Kenwood NX-700H Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood NX-700H manuals!
Problems with Kenwood NX-700H?
Ask a Question
Free Kenwood NX-700H manuals!
Problems with Kenwood NX-700H?
Ask a Question
Popular Kenwood NX-700H Manual Pages
Instruction Manual 1 - Page 3
VHF DIGITAL TRANSCEIVER
NX-700 NX-700H
UHF DIGITAL TRANSCEIVER
NX-800 NX-800H
700MHz DIGITAL TRANSCEIVER
NX-900
800MHz DIGITAL TRANSCEIVER
NX-901
INSTRUCTION MANUAL
Instruction Manual 1 - Page 5
... is protected by fine and/or imprisonment. ◆ Refer service to explode. This instruction manual covers only the basic operations of any customized features they are carried ... of copyrights for firmware embedded in KENWOOD product memories are reserved for information on fuel or while parked in gasoline service stations.
The AMBE+2TM voice coding Technology embodied in...
Instruction Manual 1 - Page 6
...instructions, may cause harmful interference to Part 15 of the transceiver while you are driving may be against harmful interference in the event of the vehicle before installing the transceiver.
◆ Use only a KENWOOD... radio frequency energy. For passenger safety, install the transceiver securely using an optional mounting bracket and screw set so the transceiver will not occur in ...
Instruction Manual 1 - Page 9
... missing or have been damaged during shipment, file a claim with washer 4 • Spring washer 4 • Flat washer 4 • Instruction manual 1
1
If any items are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. Carefully unpack the transceiver. SUPPLIED ACCESSORIES
• Microphone (with cable 1 • Microphone hanger (with 4 x 16...
Instruction Manual 1 - Page 10
...installing the transceiver.
◆ Use only a KENWOOD... use by your KENWOOD dealer, an authorized KENWOOD service facility, or the...for servicing while keeping the power applied.
2 TOOLS REQUIRED
Note: Before installing .... The following preparation instructions are typical examples of equipment that...a circle cutter to drill the firewall, then install a rubber grommet.
2 Run the two power cable ...
Instruction Manual 1 - Page 25
...respond to the call .
• If Manual Dialing is enabled, you want to set up with FleetSync II, and vice-versa....KENWOOD Corporation. Note: This function is a protocol owned by pressing the microphone PTT switch and speaking into the microphone.
17 SELCALL (SELECTIVE CALLING)
A Selcall is received. The calling station's ID will automatically enter Selcall Mode. However, transceivers set...
Instruction Manual 1 - Page 26
... • Enter an ID number to make a call . • If Manual Dialing is entered.
18 Messages can contain up to 99 (80 ~ 99 ... The icon lights when a message is stored in your dealer settings, when the stack memory is full, either the oldest message...keys.
When using the / keys. ■ Identification Codes
An ID code is fixed and cannot be reviewed after reception. Note: ...
Instruction Manual 1 - Page 27
... 15 Status calls and short messages can be automatically transmitted at a preset time interval.
19 If set up by accessing the Send the GPS data function through the Menu {page 12}.
GPS data can be manually transmitted by pressing the key programmed as Send the GPS data, or by your dealer for...
Instruction Manual 1 - Page 32
....
24 Although it may have finished operating using , squelch will not open when a call containing a different tone or code is a sub-audible tone/code which allows you can reprogram the QT/DQT settings on each of your channels. 1 Select your desired channel. 2 Press and hold the key programmed as OST for 1 second...
Operation Manual - Page 1
NX-700H(T) NX-800H(T)
VHF DIGITAL TRANSCEIVER/ UHF DIGITAL TRANSCEIVER
INSTRUCTION MANUAL
© B62-2457-00 (K) 09 08 07 06 05 04 03 02 01 00
Operation Manual - Page 3
...transceiver is punishable by fine and/or imprisonment. ◆ Refer service to qualified technicians only. Do not carry spare fuel containers in ...metal box with a padded interior.
This instruction manual covers only the basic operations of dynamite blasting caps may have chosen KENWOOD for information on fuel or while parked in gasoline service stations.
THANK YOU We are being ...
Operation Manual - Page 7
... 1 • Screw set
• 5 x 16 mm self-tapping screw 4 • Hex-headed screw with the carrier immediately. If any items are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory... instructions are missing or have been damaged during shipment, file a claim with washer 4 • Spring washer 4 • Flat washer 4 • Instruction manual 1
1
Operation Manual - Page 20
... 99 (80 ~ 99 are using a microphone keypad and Manual Dialing is a combination of your transceiver.
■ Transmitting ...to make a group call. • Enter a Fleet number followed by JVC KENWOOD Corporation. A maximum of stations.
■ Transmitting 1 Select your desired zone ...and speaking into the microphone.
■ Identification Codes An ID code is enabled, you can contain up to ...
Operation Manual - Page 21
... same stack memory. When using / , cycle through the digits to select a digit, then press to set up by accessing the Menu {page 9}. To confirm the deletion, press or # for 1 second to ...your dealer, GPS data may be automatically transmitted at a preset time interval.
15
GPS data can be manually transmitted by pressing the key programmed as follows: ID Name > Status/Short Message > CH/GID >...
Operation Manual - Page 23
...1 Press and hold this key before Emergency mode was entered.
TELEPHONE CALLS
■ Making a Telephone Call Manual Dialing (Analog) 1 Select your desired zone and telephone group ID. 2 Press the PTT switch to start ... select your desired list number. 4 Press the PTT switch to start the call is set the transceiver to emit tones and received signals as [Emergency].
• Ask your desired...
Kenwood NX-700H Reviews
We have not received any reviews for Kenwood yet.