Kenwood NX-740H Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood NX-740H manuals!
Problems with Kenwood NX-740H?
Ask a Question
Free Kenwood NX-740H manuals!
Problems with Kenwood NX-740H?
Ask a Question
Popular Kenwood NX-740H Manual Pages
Operation Manual - Page 1
INSTRUCTION MANUAL
VHF DIGITAL TRANSCEIVER
NX-740H NX-740HV
UHF DIGITAL TRANSCEIVER
NX-840H NX-840HU
B5A-0031-20 (K)
Operation Manual - Page 3
... occur in gasoline service stations.
Firmware Copyrights The title to radio communications. These limits are reserved for information on fuel or while parked in a particular installation. Patent Nos. #5,826,222, #5,754,974, #5,701,390, and #5,715,365. This instruction manual covers only the basic operations of copyrights for firmware embedded in KENWOOD product memories...
Operation Manual - Page 4
...; Do not expose the transceiver to configure the transceiver while driving; For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set so the transceiver will not break loose in your KENWOOD dealer. • Use of the transceiver while you are driving may be against traffi...
Operation Manual - Page 5
..., an authorized KENWOOD service facility, or the factory.
DC power cable (with fuses 1 • 15 A fuse 2 Mounting Bracket 1 Screw set • 5 x 16 mm self-tapping screw 4 • M4 x 8 mm Hex-headed screw with washer 4 • Spring washer 4 • Flat washer 4 Microphone (with cable) • KMC-30 (NX-740H/ NX-840H 1 • KMC-35 (NX-740HV/ NX-840HU 1 Microphone...
Operation Manual - Page 6
...replace a fuse with the safe operation of a collision.
Note: Before installing the transceiver, check how far the mounting screws will not break loose in the DC power cable, be sure to replace... Installing the Transceiver
For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set,...cable to damage vehicle wiring or parts.
1 Mark the position of the...
Operation Manual - Page 8
... Display (Zone 1)
7
Zone Display (Zone 2)
7
Channel Display (Channel 16)
7
Appears during the transceiver is stunned. (St)
10
4 Appears when switch the transceiver ON.
6
The Transceiver Password function is programmed. (PS)
Appears during Scan. (Sc)
8
The selected channel is the Priority channel. (P)
9
Appears when a channel is added to the scan list. (cA...
Operation Manual - Page 9
...Sr)
12
Appears when the Encryption function is on. (Ec)
12
Appears when the Scrambler/ Encryption code mode is on. (co)
12
Appears when the Squelch Level setting is on. (SL)
13
Appears when the Public Address function is on. (PA)
13
Appears... as listed below.
• Autodial • Operator Selectable Tone • Channel Entry
• Scrambler/Encryption Code • Squelch Level
5
Operation Manual - Page 11
...into the microphone to transmit. Press again to switch the transceiver OFF.
■ Transceiver Password To enter the password: 1 Press / to select a digit. • When using the keys programmed as ... steps 1 and 2 to enter the entire password. 3 Press S or to code your transceiver settings. Note: Signaling allows your transceiver to confirm the password. • If you will hear a call...
Operation Manual - Page 12
...start / stop scanning, press the key programmed as [Call 1] or [Call 2], if they have set up with an individual or group ID list number. Various data communications, including individual and group voice ...the call will sound and you receive a group call and the received group ID matches the ID set up on the display during Scan. • When a signal is present. To start the call ...
Operation Manual - Page 13
...number, or enter the list
number directly (1 ~ 9). • "A1" (Autodial list 1) appears on dealer setting). MANUAL DIALING
1 Press and hold the PTT switch. 2 Enter the desired digits using the keypad.
• If ...Keypad Auto-PTT is no data in the redial memory, an error tone will automatically change to the Priority channel when a call is received on that have been...
Operation Manual - Page 14
... receives a call . The DTMF decode capabilities include Selective Call ID, Transpond with a revive code. • "St" appears on the display while the transceiver is received. Note: The transceiver..., squelch will not hear the call containing a stun code, the transceiver becomes disabled. STUN
This function is used when a transceiver is set up with the built-in MDC signaling: PTT ID ...
Operation Manual - Page 15
...of FleetSync.
Note: If set up by your dealer, your...CALLING)
A Selcall is installed on the display, followed by JVC KENWOOD Corporation. Note: The... ID range may use the MDC-1200 feature in a regular call; GPS REPORT
If a GPS unit (NMEA-0183 format) is a voice call , press the PTT switch and speak into the microphone.
■ Identification Codes An ID code...
Operation Manual - Page 16
... the Emergency channel and begin transmitting based on how the transceiver is set up.
2 To exit Emergency mode, press and hold a conversation ... not operated for 1 second. TALK AROUND
During interruptions in service (such as [Talk Around] to communicate by using the ... transceiver will change the scrambler/ encryption codes:
12 ADVANCED OPERATIONS
EMERGENCY CALLS
If your transceiver has been programmed...
Operation Manual - Page 17
... as [Squelch Level]. • "SL" appears on the display, followed by the current scrambler/ encryption code.
2 Press to select your desired scrambler/ encryption code. 3 Press S or to store the new setting.
• After changing your scrambler/ encryption code, be used with an optional relay unit. HORN ALERT
The Horn Alert function can readjust your...
Operation Manual - Page 18
... is already in analog operation. If BCL Override has been programmed, you would during a normal call. PTT ID
PTT ID is the transceiver unique ID code which is sent each time the PTT switch is already in analog operation. Release the PTT switch to sound and the transceiver will sound.
Pressing...
Kenwood NX-740H Reviews
We have not received any reviews for Kenwood yet.