Kenwood NX-1800 Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood NX-1800 manuals!
Problems with Kenwood NX-1800?
Ask a Question
Free Kenwood NX-1800 manuals!
Problems with Kenwood NX-1800?
Ask a Question
Popular Kenwood NX-1800 Manual Pages
User Manual - Page 2
CONTENTS
MODELS COVERED BY THIS MANUAL 5 PREPARATION 6
CONNECTING THE POWER CABLE 6 INSTALLING THE TRANSCEIVER 7 OPTIONS...9 ORIENTATION 11 FRONT VIEW 11 REAR VIEW 12 MICROPHONE 12
Display...13 BASIC OPERATIONS 15
SWITCHING ... 18 ACCESSIBLE FUNCTIONS 19 FUNCTION MODE 19 MENU MODE 19 Menu Access 20 FUNCTIONS LIST 21 FUNCTIONS OVERVIEW 26 Setting value/ Speaker connection status 36
2
User Manual - Page 5
... BY THIS MANUAL
The models listed below are covered by this manual: NXDN/ Analog Transceiver
NX-1700HNV NX-1700HN NX-1700N NX-1800HNU NX-1800HN NX-1800N
VHF TRANSCEIVER VHF TRANSCEIVER VHF TRANSCEIVER UHF TRANSCEIVER UHF TRANSCEIVER UHF TRANSCEIVER
K type K type E type K type K type E type
DMR/ Analog Transceiver
NX-1700HDV NX-1700HD NX-1700D NX-1800HDU NX-1800HD NX-1800D
VHF TRANSCEIVER...
User Manual - Page 6
... can be passed through. • If no hole exists, use a circle cutter to drill a hole, then install a rubber
grommet. 2 Run the power cable through the firewall and into the engine compartment. 3 Connect the red...in your vehicle contains such equipment, consult the dealer for servicing while keeping the power applied.
6 Typical examples include electronic fuel injection, anti-skid braking, and cruise...
User Manual - Page 9
Model Name KAS-20 KCT-18 KCT-23M KCT-36 KCT-60 KPG-46U KPG-46X KDI-03
KES-5/ 5A KES-8K KLF-2 KMB-10 KMB-...
User Manual - Page 21
... that can be programmed to the transceiver buttons Menu : Functions that can be accessed using the transceiver Menu Analog : Channels set up for Analog NXDN : Channels set up for NXDN DMR : Channels set up for DMR ✔: Available N/A: Not Available
Function
None 2-tone
Menu Display
PF Button
Menu
Analog
NXDN
DMR
-
✔
N/A
✔...
User Manual - Page 23
Function
Lone Worker Low Transmit Power Maintenance Manual Site Hunt Medium Transmit Power Menu Microphone Sense Microphone Type Monitor Monitor Momentary Operator Selectable Tone OST List OVCM Priority-channel Select Public Address Radio ...
User Manual - Page 32
...end a call . PF Button: Press the programmed button to increase/ decrease the 5-tone selcall code by 10 with each press.
2nd digit code from the right of 5-tone selcall code
32
Clear [Analog/ NXDN/ DMR] Allows you to cancel the data (Status Message, Short...is displayed for 1 second. CW Message [NXDN] Sending CW Message. PF Button: Press the programmed button to send the set Morse code.
User Manual - Page 33
Menu Mode: Select "DR 1 SEL" ~ "DR 5 SEL" and press the [ S ] button to the formerly selected channel. • If activated by your dealer, you can set your own Direct Channels by selecting
your desired zone and channel using Direct Channel 1 ~ 5. PF Button: 1 Press the programmed button to jump to a frequently used ...
User Manual - Page 34
Display Format [Analog/ NXDN/ DMR] Allows you to switch the display between the zone-channel number and the channel name. Menu Mode: Select "DISP FMT" and press the [ S ] button to switch the display between the zone-channel number and the channel name. Zone-channel number Channel name
PF Button: Press the programmed button to change the Display Format setting.
34
User Manual - Page 35
... is in Emergency Mode, press and hold this button for the time set in hold the programmed button for entering Emergency Mode if the transceiver is...the transceiver repeats transmission and reception at regular intervals. External Microphone Sense [Analog/ NXDN/ DMR] Allow you to set in Hold Delay to enter Emergency Mode.
• If transceiver is in standby mode. Refer to confirm and...
User Manual - Page 36
Internal Speaker
External Speaker
Both Speaker
Setting value/ Speaker connection status
None
KES-8K
KES-5/ 5A
Internal Speaker
External Speaker
Both Speaker
Internal Speaker
None
Internal Speaker
KES-8K None
KES-8K
...
User Manual - Page 49
... the transceiver Menu.
49 Menu Mode: Select "M SITE HNT" and press the [ S ] button, the Manual Site Hunt function operates. • Search Mode Tone sounds and send a Wakeup message once to other
Channels registered in the same System set in DMR Site Roaming and go to resume. Medium Transmit Power [Analog/ NXDN/ DMR...
User Manual - Page 59
... sound to a specific level for your dealer. Menu Mode: Select "SCAN STS" and press the [ S ] button to start scanning. To stop scanning, press this transceiver. • This function is for field support use such for easy....
3 Press the [ S ] button to "SCAN" {page 71}.
59 Scan [Analog/ NXDN/ DMR] Allows you to set the transceiver to automatically adjust the volume of this button.
User Manual - Page 77
... the [Operator Selectable Tone] button to ignore (not hear) these calls. When a channel is set up with the same tone or code. If a call containing a different tone or code is received. COLOR CODE (CC) [DMR]
Color Code is a sub-audible tone/ code which allows you to activate the OST function. Although it may have your own...
User Manual - Page 80
...messages are 2-digit codes ranging from 10 to...The " " icon appears when a message is stored in your dealer, GPS data may be manually transmitted by pressing the button programmed as [Status] to enter Status Mode (proceed to
step ...any button to return to 99 (80 ~ 99 are reserved for special messages).
If set up by accessing the Menu. By configuring a name consisting of a maximum of 10 ...
Kenwood NX-1800 Reviews
We have not received any reviews for Kenwood yet.