received any reviews for Kenwood yet.