Kenwood NX-5400 Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood NX-5400 manuals!
Problems with Kenwood NX-5400?
Ask a Question
Free Kenwood NX-5400 manuals!
Problems with Kenwood NX-5400?
Ask a Question
Popular Kenwood NX-5400 Manual Pages
User Manual 3 - Page 3
... VHF DIGITAL TRANSCEIVER
NX-5200
UHF DIGITAL TRANSCEIVER
NX-5300
700/800MHz DIGITAL TRANSCEIVER
NX-5400
USER GUIDE
The AMBE+2™ voice coding Technology embodied in this...KENWOOD Corporation is licensed solely for use of copyrights for JVC KENWOOD Corporation.
. Firmware Copyrights The title to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in KENWOOD...
User Manual 3 - Page 4
...ACCESSORIES 13 PREPARATION ...14
INSTALLING/ REMOVING THE (OPTIONAL) BATTERY PACK 14 INSTALLING THE (OPTIONAL) ANTENNA 15 INSTALLING THE BELT CLIP 15 INSTALLING THE CAP OVER THE UNIVERSAL CONNECTOR 16 INSTALLING THE (OPTIONAL) SPEAKER/ MICROPHONE OR HEADSET ...... 16 INSTALLING... Guide covers only the basic operations of your Digital Transceiver applications. For using details User Manual,...
User Manual 3 - Page 5
...approved in a particular installation. This equipment generates, uses and can be applicable:
FCC WARNING This equipment generates or uses radio frequency energy.
Safety: It is important that the interference will not occur in the instruction manual. INFORMATION TO THE ... to try to correct the interference by fine and/or imprisonment. ● Refer service to qualified technicians only.
User Manual 3 - Page 6
.... This device complies with your area, call (toll free) 1-800-8-BATTERY (1-800-822-8837). Under Industry Canada regulations, this program is part of a type and maximum (or lesser) gain approved for successful communication.
4 KENWOOD's involvement in this radio transmitter may cause undesired operation of our commitment to disposing Li-ion batteries with Industry...
User Manual 3 - Page 7
...; Do not use options not specified by KENWOOD. ● If the die-cast chassis or other transceiver part is damaged, do not
touch the damaged parts. ● If a headset or headphone ...connected to remove the water from the speaker and/or microphone before installing optional accessories.
5 Do not touch these locations when replacing the battery pack. ● When water gets into the microphone ...
User Manual 3 - Page 8
... reverse side of the transceiver is specifically qualified for such use (Intrinsically Safe... the use of the transceiver must follow the instructions
and regulations provided by Factory Mutual, CSA):
...While taking on fuel or while parked at gasoline service stations.
●
WARNING Do not remove the... the following locations, unless
the model is important
with foreign materials.
...
User Manual 3 - Page 9
replace
only with the same type.
● To dispose of the transceiver while you use only a speaker/microphone in such conditions, it is durable. When the airbag inflates, the transceiver may be
ejected and strike the driver...from
the transceiver, and contact your KENWOOD dealer.
● Use of ...parts are driving may be against traffic
laws. When using
an earphone accessory...
User Manual 3 - Page 12
...transceiver may be used in U.S. Lightly shake the transceiver to remove the water from KENWOOD. b) Do not disassemble or attempt to modify the transceiver. (If it is ...
● Observe the following standards. NOTIFICATION OF WATER-RESISTANT MODEL
Water Resistance and Maintenance
Water-Resistant Model transceiver conforms to the following precautions to maintain the transceiver's waterresistant...
User Manual 3 - Page 15
If any items are for belt clip (M3 x 8 mm 2 Universal connector cap 1 ● Dressing screw 1 ● Packing (preassembled 1 User Guide 1
13 SUPPLIED ACCESSORIES
Belt clip 1 ● Screws for use by your KENWOOD
dealer, an authorized KENWOOD service facility, or the factory. Carefully unpack the transceiver. We recommend that you identify the items listed below before discarding...
User Manual 3 - Page 18
...) SPEAKER/ MICROPHONE OR HEADSET
1 Insert the guide of the speaker/ microphone or headset connector into the groove of the transceiver, and can only be used with NX-5000 series Portable models.
16
Optional speaker/ microphone
Note: ● When not using an optional speaker/ microphone or headset, install
the cap over the universal connector.
2 Secure...
User Manual 3 - Page 20
... transceiver OFF, turn counterclockwise fully. Rotate to activate its programmable function. The default setting is Channel Select.
18
B Selector knob Rotate this control to adjust the volume level. ORIENTATION KEYS AND CONTROLS
Speaker Microphone
Standard Key model
Full Key model
microSD memory card slot
A Power switch/ Volume control Turn clockwise to switch the...
User Manual 3 - Page 21
... programmable function.
Lights red while transmitting and green while receiving. Switch to position A or B to turn on the function programmed to "DISPLAY" {p. 21} .
M 4-way D-pad Press to activate its programmable function. [H] : The default setting is [None]. [I Side 3 key Press to activate its programmable function. Flashes red when the battery power is low...
User Manual 3 - Page 22
... setting is programmed as Function. P Keypad (Full key model only) Press the keys on your transceiver, please contact your dealer or refer to send DTMF tones. The keypad keys can also be programmed with secondary functions if a programmable function key is [None]. For details on programming functions to the keys on the keypad to the instruction manual...
User Manual 3 - Page 26
... the Power switch/ Volume control to switch the transceiver power OFF. Each channel is programmed with settings for transmitting and receiving. ● The default setting for the Selector knob is [Channel Select]. ● The transceiver may have names programmed for zones and channels. The zone name and channel name can contain up to switch...
User Manual 3 - Page 27
Release the PTT switch to 4 cm) from your transceiver settings.
25 If signaling has been programmed on the selected channel, you will hear a call only if the received signal matches your mouth. This indicator can also be disabled by your dealer. &#...
Kenwood NX-5400 Reviews
We have not received any reviews for Kenwood yet.