Kenwood NX-1300D Support and Manuals
Get Help and Manuals for this Kenwood item
View All Support Options Below
Free Kenwood NX-1300D manuals!
Problems with Kenwood NX-1300D?
Ask a Question
Free Kenwood NX-1300D manuals!
Problems with Kenwood NX-1300D?
Ask a Question
Popular Kenwood NX-1300D Manual Pages
User Manual 2 - Page 5
MODELS COVERED BY THIS MANUAL
The models listed below are covered by this manual: NXDN/ Analog Transceiver
NX-1200N (VHF TRANSCEIVER) NX-1300N (UHF TRANSCEIVER) DMR/ Analog Transceiver NX-1200D (VHF TRANSCEIVER) NX-1300D (UHF TRANSCEIVER)
5
User Manual 2 - Page 21
...; N/A ✔
✔
✔✔
Zone Up (Continuous)
-
✔ N/A ✔
✔
✔✔
*1: [Channel Select] can be programmed only on the Selector of the Non-LCD model.
Cannot be set with [Channel Up] and/or [Channel Down] together.
*2: [Channel Up/Down] can be programmed only on the Selector of the LCD...
User Manual 2 - Page 64
..., repeat for only the number of digits the password contains.
4 Press the PTT switch to confirm the password. • When the correct password is password protected, the LED will light blue when you turn the transceiver ON. Non-LCD Model
If your transceiver is entered, the Blue LED turns off.
64 The transceiver announces the...
User Manual 2 - Page 70
... function off. This allows you to ignore (not hear) calls from 1 to 40.
4 Press the [ S ] button to save your new setting. • After selecting and setting up with the same tone or code. When a channel is made on each of your channels by OST List.
1 Select your desired channel.
2 Press and hold the...
User Manual 2 - Page 74
If set up by accessing the Menu. GPS REPORT
GPS data can receive short data messages which contain a maximum of the GPS
satellite is poor, positioning may take longer to complete.
74
SHORT MESSAGES
This transceiver can be manually transmitted by pressing the button programmed as [Send the GPS Data], or by your...
User Manual 3 - Page 2
CONTENTS
MODELS COVERED BY THIS MANUAL 5 PREPARATION 6
INSTALLING THE ANTENNA 6 INSTALLING/ REMOVING THE BATTERY PACK 6 INSTALLING THE BELT CLIP 7 INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE JACKS....... 7 INSTALLING THE ... (LCD Model 15 Menu Access 15 FUNCTIONS LIST 17 FUNCTIONS OVERVIEW 22 FUNCTION DESCRIPTIONS 63 TRANSCEIVER PASSWORD 63 LCD Model...63 Non-LCD Model 64 SCAN...65
2
User Manual 3 - Page 5
... BY THIS MANUAL
The models listed below are covered by this manual: NXDN/ Analog Transceiver
NX-1200NV : VHF TRANSCEIVER NX-1200N : VHF TRANSCEIVER NX-1300NU : UHF TRANSCEIVER NX-1300N : UHF TRANSCEIVER DMR/ Analog Transceiver NX-1200DV : VHF TRANSCEIVER NX-1200D : VHF TRANSCEIVER NX-1300DU : UHF TRANSCEIVER NX-1300D : UHF TRANSCEIVER Analog Transceiver NX-1200AV : VHF TRANSCEIVER NX-1200A : VHF...
User Manual 3 - Page 17
...
PF Button : Functions that can be programmed to the transceiver buttons Menu : Functions that can be accessed using the transceiver Menu Non-LCD : Non-LCD Model Analog : Channels set up for Analog NXDN : Channels set up for NXDN DMR : Channels set up for DMR ✔ : Available N/A : Not Available
Function None
Menu Display
-
User Manual 3 - Page 21
...; N/A ✔
✔
✔✔
Zone Up (Continuous)
-
✔ N/A ✔
✔
✔✔
*1: [Channel Select] can be programmed only on the Selector of the Non-LCD model. Cannot be set with [Channel Up] and/or [Channel Down] together.
*2: [Channel Up/Down] can be programmed only on the Selector of the LCD...
User Manual 3 - Page 23
...two represents low power, and one time, recharge or replace your dealer, the backlight can turn the display backlight On... by your battery pack immediately. Battery remaining
LED
Beep tone
Indicator (LCD-Model)
Full
Blink 4 times
Sounds 4 times
Sufficient
Blink 3 times
Sounds 3... NXDN/ DMR]
Allows you can be set to
activate by the number of flashes from the LED.
23 Backlight...
User Manual 3 - Page 40
... operates. • Search Mode Tone sounds and send a Wakeup message once to other
Channels registered in the same System set in DMR Site Roaming and go to search for repeaters that can manually move the Revert Channel to another Channel without waiting for Site Roaming to select and perform functions using a channel...
User Manual 3 - Page 70
... may have your own private channel while using QT/ DQT, other parties can still hear your calls if they set up with [Operator Selectable Tone], you can reprogram the QT tone or DQT code on the same channel you are using the same channel. Press this button again to ignore (not hear...
User Manual 4 - Page 5
MODELS COVERED BY THIS MANUAL
The models listed below are covered by this manual: NXDN/ Analog Transceiver
NX-1200N (VHF TRANSCEIVER) NX-1300N (UHF TRANSCEIVER) DMR/ Analog Transceiver NX-1200D (VHF TRANSCEIVER) NX-1300D (UHF TRANSCEIVER) Analog Transceiver NX-1200A (VHF TRANSCEIVER) NX-1300A (UHF TRANSCEIVER)
5
User Manual 4 - Page 73
... press the button programmed as [Operator Selectable Tone].
• Alternatively, you have programmed QT or DQT signaling on your calls if they set up with the same tone or code. If a call . Press this button again to ignore (not hear) calls from other parties who are using the Menu Mode.
3 Press the...
User Manual 2 - Page 1
... using details instruction manual, refer to the sales country.
Note: ◆ The handling models are driving may reduce or void the water resistant and dust resistant performance. TRANSCEIVER
NX-1000 series
USER GUIDE
This User guide covers only the basic operations of channels. For using the buttons programmed as [Channel Up]/ [Channel Down]. https://manual.kenwood.com/files...
Kenwood NX-1300D Reviews
We have not received any reviews for Kenwood yet.