Instruction Manual
Page 2
...of the unit becomes hot and may cause your Kenwood dealer. • Do not touch the unit during installation, consult your Kenwood dealer. • If the unit does not seem to be greater than the output power of the amplifier will not occur in the instruction manual. These... limits are expressly approved in a particular installation. terminal. Use of speakers having input power ratings that are going ...
...of the unit becomes hot and may cause your Kenwood dealer. • Do not touch the unit during installation, consult your Kenwood dealer. • If the unit does not seem to be greater than the output power of the amplifier will not occur in the instruction manual. These... limits are expressly approved in a particular installation. terminal. Use of speakers having input power ratings that are going ...
Instruction Manual
Page 4
.... Remote cable (6.0 m : 19.7 ft) Remote controller 4 English Sharing the negative wire of the speaker or grounding speaker wires to the metal body of the same rating. • Check that the brake lamps, winkers, and wipers work properly. Do not remove caps from unconnected wires or connectors to prevent short circuits. •...
.... Remote cable (6.0 m : 19.7 ft) Remote controller 4 English Sharing the negative wire of the speaker or grounding speaker wires to the metal body of the same rating. • Check that the brake lamps, winkers, and wipers work properly. Do not remove caps from unconnected wires or connectors to prevent short circuits. •...
Instruction Manual
Page 6
...p q rs t u vw x y z{ 1 Fuse (40 A × 1) NOTE If you can't find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Ground terminal 4 Power control terminal Controls the unit ON/OFF. ON position: The audio signal adjusted when setting LPF, INPUT SENSIVITY control... and Bass boost (optional accessory) is any indication of the amplifier. NOTE For the pre-output level, refer to these terminals. 2CAUTION The rated input of the speakers should be no less than the maximum output of trouble. (See page...
...p q rs t u vw x y z{ 1 Fuse (40 A × 1) NOTE If you can't find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Ground terminal 4 Power control terminal Controls the unit ON/OFF. ON position: The audio signal adjusted when setting LPF, INPUT SENSIVITY control... and Bass boost (optional accessory) is any indication of the amplifier. NOTE For the pre-output level, refer to these terminals. 2CAUTION The rated input of the speakers should be no less than the maximum output of trouble. (See page...
Instruction Manual
Page 7
...ohms, 1 % THD+N ...300 W × 1 Signal to Noise Ratio (Reference: 1Watt into 4 ohms) ...80 dBA Audio Section Max Power Output...1200 W Rated Power Output (+B = 12.0 V) (4 Ω) (20 Hz - 200 Hz, 0.5 % THD)...200 W × 1 (2 Ω) (100 Hz, 0.5 % THD)...400 W ×... Hz, 0.5 % THD)...600 W × 1 (1 Ω) ...≥ 600 W × 1 Frequency Response (+0, -3 dB)...5 Hz - 200 Hz Sensitivity (rated output) (MAX.) ...0.2 V Sensitivity (rated output) (MIN.) ...5.0 V Input Impedance ...10 kΩ Signal to Noise Ratio...105 dB Low Pass Filter Frequency (-24 dB/oct.)...40 - 200 Hz (variable) ...
...ohms, 1 % THD+N ...300 W × 1 Signal to Noise Ratio (Reference: 1Watt into 4 ohms) ...80 dBA Audio Section Max Power Output...1200 W Rated Power Output (+B = 12.0 V) (4 Ω) (20 Hz - 200 Hz, 0.5 % THD)...200 W × 1 (2 Ω) (100 Hz, 0.5 % THD)...400 W ×... Hz, 0.5 % THD)...600 W × 1 (1 Ω) ...≥ 600 W × 1 Frequency Response (+0, -3 dB)...5 Hz - 200 Hz Sensitivity (rated output) (MAX.) ...0.2 V Sensitivity (rated output) (MIN.) ...5.0 V Input Impedance ...10 kΩ Signal to Noise Ratio...105 dB Low Pass Filter Frequency (-24 dB/oct.)...40 - 200 Hz (variable) ...