Kenwood NX-248 Support and Manuals
Get Help and Manuals for this Kenwood item
This item is in your list!
View All Support Options Below
Free Kenwood NX-248 manuals!
Problems with Kenwood NX-248?
Ask a Question
Free Kenwood NX-248 manuals!
Problems with Kenwood NX-248?
Ask a Question
Popular Kenwood NX-248 Manual Pages
Operation Manual - Page 1
INSTRUCTION MANUAL
VHF DIGITAL TRANSCEIVER
NX-248
UHF DIGITAL TRANSCEIVER
NX-348
© B5A-0068-10 (C)
Operation Manual - Page 3
Firmware Copyrights The title to and ownership of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use ...; Refer service to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in KENWOOD product memories are grateful you have chosen KENWOOD for JVC KENWOOD Corporation.
The user of any other way convert the Object Code into a...
Operation Manual - Page 4
...instructions
and regulations provided by the airline crew.) • Where restrictions or warnings are no metallic items located between the transceiver and the battery pack.
• Do not use options not specified by KENWOOD. • If the die-cast chassis or other transceiver part... power off before installing optional accessories. ...touch these locations when replacing the battery pack. ...
Operation Manual - Page 5
... may result in such conditions, it is possible for any metallic parts are driving may be against traffic laws. you use only...shocks. • To dispose of batteries, be ejected and strike the driver or passengers. • Do not transmit while touching the antenna terminal... where the air is dry, it is easy to your KENWOOD dealer. • Use of the transceiver while you are exposed...
Operation Manual - Page 9
... items listed below are missing or damaged, file a claim with NX-348 1 • Cap 1 • Locking bracket 1 • Belt clip (KBH-10 1 • Screw (M3 x 8 mm 2 • Channel stopper 1 • Instruction manual 1 Note: ◆ Refer to "PREPARATION" {p. 2} for accessory installation instructions.
1 SUPPLIED ACCESSORIES
• Antenna (Supplied with the carrier immediately...
Operation Manual - Page 10
... antenna at channel 1, the knob may
not install correctly and the channel may damage the antenna and degrade your transceiver's performance.
2 Inserting the Channel stopper prevents unnecessarily selecting channels which do not exist. • Selecting a channel which does not exist causes a continuous error
tone to sound. 1 Set the Channel selector to channel 1, then...
Operation Manual - Page 17
If the transceiver is "Operator Selectable", press this key in normal mode to set the current channel as Key Lock except that when the transceiver power is turned OFF and then ON again, the keys remains locked.
■ Lone ...
Operation Manual - Page 19
... confirm the password. • When the correct password is password protected, the LED will light blue when you enter an incorrect password, an error tone sounds and the transceiver remains locked. The transceiver announces the digit number as it .
11 Enter the password (up to 4 digits) using the following procedure. 1 Set the Channel selector to...
Operation Manual - Page 20
...and speak into the microphone. Refer to check whether or not the channel is free. • If the channel is programmed with settings for transmitting and receiving. SELECTING A ZONE AND CHANNEL
1 Select the desired zone using the key programmed as [Monitor] or [... transceiver approximately
1.5 inches (3 ~ 4 cm) from listening to unwanted calls.
Release the PTT switch to code your mouth.
Operation Manual - Page 21
...used .
* Your dealer can be used if you to transmit hands-free. To activate VOX and set the LED to hold the Side 1 key until a beep sounds. • The LED indicator ...VOX Gain level.
13 VOICE OPERATED TRANSMISSION (VOX)
VOX operation allows you are using a supported headset.
VOX can set the VOX Gain level, perform the following steps:
1 Connect a headset to the transceiver. ...
Operation Manual - Page 22
... the setting. • A beep will exit VOX setup mode.
14
Note: ◆ If key lock with the Channel selector). When turned OFF, a double beep sounds. • When the sector points to empty channel, pressing Side 2 key will cause the error tone to sound.
5 Press the PTT switch to key in the correct password before...
Operation Manual - Page 23
...the call , press the key programmed as [Call 1] or [Call 2], if they have been set up with an NXDN Status. • Channels are possible. Various data communications, including individual and ...target transceiver by your transceiver, a ringing tone will sound. INDIVIDUAL/GROUP CALLS
Each channel is set up with ID list numbers by pressing the key programmed as [Paging Call]. • ...
Operation Manual - Page 24
...that is operating, the LED may flash green
when receiving a QT/DQT signal which does not match the QT/ DQT tone/code set up in use. Release the PTT switch to sound and the transceiver will sound. BATTERY SAVER
When activated by your transceiver. Note: ...present and no signal is released and the LED indicator blinks red when the battery needs recharged or replaced. To stop the tone.
Operation Manual - Page 25
... (RAN) RAN is a signaling system designed for digital radio communications.
If a call containing a different RAN is set up with ID, and "Wild Card" Group Calling.
17 When a channel is made only in use, a ... the channel is pressed and/or released. PTT ID
PTT ID is the transceiver unique ID code which is sent each time the PTT switch is already in analog operation. If BCL Override ...
Kenwood NX-248 Reviews
Do you have an experience with the Kenwood NX-248 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Kenwood yet.
Earn 750 points for your review!