Kenwood NX-720G Support and Manuals
Get Help and Manuals for this Kenwood item
This item is in your list!
View All Support Options Below
Free Kenwood NX-720G manuals!
Problems with Kenwood NX-720G?
Ask a Question
Free Kenwood NX-720G manuals!
Problems with Kenwood NX-720G?
Ask a Question
Popular Kenwood NX-720G Manual Pages
User Manual - Page 2
...install the transceiver securely using the supplied mounting bracket and screw set...KENWOOD product memories are carried in progress, or where "TURN OFF TWO-WAY RADIO" signs have adopted separate waste collection systems)
Products and batteries with a padded interior.
NOTICES TO THE USER
Firmware Copyrights The title to and ownership of copyrights for firmware embedded in gasoline service...
Operation Manual - Page 3
VHF DIGITAL TRANSCEIVER
NX-720 NX-720G
UHF DIGITAL TRANSCEIVER
NX-820 NX-820G
INSTRUCTION MANUAL
NOTIFICATION This equipment complies with the essential requirements of Directive 2014/53/EU.
AT BE DK FI FR DE GR IS IE IT LI LU NL NO PT ES SE CH GB CY CZ EE HU LV LT MT PL SK SI BG RO HR TR
ISO3166 This equipment requires a licence and is intended for use in the countries as below.
Operation Manual - Page 5
...
We are grateful you have chosen KENWOOD for countries that the operator is punishable by fine and/or imprisonment. ◆ Refer service to you are transporting blasting caps ...a padded interior. Information on Disposal of handling these items and their waste byproducts.
This instruction manual covers only the basic operations of , and understands, hazards common to explode. If you...
Operation Manual - Page 6
Please check
and observe the vehicle regulations in your KENWOOD dealer. • Use of a collision.
For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set so the transceiver will not break loose in the event of the transceiver while you are driving may be against traffic laws.
it...
Operation Manual - Page 7
...servicing while keeping the power applied.
1 DC power cable (with fuses 1 • 15 A fuse 2 Mounting Bracket 1 Screw set • 5 x 16 mm self-tapping screw 4 • M4 x 6 mm hex-headed screw with washer 4 • Spring washer 4 • Flat washer 4 Instruction manual...
Note: The following instructions are for use a circle cutter to drill a hole, then install a rubber grommet.
...
Operation Manual - Page 9
GETTING ACQUAINTED
FRONT AND REAR VIEWS
ab
c
j
kl
d ef
g
h
m
i n
① (Power) switch Press to switch the transceiver ON or OFF.
② / keys Press to activate their programmable functions {page 5}.
③ / keys Press to this connector.
⑭ Power input connector Connect the DC Power Cable to activate their programmable functions {page 5}.
⑧ Speaker Internal speaker...
Operation Manual - Page 16
... which may be stored in the selected fleet (Fleet call . • If Manual Dialing is enabled, you want to a station or group of a 3-digit Fleet number ... by pressing the PTT switch and speaking into the microphone.
■ Identification Codes An ID code is a combination of stations.
■ Transmitting 1 Select your conversation.
■ Receiving... by JVC KENWOOD Corporation.
Operation Manual - Page 17
...set up by pressing the key programmed as [Send the GPS data]. 5 Press the / key to select the status you want to transmit. • If Manual Dialing is enabled, you can enter a station ID by using the NX-720/ NX... time may be automatically transmitted at a preset time interval. • When using the NX-720G/ NX-820G, you must connect a KRA-40 GPS antenna. • When using the microphone...
Operation Manual - Page 19
Press any key to return to enter Manual Input mode. Press the / key to select the digit you can enter the Code directly by using the microphone DTMF keypad.
6 Press the key programmed as [Call 1] to [... message will appear when a Status call is received. Or, you want to change the Code Up or Down. • In Selcall List Mode, press and hold the S or key for 1 second to normal operation.
...
Operation Manual - Page 20
DTMF (DUAL TONE MULTI FREQUENCY) CALLS
MANUAL DIALING
1 Press and hold the PTT switch. 2 Enter the desired digits using the microphone DTMF keypad. 3 Press the PTT switch to make the call. AUTODIAL
...
Operation Manual - Page 22
... a sub-audible tone/code which allows you can reprogram the QT/DQT settings on each of time necessary to hold the key programmed as [Emergency].
• Ask your dealer for further information.
Contact your KENWOOD dealer for the length of your channels. 16 ADVANCED OPERATIONS
EMERGENCY CALLS
If your transceiver has been programmed...
Operation Manual - Page 23
...■ Squelch Level If a key has been programmed as [Squelch Level], you can set up to 40 tones/codes. 4 When you have finished operating using OST, press the [OST] key again...: Press to deactivate QT, DQT, DTMF, 5-tone, or FleetSync Signaling. When a channel is set up with one of optional signaling for digital radio communications.
Release to return to normal operation. •...
Operation Manual - Page 171
VHF
NX-720 NX-720G
UHF
NX-820 NX-820G
2014/53/EU
AT BE DK FI FR DE GR IS IE IT LI LU NL NO PT ES SE CH GB CY CZ EE HU LV LT MT PL SK SI BG RO HR TR
ISO3166
Operation Manual - Page 185
4 S 5
DTMF 3 6 PTT COMPLETE
1 Selcall Selcall Stack 2 ID S S 1 3 A S A 1 S ή .
48
15
GPS
GPS GPS GPS NX-720G/ NX-820G GPS KRA-40 NX-720/ NX-820 GPS GPS είναι
G-11
Operation Manual - Page 196
... types NX-720-E, NX-720G-E, NX-820-E, NX-820G-E are described in the EU declaration of conformity is available at the following internet address: http://www.kenwood.com/cs/com/ecdoc/ (Note: The detail type designations are in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity.)
Model NX-720-E NX-720G-E NX-820-E NX-820G...
Kenwood NX-720G Reviews
Do you have an experience with the Kenwood NX-720G that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Kenwood yet.
Earn 750 points for your review!