Kenwood NX-720 Support and Manuals
Get Help and Manuals for this Kenwood item
This item is in your list!
View All Support Options Below
Free Kenwood NX-720 manuals!
Problems with Kenwood NX-720?
Ask a Question
Free Kenwood NX-720 manuals!
Problems with Kenwood NX-720?
Ask a Question
Popular Kenwood NX-720 Manual Pages
Operation Manual - Page 3
AT BE DK FI FR DE GR IS IE IT LI LU NL NO PT ES SE CH GB CY CZ EE HU LV LT MT PL SK SI BG RO HR TR
ISO3166
This equipment requires a licence and is intended for use in the countries as below. VHF DIGITAL TRANSCEIVER
NX-720 NX-720G
UHF DIGITAL TRANSCEIVER
NX-820 NX-820G
INSTRUCTION MANUAL
NOTIFICATION This equipment complies with the essential requirements of Directive 2014/53/EU.
Operation Manual - Page 5
...may cause them to explode. If you .
THANK YOU
We are grateful you have chosen KENWOOD for details in locating a recycle facility nearest to you are transporting blasting caps in your ... fine and/or imprisonment. ◆ Refer service to qualified technicians only. This instruction manual covers only the basic operations of dynamite blasting caps may have been posted.
Operation Manual - Page 6
For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set so the transceiver will not break loose in 12 V negative ground systems only!
Please check
and observe the vehicle regulations in your KENWOOD dealer. • Use of the transceiver while you are driving may be against traffic laws...
Operation Manual - Page 7
...Mounting Bracket 1 Screw set • 5 x 16 mm self-tapping screw 4 • M4 x 6 mm hex-headed screw with washer 4 • Spring washer 4 • Flat washer 4 Instruction manual 1
PREPARATION
Various electronic...drill a hole, then install a rubber grommet.
2 Run the power cable through . • If no hole exists, use by your KENWOOD dealer, an authorized KENWOOD service facility, or the ...
Operation Manual - Page 11
...below. When assigned, the dealer must
set the key assignment hold to "Enable... Scan • Scan Delete/Add • Scrambler/ Encryption • Scrambler/ Encryption Code • Selcall 8 • Selcall + Short Message 8 • Selcall + Status...8226; Status • Talk Around 8 • Transfer 3 • Transceiver Password • Volume Down • Volume Up • Zone Delete/Add •...
Operation Manual - Page 16
... a call to all units in the selected fleet (Fleet call . • If Manual Dialing is enabled, you can be decided in analog operation. Messages can respond to make an ... ID code is a combination of 15 received messages (combined status messages and short messages) can enter a station ID by using the microphone DTMF keypad by JVC KENWOOD Corporation. A maximum of a 3-digit Fleet...
Operation Manual - Page 17
... for 1 second. 5 Press the / key to select the status you want to transmit. • If Manual Dialing is enabled, you must connect an external GPS unit. • When the power is turned ON and/...ID by your dealer, GPS data may take longer.
11 A maximum of your transceiver. If set up by using the NX-720/ NX-820, you can be stored in the Stack Memory 1 Press the key programmed as [Stack...
Operation Manual - Page 22
... Talk (DQT) Your dealer may have programmed QT or DQT signaling on your KENWOOD dealer for the length of time necessary to hold this key before the transceiver ...This function cannot be used in use before Emergency mode was in certain countries. A QT tone/ DQT code is set the transceiver to the zone and channel that was entered.
Contact your transceiver channels.
SCRAMBLER (ANALOG) / ...
Operation Manual - Page 171
VHF
NX-720 NX-720G
UHF
NX-820 NX-820G
2014/53/EU
AT BE DK FI FR DE GR IS IE IT LI LU NL NO PT ES SE CH GB CY CZ EE HU LV LT MT PL SK SI BG RO HR TR
ISO3166
Operation Manual - Page 185
4 S 5
DTMF 3 6 PTT COMPLETE
1 Selcall Selcall Stack 2 ID S S 1 3 A S A 1 S ή .
48
15
GPS
GPS GPS GPS NX-720G/ NX-820G GPS KRA-40 NX-720/ NX-820 GPS GPS είναι
G-11
Operation Manual - Page 196
... text of the EU declaration of conformity is available at the following internet address: http://www.kenwood.com/cs/com/ecdoc/ (Note: The detail type designations are in the EU declaration of conformity.)
Model NX-720-E NX-720G-E NX-820-E NX-820G-E
Frequency range
TX/RX
136.000 - 174.000 MHz
TX/RX
136.000 - 174.000...
Operation Manual 1 - Page 1
NX-720 NX-820
VHF DIGITAL TRANSCEIVER UHF DIGITAL TRANSCEIVER
INSTRUCTION MANUAL
B62-2448-10 (C)
Operation Manual 1 - Page 3
... prohibits the operation of unlicensed transmitters within 500 feet (150 m) of this Communications Equipment. U.S.
Firmware Copyrights The title to and ownership of your mobile radio. This instruction manual covers only the basic operations of copyrights for firmware embedded in KENWOOD product memories are reserved for use within this Technology is either standing near to or...
Operation Manual 1 - Page 5
...; Spring washer 4 • Flat washer 4 Instruction manual 1
PREPARATION
Various electronic equipment in 12 V negative...1 • 15 A fuse 2 Mounting Bracket 1 Screw set • 5 x 16 mm self-tapping screw 4 ...KENWOOD dealer, an authorized KENWOOD service facility, or the factory.
GETTING STARTED
Note: The following instructions are for use a circle cutter to drill a hole, then install...
Operation Manual 1 - Page 15
... Message, ME: Short Message • Press and hold the S or key for 1 second. If set up by your location data, you can receive short data messages which contain a maximum of
15 received... messages (combined status messages and short messages) can be manually transmitted by using the microphone DTMF keypad (refer to step 3, above).
6 Press the PTT ...
Kenwood NX-720 Reviews
Do you have an experience with the Kenwood NX-720 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Kenwood yet.
Earn 750 points for your review!